Datasheet
10
1
52,4 mm/2.06 in
81,1 mm/3.19 in
40,4 mm/1.59 in
49,4 mm/1.95 in
81,1 mm/3.19 in
40,4 mm/1.59 in
52,4 mm/2.06 in
81,1 mm/3.19 in
40,4 mm/1.59 in
52,4 mm/2.06 in
81,1 mm/3.19 in
40,4 mm/1.59 in
2000-5310/101-000
2000-5377/101-000 2000-5357/101-000
2000-5310/1101-9512000-5317/1102-950
2000-5357/102-000
2000-5317/102-000
2000-5377/102-000
PE
S
1
S
1
S2 S2
PE
PE
PE
S
1
S
1
S2 S2
PE
PE
PE
PE
S
1
S
1
S2 S2
PE
PE
PE
S
1
S
1
S2 S2
PE
PE
PE
5
Volume 1
Operating tool with partially insulated shaft,
type 1, (2.5 x 0.4)mm blade
gray
End and intermediate plate, 1mm thick,
for 3-conductor terminal blocks
Pack.
Unit
Item No.
Pack.
Unit
Item No.
Pack.
Unit
Item No.
Pack.
Unit
Item No.
Accessories for 4-Conductor Terminal
Blocks
from 1 to 10
from 1 to 9
from 1 to 8
from 1 to 7
from 1 to 6
from 1 to 5
from 1 to 4
from 1 to 3
Push-in type jumper bar, insulated,
I
N
14 A,
light gray
10-way
9-way
8-way
7-way
6-way
5-way
4-way
3-way
2-way
Push-in type jumper bar, insulated,
I
N
14 A,
light gray
plain
WMB Multi marking system,
10 strips with 10 markers per card,
for 3.5mm terminal block width
white
Marking strip, plain,
11mm wide,
50 m roll
gray
Double-deck marker carrier,
pivoting
gray gray
3-conductor actuator LED terminal block,
for NPN (negative) switching actuators, yellow LED
gray
gray
3-conductor actuator LED terminal block,
for PNP (positive) switching actuators, yellow LED,
with ground connection
orange
gray
orange
gray
gray
gray
3-conductor actuator terminal block,
for PNP (positive) switching actuators, with ground
connection
3-conductor actuator terminal block,
for NPN (negative) switching actuators
orange
orange
3-conductor actuator supply terminal block, max. 250 V,
for PNP (positive) switching actuators, with ground
connection, internal bridge
3-conductor actuator supply terminal block, max. 250 V,
for NPN (negative) switching actuators, with ground
connection
TOPJOB
®
S
3-Conductor Actuator Terminal Blocks 1 (1.5) mm²
2000 Series
L 9 … 11 mm / 0.39 in 4 L 9 … 11 mm / 0.39 in 4
Terminal block width 7 mm / 0.276 in 3 Terminal block width 7 mm / 0.276 in 3
I
N
13.5 A I
N
13.5 A
250 V/4 kV/3
2 24 VDC
0.14 …
1 (1.5) mm² 1 0.14 … 1 (1.5) mm² 1
AWG 24 … 16 AWG 24 … 16
300 V, 10 A 24 VDC, 10 A
5
4
Strip length, see packaging or instructions.
3
3.5 mm pin spacing per signal (2 x 3.5 mm = 7 mm)
2
250 V=rated voltage
4 kV=rated surge voltage
3=pollution degree
(see Full Line Catalog, Volume 1, Section 14)
See application notes in Full Line Catalog, Volume 1,
for:
Colored push-in type jumper bars, page 101
Push-in type wire jumper, page 102
1
Conductor sizes: 0.14mm² … 1.5mm² “s + f-st”;
Push-in conductor sizes: 0.5mm² … 1.5mm² “s”
and 0.5mm² … 0.75mm²
“insulated ferrule, 10mm”
WMB/Marking strips
(see Full Line Catalog, Volume 1, Section 13)
Colored push-in type jumper bars,
red
blue
yellow-green
6
Ground connection via commoning to terminal blocks
with ground foot
3-conductor actuator supply terminal block, max. 250 V,
control panel side: 2.5 (4) mm², max. 28 A, for PNP
(positive) switching actuators, with ground connection
3-conductor actuator supply terminal block, 24 VDC,
control panel side: 2.5 (4) mm², max. 28 A, for NPN
(negative) switching actuators, with ground connection
Note:
The double pin spacing of this terminal block
series allows, e.g., ten sensors to be connected
using only five sensor terminal blocks plus
power supply terminal block.
2000-5310/102-000 2000-5310/1102-950
2000-5310/101-000
2000-5317/1102-950
2000-5357/102-000
2000-5317/1101-951
2000-5357/101-000
2000-5310/1101-951
2000-5317/102-000
2000-5317/101-000
2000-5377/102-000
2000-5377/101-000
50 50
50
50
15
50
15
50
50
50
15
15
210-719
2000-5391
1
(4x25)100
2000-440
2000-439
2000-438
2000-437
2000-436
2000-435
2000-434
2000-433
2000-410
…/000-005
…/000-006
2000-409
2000-408
2000-407
2000-406
2000-405
2000-404
2000-403
2000-402
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(8x25)200
(8x25)200
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(4x25)100
(8x25)200
(8x25)200
(8x25)200
793-3501
2009-110
5
1
2000-121 (2x25)50
6
6
6
6
…/000-018