Users Manual
Table Of Contents
- Table of Contents
- 1 Provisions
- 2 Safety
- 3 Overview
- 4 Properties
- 5 Functions
- 6 Planning
- 7 Transport and Storage
- 8 Installation and Removal
- 9 Connection
- 10 Commissioning
- 10.1 Setting an IP Address
- 10.2 Parameterization
- 10.2.1 PROFINET
- 10.2.2 WAGO Webserver I/O Field
- 10.2.2.1 Opening WAGO Webserver I/O Field
- 10.2.2.2 WAGO Webserver I/O Field User Interface
- 10.2.2.3 Opening the Product Information via WAGO Webserver I/O Field
- 10.2.2.3.1 Displaying Port Information
- 10.2.2.3.2 Displaying Measured Values and Information on Connected IO-Link Devices
- 10.2.2.3.3 Displaying Port Status Information
- 10.2.2.3.4 State
- 10.2.2.3.5 Quality
- 10.2.2.3.6 Revision ID
- 10.2.2.3.7 Baud Rate
- 10.2.2.3.8 Cycle Time
- 10.2.2.3.9 Input Data Length
- 10.2.2.3.10 Output Data Length
- 10.2.2.3.11 Vendor ID
- 10.2.2.3.12 Device ID
- 10.2.2.3.13 Displaying Process Data
- 10.2.2.4 Parameterizing the Product via WAGO Webserver I/O Field
- 10.2.2.4.1 Accessing a Connected IO-Link Device
- 10.2.2.4.2 Configuring Ports
- 10.2.2.4.3 Configuring IP Parameters
- 10.2.2.4.4 Storing Maintenance Information
- 10.2.2.4.5 Updating Firmware
- 10.2.2.4.6 Resetsetting the Module to the Factory Settings
- 10.2.2.4.7 Configure Bluetooth
- 10.2.2.4.8 Logging Users on and off and Managing Them
- 10.2.2.4.9 Forcing Digital Inputs and Outputs
- 10.2.2.4.10 Forcing IO-Link ports
- 10.2.3 WAGO IO-Link Configurator
- 10.2.3.1 System Requirements
- 10.2.3.2 Launching WAGO IO-Link Configurator
- 10.2.3.3 WAGO IO-Link Configurator User Interface
- 10.2.3.4 Parameterizing the Product with WAGO IO-Link Configurator
- 10.2.4 WAGO I/O Field app
- 10.2.5 OPC UA Server
- 11 Diagnostics
- 12 Service
- 13 Decommissioning
- 14 Appendix
- List of Tables
- List of Figures
765-4102/0100-0000Commissioning
94 Product manual | Version: 2.1.0
8PORT IOL-B FLD PN DC 24V 2.0A
10.2.3 WAGO IO-Link Configurator
10.2.3.1 System Requirements
The following system requirements must be met for the WAGO I/O Field configuration
software to be installed:
Minimum System Requirements
Table 57: Minimum System Requirements
Components Requirements
Operating system Windows 7 (32- and 64-bit)
Windows 8 (32- and 64-bit)
Windows 8.1 (32- and 64-bit)
Windows 10 (32- and 64-bit)
Memory 2GB
Free hard disk space 150MB
Processor 1GHz or higher, 32-bit (x86) or 64-bit (x64)
Screen resolution 800 × 600 pixels
Recommended System Requirements
Table 58: Recommended System Requirements
Components Requirements
Operating system Windows 10 (64-bit)
Memory 8GB
Free hard disk space 250MB
Processor 1GHz or higher, 64-bit (x64)
Screen resolution 1920 × 1080 pixels
10.2.3.2 Launching WAGO IO-Link Configurator
10.2.3.2.1 Operation as a Standalone Program
WAGO IO-Link Configurator can be launched as a standalone program from the Start
menu or with the desktop icon, or in connection with WAGO I/O-CHECK. It then provides
the functions necessary for connecting to accessible WAGO IO-Link masters or searching
for them.
WAGO IO-Link Configurator offers the following functions, depending on the WAGO IO-
Link master and setting:
• Diagnostics, identification, parameterization and display of process data of WAGO IO-
Link devices
• Writing output process data
This normally the controller’s job, and the tool cannot write here concurrently. How-
ever, some WAGO IO-Link masters can also be operated on the tool without a PLC. In
this case, the tool can also write the process data. In particular, this applies to some
ETHERNET-based WAGO IO-Link masters. You can tell this when the WAGO IO-Link
master opens or read about it in the corresponding documentation.
• Configuring the WAGO IO-Link master or Field I/O module