Fieldbus Independent I/O Modules End Module 750-600 Manual Version 1.0.
ii • General Copyright © 2006 by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: +49 (0) 571/8 87 – 0 Fax: +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com Web: http://www.wago.com Technical Support Phone: +49 (0) 571/8 87 – 5 55 Fax: +49 (0) 571/8 87 – 85 55 E-Mail: support@wago.com Every conceivable measure has been taken to ensure the correctness and completeness of this documentation.
Content • iii CONTENT 1 Important Comments ................................................................................. 4 1.1 Legal Principles........................................................................................ 4 1.1.1 Copyright ............................................................................................. 4 1.1.2 Personnel Qualification ....................................................................... 4 1.1.3 Intended Use .....................................
• Important Comments Legal Principles 1 Important Comments To ensure fast installation and start-up of the units described in this manual, we strongly recommend that the following information and explanations are carefully read and abided by. 1.1 Legal Principles 1.1.1 Copyright This manual is copyrighted, together with all figures and illustrations contained therein. Any use of this manual which infringes the copyright provisions stipulated herein, is not permitted.
Important Comments Symbols • 5 1.2 Symbols Danger Always abide by this information to protect persons from injury. Warning Always abide by this information to prevent damage to the device. Attention Marginal conditions must always be observed to ensure smooth operation. ESD (Electrostatic Discharge) Warning of damage to the components by electrostatic discharge. Observe the precautionary measure for handling components at risk.
• Important Comments Safety Notes 1.4 Safety Notes Warning Switch off the system prior to working on bus modules! In the event of deformed contacts, the module in question is to be replaced, as its functionality can no longer be ensured on a long-term basis. The components are not resistant against materials having seeping and insulating properties. Belonging to this group of materials is: e.g. aerosols, silicones, triglycerides (found in some hand creams).
50-600 [End Module] View • 7 2 I/O Modules 2.1 System Modules 2.1.1 750-600 [End Module] End Module 2.1.1.1 View A C B D 750-600 Fig. 2.1.1-1: End Module 750-600 2.1.1.2 g060000e Description The end module 750-600 is used to terminate the internal bus of a fieldbus node. This module completes the internal data circuit and ensures correct data flow. The end module is placed at the end of a filedbus node.
• 750-600 [End Module] Technical Data 2.1.1.4 Technical Data Module Specific Data Dimensions (mm) W x H x L 12 x 64* x 100 * from upper edge of 35 DIN rail Weight ca. 35 g Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual) EMC-Immunity to interference (CE) acc. to EN 50082-2 (96) EMC-Emission of interference (CE) acc. to EN 50081-1 (93) EMC-Immunity to interference (Ship building) acc. to Germanischer Lloyd (01) EMC-Emission of interference (Ship building) acc.
750-600 [End Module] Technical Data WAGO-I/O-SYSTEM 750 I/O Modules • 9
WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Hansastraße 27 • D-32423 Minden Phone: 05 71/8 87 – 0 Fax: 05 71/8 87 – 1 69 E-Mail: info@wago.com Internet: http://www.wago.