Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000Commissioning
78 Product manual | Version: 2.1.0
8PORT IOL-B FLD PN DC 24V 2.0A
Time – Index:Subindex – Write ok: <Result>
If the operation was not successful, an error message appears in the history with error
codes from the IO-Link master and IO-Link device. The entries in the history then have
the following structure:
Time – Index:Subindex – Write failed: IOLMErrorCode(<error code of
the IO-Link master>): IOLDErrorCode(<error code of the IO-Link de-
vice>)
Deleting the Read and Write Access History
To delete the logged history of read and write access operations:
• Click the [Clear history] button
ð The history of read and write access operations is deleted.
10.2.2.4.2 Configuring Ports
Figure20: Port XX Menu Item, Configuration Tab
The Configuration tab is for viewing and modifying the following port settings individually
for the selected port of the device:
Table 46: Port Configuration Settings for IO-Link Devices
Name Type Explanation
Port mode Drop-down list Port operating mode (configuration
of pin 4)
Digital input signal filter (pin 4) Drop-down list Filter time for digital input signals on
pin 4
IQ behavior (pin 2) Drop-down list IQ behavior of the port (configura-
tion of pin 2)
Validation and backup Drop-down list Settings for validation and backup
for the module check in the event of
module replacement
PortCycleTime Input field Expected cycle time of the port