Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000Commissioning
124 Product manual | Version: 2.1.0
8PORT IOL-B FLD PN DC 24V 2.0A
Table 66: Identify Devices
Node Name Node Class Access Description
SerialNumber Variable Read Serial number of the de-
vice
SoftwareRevision Variable Read Revision/version of the de-
vice firmware
10.2.5.1.2 Configuring Parameters
The OPC UA server provides nodes with configuration parameters for the device. For ex-
ample, the OPC UA client can read out the upper limiting value for temperature in the
OverTemperature node. The path to this node is:
Root > Object > DeviceSet > [device name] > IOLinkMaster > Diag-
nostics > Configuration
The following table lists device-specific configuration parameters.
Table 67: Device-Specific Configuration Parameters
Node Name Node Class Access Description
CurrentHysteresis Variable Read Current hysteresis; unit:
mA
If the current exceeds the
limiting value, the current
must fall back below the
limiting value by the hys-
teresis to revoke the diag-
nosis.
OverTemperature Variable Read Upper limiting value for the
temperature of a port; unit:
0.1°C
OverVoltageL Variable Read Upper limiting value for the
voltage in supply cable 1;
pins with the following
functions can be moni-
tored: L+, DI, DO, DIO, IO-
Link; unit: mV
OverVoltageL2 Variable Read Upper limiting value for the
voltage in supply cable 2;
unit: mV
TemperatureHysteresis Variable Read Temperature hysteresis;
unit: 0.1 °C
If the temperature exceeds
the limiting value, the tem-
perature must fall back be-
low the limiting value by
the hysteresis to revoke
the diagnosis.
UnderTemperature Variable Read Lower limiting value for the
temperature of a port; unit:
0.1°C
UnderVoltageL Variable Read Lower limiting value for the
voltage in supply cable 1;
pins with the following
functions can be moni-
tored: L+, DI, DO, DIO, IO-
Link; unit: mV