Product Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000Commissioning
88 Product manual | Version: 2.1.0
8PORT IOL-B FLD PN DC 24V 2.0A
Table 55: Status of the last Bluetooth® firmware update
Value Status
0 Ready for operation
1 Firmware file is being checked
2 Firmware update is being performed
Activating the Bluetooth
®
Interface Using the QR Code Displayed
Note
Never use the product in areas where operation of radio equipment is prohibited.
The product contains a radio transmitter that can impair the function of electronic medical
devices such as hearing aids and pacemakers.
Note
Only use the product with Bluetooth
®
if the product has an approval for the specific
country or region.
To enable the Bluetooth
®
interface, you must have the WAGO I/O Field app installed on
the smartphone or tablet. Proceed as follows:
• A QR appears in the “Information” section of the Bluetooth® tab. Scan it with the
smartphone or tablet.
ð The smartphone or tablet then sends an optical sequence (flash code) to the de-
vice’s integrated light sensor.
ð The light sensor registers this sequence. If the sequence is recognized as correct, the
Bluetooth
®
interface is enabled, and the product attempts to establish a Bluetooth
®
connection with the smartphone or tablet.
Starting a Bluetooth
®
Firmware Update
Proceed as follows to start a Bluetooth
®
firmware update:
1. Click Update request.
ð A dialog appears for selecting the Bluetooth
®
firmware file.
2. Select the firmware file.
ð The Bluetooth
®
firmware update starts.
Performing a Reset
Proceed as follows revert a Bluetooth
®
firmware update:
• Click Reset
ð The Bluetooth
®
firmware is reverted and restarts.
Switching the Bluetooth
®
Interface Wireless Transmitter on/off
To switch the Bluetooth
®
interface wireless transmitter on:
• Slide the Bluetooth® radio switch to the right
ð The Bluetooth
®
interface wireless transmitter switches on.