Users Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000 Planning
Product manual | Version: 2.1.0 45
8PORT IOL-B FLD PN DC 24V 2.0A
Table 33: Parameters of the “IO-Link XX I / XX O + PQI” Submodule
Parameter Group Parameters Default Value Range Description
IO-Link port parame-
ters (continued)
Validation/backup 0 0: no device check No product check oc-
curs for validation or
backup of connected
IO-Link slave prod-
ucts
1: type-compatible
device (V1.0)
A product check for
the indicated device
type is performed for
validation or backup
of connected IO-Link
slave products
2: type-compatible
device (V1.1)
3: type-compatible
V1.1 device with
backup + restore
4: type-compatible
V1.1 device with re-
store
I/Q behavior 1 0: not supported Pin 2 is not used
1: digital input Pin 2 is a digital input
2: digital output Pin 2 is a digital out-
put
5: static on High signal on pin 2
IO-Link port parame-
ters (continued)
Port cycle time - 0, 4...191 Port cycle time
0: calculated by IO-
Link master
4...191: see section
8PROFINET Pa-
rameters [}45]
Vendor ID - 0...65535 Manufacturer ID
The manufacturer ID
is used to check
whether an IO-Link
device from the right
manufacturer is con-
nected. For the value
of the manufacturer
ID, see the docu-
mentation of the sen-
sor/actuator used.
Device ID - 0...4294967295 Device ID
The device ID is
checked to see
whether the right IO-
Link device is con-
nected. For the value
of the device ID, see
the documentation of
the sensor/actuator
used.
The “Port cycle time” parameter contains a factor (bits 0 to5) and a time basis (bits 6+7).
The following table describes how the port cycle time is calculated from the factor and the
time basis.