Fieldbus Independent I/O Modules 24 V DC Field Side Connection 750-603 Manual Version 1.0.
ii • General Copyright © 2006 by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: +49 (0) 571/8 87 – 0 Fax: +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com Web: http://www.wago.com Technical Support Phone: +49 (0) 571/8 87 – 5 55 Fax: +49 (0) 571/8 87 – 85 55 E-Mail: support@wago.com Every conceivable measure has been taken to ensure the correctness and completeness of this documentation.
Content • iii CONTENT 1 Important Comments ................................................................................. 4 1.1 Legal Principles........................................................................................ 4 1.1.1 Copyright ............................................................................................. 4 1.1.2 Personnel Qualification ....................................................................... 4 1.1.3 Intended Use .....................................
• Important Comments Legal Principles 1 Important Comments To ensure fast installation and start-up of the units described in this manual, we strongly recommend that the following information and explanations are carefully read and abided by. 1.1 Legal Principles 1.1.1 Copyright This manual is copyrighted, together with all figures and illustrations contained therein. Any use of this manual which infringes the copyright provisions stipulated herein, is not permitted.
Important Comments Symbols • 5 1.2 Symbols Danger Always abide by this information to protect persons from injury. Warning Always abide by this information to prevent damage to the device. Attention Marginal conditions must always be observed to ensure smooth operation. ESD (Electrostatic Discharge) Warning of damage to the components by electrostatic discharge. Observe the precautionary measure for handling components at risk.
• Important Comments Safety Notes 1.4 Safety Notes Warning Switch off the system prior to working on bus modules! In the event of deformed contacts, the module in question is to be replaced, as its functionality can no longer be ensured on a long-term basis. The components are not resistant against materials having seeping and insulating properties. Belonging to this group of materials is: e.g. aerosols, silicones, triglycerides (found in some hand creams).
50-603 [24 V DC Field Side Connection] View • 7 2 I/O Modules 2.1 System Modules 2.1.1 750-603 [24 V DC Field Side Connection] Field Side Connection Module DC 24 V 2.1.1.1 View 13 14 A C B D + + + + + + + + 750-603 Data contacts 24 V Power jumper contacts Fig. 2.1.1-1: Field Side Connection Module 750-603 2.1.1.
• 750-603 [24 V DC Field Side Connection] Display Elements Warning The maximum current of the field side connection module is 10 A. When configuring the system it is important not to exceed the maximum/sum current. However, if such a case should occur, another supply module must be added. The field side connection module 750-603 can be used with all couplers/controllers of the WAGO-I/O-SYSTEM 750. 2.1.1.3 Display Elements The field side connection module 750-603 has no display elements. 2.1.1.
750-603 [24 V DC Field Side Connection] Technical Data • 9 More Information Detailed references to the approvals are listed in the document "Overview Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM ELECTRONICC Tools and Docs (Item-No.: 0888-0412) or in the internet under: www.wago.
WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Hansastraße 27 • D-32423 Minden Phone: 05 71/8 87 – 0 Fax: 05 71/8 87 – 1 69 E-Mail: info@wago.com Internet: http://www.wago.