Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Planning
Product manual | Version: 2.1.0 49
8PORT IOL-B FLD PN DC 24V 2.0A
Table 36: “DO” (Digital Output) Parameters
Parameter Group Parameters Default Value Range Description
Digital configuration DI logic I/Q pin 0 0: DI not inverted
(NO normally open)
Operating mode of
the digital input: The
signal on pin 2 is not
inverted
1: DI inverted (NC
normally closed)
Operating mode of
the digital input: The
signal on pin 2 is in-
verted
DI filter time I/Q pin 0 0: no filter No filter active for de-
tecting a signal
change of the pin 2
input signal.
30: 3ms filter time Filter time setting for
detecting a signal
change of the input
signal; the filter time
is the amount of time
the signal must be
present in order for a
signal change to be
detected.
150: 15ms filter time
200: 20ms filter time
DO static on I/Q pin 0 0: disable Pin 2 supplies no
output voltage
1: enable Pin 2 is a digital out-
put and supplies
+24VDC
DO static on C/Q pin 0 0: disable Pin 4 supplies no
output voltage
1: enable Pin 4 is a digital out-
put and supplies
+24VDC
Digital port parame-
ters
Enable port diagnos-
tics
1 0: disable The PROFINET port
diagnostics are dis-
abled, i.e. no diag-
nostic alarms are
triggered
1: enable PROFINET port di-
agnostics are en-
abled.
Configuration source 1 0: PDCT (Port and
Device Configuration
Tool)
Configuration is per-
formed via a “port
and device configu-
ration tool”
1: PNIO Configuration is per-
formed via the
PROFINET IO-Con-
troller
I/Q behavior 0 0: not supported Pin 2 is not used
1: digital input (only
class A)
Pin 2 is a digital input
2: digital output (only
class A)
Pin 2 is a digital out-
put