Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Commissioning
Product manual | Version: 2.1.0 73
8PORT IOL-B FLD PN DC 24V 2.0A
Table 43: Possible Values of “State” (Port Status Information)
Value Port Status Description
3 Preoperate The product is ready for communi-
cation
4 Operate The product is communicating
5 DI CQ The port is in digital input mode
6 DO CQ The port is in digital output mode
7 Reserved Reserved
8 Reserved Reserved
9 Incorrect Cycle Time The cycle time according to the con-
figuration does not correspond to
the connected product
254 Port Power Off The port voltage is switched off
255 Not Available The port is not available
10.2.2.3.5 Quality
This shows the Port Quality Info, including information on the validity of the process data
for input and output (separately). The content is binary coded.
Table 44: Meaning of the Individual Bits
Bits of Port Quality Info Description
Bit 0 0 = input process data valid
1 = input process data invalid
Bit 1 0 = output process data valid
1 = output process data invalid
Bit 2 to bit 7 Reserved
10.2.2.3.6 Revision ID
This shows the revision ID of the connected product.
A value of 0 means: no product connected.
All other values must be interpreted as the revision ID of the connected product.
10.2.2.3.7 Baud Rate
If an IO-Link product is connected to the port, its data transmission rate appears here. For
IO-Link, the transmission rate of the communication between the port and a connected
product can have the following values:
• 4.8kbit/s (COM1)
• 38.4kbit/s (COM2)
• 230.4kbit/s (COM3)
If no IO-Link product is connected to the port, the text Not connected appears here.
10.2.2.3.8 Cycle Time
The cycle time of the master is bit-coded as follows:
• Bits 0...5 specify a whole-number multiplier between 0 and63.
• Bits 6...7 specify the calculation formula to use according to the following table:
Table 45: Cycle Time of the Master
Bits 6...7 Calculation Formula
0 Multiplier * 0.1ms