Users Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000Connection
58 Product manual | Version: 2.1.0
8PORT IOL-B FLD PN DC 24V 2.0A
• 1L to power the logic and sensors/actuators
• 2L to power actuators (separate actuator supply)
All supply voltages are connected via L-coded M12 pluggable connectors.
!
NOTICE
Damage to electronics
Connect each of the supply voltages (each to +24V and 0V) completely. Connecting
multiple supply voltages through one 0V connection is not permitted, since this would ex-
ceed the current load capacity of the contacts.
Power Supplies 1L and 2L
The voltages 1L and 2L are electrically isolated and are fed in on connection X31.
The 1L power supply is required to power the module electronics and the connected sen-
sors/actuators. Connect it to connection X31. If you want to power additional products
through this current path, connect the cable for the additional power supply to connection
X32.
The following procedure is especially advantageous:
• Install the power supply for the module electronics independently of the power supply
for the actuators
• Provide independent fuse protection for the power supplies
This allows the network to continue to run even when peripheral parts are switched off.
!
NOTICE
Damage to electronics
The current load capacity of the L-coded M12 pluggable connector is 16A per current
path (1L or 2L). This value must not be exceeded. To limit the sum of current paths 1L
and 2L even in the event of short circuit, it may be necessary to provide fuse protection
for them. For the calculation of the maximum permissible current feedthrough, see sec-
tion 8Power Supply Examples [}38].
Note that the connection for the additional supply voltage is not monitored for overload. If
the maximum current carrying capacity is exceeded, this can damage the pluggable con-
nectors.
WAGO recommends using pre-assembled cables.
Power supply 2L is provided to power actuators. It can be used by all products that re-
quire a second separate power supply with high power. It can also be passed on to addi-
tional devices.
The following figure gives an example of feeding in and passing on the supply voltages: