Owner’s Manual Read this manual for complete instructions Français - page 13 / Español - página 25 Contents 2 3 4 5 6 Important Safety Information Controls and Functions Assembly Material Preparation Spraying 8 9 10 11 36 40 Cleanup - Flushing the unit Cleanup - Cleaning the spray gun Reassembly / Maintenance Troubleshooting Parts List Limited Warranty Questions? Call Wagner Technical Service at: 1-800-328-8251 Monday - Friday 8:00 am to 4:30 pm CST 0712 • Form No.
Important Safety Safety Information Read all safety information before operating the equipment. Save these instructions Indicates a hazardous situation which, if not avoided, could result in death or serious injury. a) To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and proper usage of the equipment. Grounding Instructions This product must be grounded.
Controls and Functions White Spray Gun Yellow Spray Gun Adjustment ring Air cap Material flow adjustment Trigger Start Notice: Review the information on this page to familiarize yourself with the controls and functions of your unit. Material flow adjustment Air cap Trigger Material container Material container ON/OFF switch: The ON/OFF switch turns power to the turbine on and off. The ON/OFF switch is located on top of the carrying handle of the turbine.
Assembly Start 1 2 3 Notice: Your unit includes two spray guns. See below to determine the correct spray gun for your spraying project. Yellow spray gun designed for spraying thinner materials, such as oil-based stains and thinned paints. The yellow spray gun leaves a smooth finish. White spray gun designed for spraying thicker materials, such as latex paints and stains. Spraying with this gun will leave a slightly coarser finish that is between a roller and fine-finish sprayer. 1.
Material Preparation Start 1 3 1. Stir the spraying material thoroughly. Do not thin with materials that have a flashpoint below 70°F (21°C). The material flashpoint should be shown on the material container. Note: Material to be sprayed should always be strained to remove any impurities in the paint which may enter and clog the system. Impurities in the paint will give poor performance and a poor finish.
Material Flow Adjustment Spraying Start Notice: Spray performance will depend upon a number of factors: material thickness, spray pattern selected, material volume, and air pressure. With any type of air-assisted spraying, desired spray results will be achieved through some trial and error while adjusting some or all of these variables. Review these pages to learn about the spray controls and how they can be used to acheive the desired spray results.
= Proper Spraying Technique The room you are spraying must be properly masked in order to prevent overspray from STOP covering woodwork, floors or furnishings. Make sure you have properly masked the room per the instructions on the enclosed “Taping Guide”. If spraying with an air-assisted spray system is new or unfamiliar to you, it is advisable to practice on a piece of scrap wood or cardboard before beginning on your intended workpiece.
Cleanup - Flushing the unit 1 2 3 1/2 Start Before you begin: PULL When cleaning, use the appropriate cleaning solution (warm, soapy water for latex materials; mineral spirits for oil-based materials) important: Never clean nozzle or air holes in the spray gun with sharp metal objects. Do not use solvents or lubricants containing silicone. • • • • Special cleanup instructions for use with flammable solvents (must have a flashpoint above 70ºF (21ºC): Always flush spray gun outside.
Cleanup Cleaning the spray gun Start Yellow Gun 1 2 3 Before you begin: When cleaning, use the appropriate cleaning solution (warm, soapy water for latex materials; mineral spirits for oil-based materials) important: Never clean nozzle or air holes in the spray gun with sharp metal objects. Do not use solvents or lubricants containing silicone. • • • • Special cleanup instructions for use with flammable solvents (must have a flashpoint above 70ºF (21ºC): Always flush spray gun outside.
Maintenance 1 2 (d) (c) 3 (b) (e) Start Important: You should inspect the air filter in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. important: Never operate your unit without the air filters. Dirt could be sucked in and interfere with the function of the unit. * Cup seal It is important that the cup seal inside the spray gun be re-installed properly.
Troubleshooting Problem A: Little or no material flow 1. 2. 3. 4. 5. 6. Cause Nozzle clogged. Suction tube clogged. Material volume setting turned too low (-). Suction tube loose. No pressure build up in container. Air filter clogged. Any attempt to open the motor housing or repair any electrical parts within the unit by anyone other than an authorized repair technician could cause serious injury and will void the warranty. Problem D: Spray jet pulsates Solution Clean. Clean. Increase volume setting (+).
Parts List • Liste de pièces • Lista de piezas Spray Guns • Pistolets • Pistolas 1 2 4 8 7 6 3 5 11 13 12 14 15 9 17 16 18 10 19 21 20 Replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. Los repuestos están disponibles llamanado al servicio a clientes.
Item Part No. English Français Español Quantity Article Nº de piéce Description Description Descripción Quantite Articulo Pieza No.
Parts List • Liste de pièces • Lista de piezas 1 4 3 2 5 Replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. Los repuestos están disponibles llamanado al servicio a clientes.
Item Part No. English Français Español Quantity Article Nº de piéce Description Description Descripción Quantite Articulo Pieza No.
Limited warranty Garantie limitée Garantía limitada HVLP paint spray equipment Pulvérisateur de peinture HVLP Equipo de atomización de pintura HVLP This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted against defects in material and work-manship for one year following date of purchase if operated in accordance with Wagner’s printed recommendations and instructions.
