Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Provisions
Product manual | Version: 2.1.0 7
8PORT IOL-B FLD PN DC 24V 2.0A
1Provisions
This documentation applies to the following product:
0765-4102/0100-0000.
1.1 Document Portfolio
Note
Observe the applicable documentation!
This product must only be installed and operated according to the instructions of the com-
plete Instructions for use. Knowledge of the complete Instructions for use is required for
proper use.
1. Carefully read the Product Manual.
2. Before commissioning, follow the instructions in section 8Safety [}11].
Table 1: Complete instructions for use
Document Type Contents
& Product Manual Contains all the product-specific information for a product.
& Data Sheet Contains the technical data for a product.
& Instruction leaflet Is included with each product. Contains initial information on safe handling of
the product.
All documentation is available at: üwww.wago.com /<item number>.
1.2 Intended Use
The product is for the acquisition and output via IO-Link to sensors, actuators and hubs of
field signals that are sent to a higherlevel controller or received.
The product serves as a decentralized input/output unit in PROFINET I/O networks.
• This product is intended for installation in automation technology systems.
• This product meets the requirements of protection type IP67 and is designed for use in
dry indoor spaces.
• This product is intended for use in indoor industrial areas without weather exposure (no
direct sunlight; no salt water or salt spray).
• Operation of the products in Industrial area is permitted.
• Operation of the product in other application areas is only permitted when correspond-
ing approvals and labeling are present.
Improper Use
Improper use of the product is not permitted. Improper use occurs especially in the follow-
ing cases:
• Non-observance of the intended use.