Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Installation and Removal
Product manual | Version: 2.1.0 53
8PORT IOL-B FLD PN DC 24V 2.0A
8Installation and Removal
8.1 Installation
8.1.1 Tools Required for Installation
The following tools are required for installation:
• Allen wrench for the M4 hex head mounting screws
The following additional items are only required for installation where no threaded hole is
present:
• M4 thread cutter (bottoming tap or hand tap set)
• Drill (for pre-drilling mounting holes for the module and installing the system)
You also need two M4 cylinder head hex screws per DIN 912 / ISO 4762 of adequate
length.
8.1.2 Before Installation
Always note the following information:
• The product must only be installed and put into operation by qualified electrical special-
ists per EN 50110‑1/-2 and IEC 60364.
• Observe the safety information in section 8Safety [}11].
• Before installation, check the product for damage, such as transport damage. Dam-
aged products must not be put into operation.
8.1.3 Installation Instructions
Note the following for selection of the installation location:
• Install the product in such a way that it is protected against weather exposure (no di-
rect sunlight; no salt water or spray).
• Note that the module should not be installed in the immediate vicinity of objects or de-
vices that can get hot. For a high level of module utilization, the temperature-depen-
dent operating range can be extended by installing metal surfaces or profiles or the
like, or by installation in a ventilated outdoor environment. The modules’ internal tem-
perature measurement can be used for optimization.
• Screw the product down only on flat contact surfaces to protect it from mechanical
warping.
• To protect the product from tensile forces that may arise, do not bridge spaces with it.
• To avoid damaging the product, do not mount it in shearing zones of moving devices.
Furthermore, lay the cables in such a way that they cannot get into the shearing zone
of movable equipment parts.
• Leave sufficient space for easy product replacement and for hooking up the pluggable
connections.
• Ensure that the requirements on the product concerning exposure to vibration and
shock are met at the installation location.
• Install the product in such a way that the product’s diagnostic LEDs remain visible.
Note the following concerning the installation procedure:
• Disconnect the power supply from the system before beginning mounting
• Ensure sufficient potential equalization in your system