Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Properties
Product manual | Version: 2.1.0 19
8PORT IOL-B FLD PN DC 24V 2.0A
Circuit High-side driver; no reverse current protection of the
1L+/2L+ output
Self-protection Overcurrent, overload and overtemperature
Voltage drop through high-side path Less than 200mV
Maximum capacitive load 1000μF parallel to 24Ω; 0.1Hz
470μF parallel to 12Ω; 0.1Hz
220μF parallel to 6Ω; 0.1Hz
Maximum inductive load 1.15H / 2A; 0.2Hz; DC13
Diagnostics (1L+, 2L+) Events: overcurrent, overload and overtemperature
4.4.4 Power Supply
Voltage 1L, 2L 24VDC, –25%/+30% (18VDC...31.2VDC)
Voltages above 34V can permanently damage the
product.
Voltages below approx. 10V lead to a product reset.
Undervoltage warning 17.0V (17.5V −3%) ON message,
18V (17.5V +3%) OFF message
Overvoltage warning 32.1V (31.2V +3%) ON message,
30.3V (31.2V −3%) OFF message
Module power consumption 1L: 0.2A (at 24VDC)
2L: 0.1A (at 24VDC)
Power consumption of supply connections Max. 16A; ensure external limitation or use fuses in
the cables
The maximum total current of the device, including
transmission between the power supply connections,
must not exceed 16A for both 1L and 2L individually. If
additional modules are connected to X32 (PWR OUT),
it may be necessary for the maximum total current to
be monitored with external power supply management.
Maximum current: Observe derating as a function of
temperature
Conductor cross-section For UL-compliant use: 2.5 mm
2
Reverse voltage protection Yes
4.4.5 Electrical Safety
Insulation resistance 60VDC
Test voltage 550VAC RMS
Min. creepage distance 0.7mm
Requirements
• Use of PELV/SELV power supplies with fault voltage limited to 60VDC.
• When SELV power supplies are used: SELV power supplies with supply via the same
network phase
• If PELV (Protective Extra Low Voltage) power supplies are used: PELV (Protective Ex-
tra Low Voltage) power supplies with a secondary power supply connection to the
common reference point
4.4.6 Environmental Conditions
Surrounding air temperature (operation) –25°C...+70°C
Surrounding air temperature (storage) –40°C...+80°C