Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Commissioning
Product manual | Version: 2.1.0 75
8PORT IOL-B FLD PN DC 24V 2.0A
Figure17: Port XX Menu Item, Process Data Tab
This example shows a configuration in which only process data for input has been config-
ured.
10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
You can make the following settings on the module with WAGO Webserver I/O Field:
• 8Accessing a Connected IO-Link Device [}75]
• 8Configuring Ports [}78]
• 8Configuring IP Parameters [}82]
• 8Storing Maintenance Information [}82]
• 8Updating Firmware [}84]
• 8Resetting Module to Factory Settings [}85]
• 8Configuring Bluetooth [}86]
• 8Logging Users on and off and Managing Them [}89]
• 8Forcing Digital Inputs and Outputs [}91]
• 8Forcing IO-Link ports [}92]
10.2.2.4.1 Accessing a Connected IO-Link Device
The IOL tab allows read and write access to the IO-Link device connected to an IO-Link
port via index and subindex. The ISDU message format (ISDU = Indexed Service Data
Unit) is used for this
Note
You can find the meaning of the index and subindex values in the documentation
of the connected IO-Link device.
You can find a description of the ISDU message format in the IO-Link specification.