ENG Operating Manual Light Control PULSE HFMD Vers.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Dear customer, Operating panels 3 General 4 - Safety instructions 4 The operating manual informs of additional adjustment possibilities on lights with PULSE PIR-control without column operating panel MFT. The here described functions go beyond the general operation possibilities on the light and are usually rarely required.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Operating panels Sensor operating panel “PULSE HFMD” Menu structure “PULSE HFMD - Vers. IV without MFT“ Functions ON/OFF Change light level Change light level Fig. 2 Note: The functions written in blue are not available.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ General Validity of these instructions Safety instructions These instructions apply to the following lights: Make sure to read the instructions for use before putting the light into operation! Caution, Take note of the accompanying documents! Please make sure to observe the safety instructions of the light operation instructions! Important information - Lights equipped with Pulse HFMD from firmware vers. VFP 04.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Operation Fig. 4 Operating and display elements Key I + LED I Key II + LED II Sensor All operating and adjusting functions can be carried out from the sensor operation panel [fig. 4]. The functions and ajdustments are displayed at the sensor operating panel via both LEDs (I or II). In-factory setting The lights are set in-factory so that initially they can be operated without changing the settings.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Operation general Fig. 4 Key I + LED I Key II + LED II Sensor Operating elements Display Via the two keys [I and II] on the sensor, different functions can be activated depending on which key is pressed.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Operation Main functions Fig. 4 Switching on Press the switch I - the light changes to light level I. Key I + LED I Key II + LED II Sensor Press the switch II - the light changes to light level II. Switching off Briefly press the key on which the LED is lit - this will switch off the light. Change light level Briefly press the key on which the LED is not lit - this will switch the light to the other light level.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change basic settings - Part 1 Fig. 4 Change to parameterisation mode Key I + LED I Key II + LED II 8 Sensor Keep both switches [I and II] pressed simultaneously for 10 seconds. - The operating panel changes to the parameterisation mode (first to setting level 1).
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change basic settings - Part 2 Fig. 4 Key I + LED I Key II + LED II Sensor Change setting Leave parameterisation mode The LED I indicates whether a function is active (ON) or inactive (OFF) by permanent lighting or flashing, e.g.: The parameterisation mode is left if no switch has been pressed for 10 seconds. The settings are stored.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ List of functions The following functions can be selected: Fig. 4 The bold-printed values are the in-factory defaults Key I + LED I Key II + LED II Sensor Level Function LED II LED I Designation 1 Function 1.1: flashing white green Background light ON/OFF 1 Function 1.2: flashing white red External activation ON/OFF 1 Function 1.3: flashing white blue Burn-In function ON/OFF 1 Function 1.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change the basic settings - Change the setting level Fig.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change the basic settings - Setting level 1 Fig. 4 Actuation Display Press both keys for at least 10 seconds LED II flashes white Activate setting level 1 Key I + LED I Key II + LED II Sensor LED II Function 1.1 Background light ON/OFF Release both keys LED I Change function from ON to OFF or vice versa Press key I LED I Note: Note: The functions written in blue are not available.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change basic settings - Setting level 1 (continued) Fig. 4 Actuation Activate function 1.2 Key I + LED I Key II + LED II LED I Activate function 1.3 Sensor LED I Activate function 1.4 LED I Activate function 1.5 LED I Activate function 1.6 LED I Activate function 1.7 Note: The functions written in blue are not available.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change the basic settings - Setting level 2 Fig. 4 Actuation Display Press both keys once for 10 seconds and once for 5 seconds LED II flashes red Activate setting level 2 Key I + LED I Key II + LED II Sensor LED II Function 2.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change basic settings - Setting level 2 (continued) Fig. 4 Actuation Activate function 2.2 Key I + LED I Key II + LED II LED I Activate function 2.3 Sensor LED I Activate function 2.4 LED I Activate function 2.5 LED I Activate function 2.6 LED I Activate function 2.7 Note: The functions written in blue are not available.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change the basic settings - Setting level 3 Fig. 4 Actuation Display Activate setting level 3 (function 3.1 - 3.6) Key I + LED I Key II + LED II Press both keys once for 10 seconds and twice for 5 seconds LED II LED I depends on the set level Sensor Change function LED I Change function LED I Note: The functions written in blue are not available.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Change the basic settings - Setting level 4 Fig. 4 Actuation Display Activate setting level 4 (function 4.1 - 4.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 1) Fig. 4 Key I + LED I Key II + LED II Sensor Function 1.1 Function 1.2 Function 1.3 Background light External switching Burn-in function Function to switch the logo background light ON and OFF for lights with a column-operating panel (multifunctional switch). Function to operate the light via external switching elements.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 2) Fig. 4 Key I + LED I Key II + LED II Sensor Function 1.4 Function 1.5 Function 1.6 Write protection Light control Presence control Function for admission or avoidance of setting variations. Function for the automatic readjustment of the set brightness in case the ambient brightness changes. Function to detect the presence of persons. The default setting of the function is “OFF“, i.e.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 3) Fig. 4 Function 1.7 Demo mode Key I + LED I Key II + LED II Sensor Function to demonstrate and to test the light functions. The default setting of this function is “OFF“, i.e., the demo mode is inactive. All control times are working in the seconds range if the demo mode is switched on. Note: This mode is left automatically 10 minutes after the last key was pressed.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 4) Fig. 4 Key I + LED I Key II + LED II Sensor Function 2.1 Function 2.2 Function 2.3 Sensitivity high Switch-on automatic Dual sensors Function to change the sensitivity of the presence control. Function to admit or to suppress automatic switch-on with insufficient light or in case of presence (semi-automatic).
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 5) Fig. 4 Key I + LED I Key II + LED II Sensor Function 2.4 Function 2.5 Function 2.6 Sensor LED Continuous operation Parameter setting protection Function to switch both LEDs in the sensor operating panel on and off. Setting function for continuous operation. The default setting of the function is “ON“, i.e., the LEDs in the light head are switched on.
ENG Operating Manual Light Control „PULSE HFMD - Vers. IV without MFT“ Explanation of the functions (part 6) Fig. 4 Key I + LED I Key II + LED II Sensor Function 2.7 Function 3.1 - 3.6 Function 4.1 - 4.6 Special function Follow-up time Presence range The special function is not available. Function to adjust the time after which the light is to be switched off if no presence is detected. Function to set the detection range of the presence sensor. The function cannot be changed.
Order No. 405 222 110 - © copyright H.Waldmann GmbH & Co. KG - nB / 05.2011 - TB - Subject to modifications - Printed in Germany ENG 24 Operating Manual Light Control „PULSE HFMD - Vers.
