Installation and Operation Manual Gas Griddle Range Electric Oven GP8910GE GP8910GEC GP8121GE GP8121GEC GPL8910GE GPL8910GEC GPL8121GE GPL8121GEC Date Purchased Serial Number Dealer Service Provider For use in GB & IE 230560-12
MANUFACTURED BY Moffat Limited PO Box 10001 Christchurch New Zealand Ph: (03) 389 1007 Fax: (03) 389 1276 WORLD-WIDE BRANCHES UNITED KINGDOM Blue Seal 67 Gravelly Business Park Gravelly Park Birmingham West Midlands B24 8TQ Ph: (121) 327 5575 Fax: (121) 327 9711 UNITED STATES Moffat Inc 3765 Champion Blvd Winston-Salem North Carolina 27115 Ph: (336) 661 0257 Fax: (336) 661 9546 CANADA Serve Canada 22 Ashwarren Road Downview Ontario M3J1Z5 Toll Free:800 263 1455 Ph: (416) 631 0601 Fax: (416) 631 0315 info@se
Contents Waldorf Gas Griddle Electric Oven Ranges GP[L]8910GE GP[L]8910GEC GP[L]8121GE GP[L]8121GEC Gas Griddle Range Electric Static Oven Gas Griddle Range Electric Convection Oven Gas Griddle Range Electric Static Oven Gas Griddle Range Electric Convection Oven - 900 mm. - 900 mm. - 1200 mm. - 1200 mm. Introduction ............................................................................................. 2 Specifications ...............................................................................
Introduction We are confident that you will be delighted with your WALDORF GAS GRIDDLE RANGE ELECTRIC OVEN , and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Waldorf appliance, there are two important things you can do. Firstly: Please read the instruction book carefully and follow the directions given. The time taken will be well spent.
Specifications Model Numbers Covered in this Specification GP[1]8910GE GP[1]8910GEC GP[1]8121GE GP[1]8121GEC Gas Griddle Range Static Electric Oven Gas Griddle Range Convection Electric Oven Gas Griddle Range Static Electric Oven Gas Griddle Range Convection Electric Oven - 900mm. - 900mm. - 1200mm. - 1200mm. NOTE: [1]: - Back Options; - - Standard Models. L - Low Back Models.
Specifications Gas Supply Requirements - Australia / New Zealand Only: Natural Gas Input Rating (N.H.G.C.) LP Gas (Propane) GP8910GE/GEC GP8121GE/GEC GP8910GE/GEC GP8121GE/GEC 80 MJ/hr (75,825 BTU) 108 MJ/hr (102,364 BTU) 80 MJ/hr (75,825 BTU) 108 MJ/hr (102,364 BTU) Supply Pressure 1.13 - 3.40 kPa (4.5” - 13.5” w.c.) 2.75 - 4.50 kPa (11” - 18.0” w.c.) 0.90 kPa (*) (3.6”w.c.) 2.6 kPa (*) (10.2” w.c.
Specifications Electrical Supply Requirements 1-Phase Connection 1P+N+E 230-240V MODEL GP8910GE 6.5 kW, GP8121GE 26.6 Amps @ 235V GP8910GEC 6.8 kW, GP8121GEC 27.9 Amps @ 235V 3-Phase Connection 3P+N+E 400-415V L1 - 8.2 Amps 6.5 kW L2 - 9.2 Amps L3 - 9.2 Amps L1 - 9.5 Amps 6.8 kW L2 - 9.2 Amps L3 - 9.2 Amps Electrical Connection WARNING: THIS APPLIANCE MUST BE EARTHED. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
Dimensions GP[L]8910GE / GEC GP[L]8121GE / GEC 6
Installation Installation Requirements NOTE: • It is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas, electrical and health and safety requirements. • This appliance shall be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of health harmful substances in the room, the appliance is installed in.
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Left / Right Hand Side Rear Combustible Surface 50mm Non Combustible Surface 0mm 50mm 0mm Assembly C AUTIO N : • This appliance is for professional use and is to be used by qualified persons only. • Only qualified service persons are allowed to carry out installation and servicing of this appliance. This model is delivered completely assembled. Ensure that the legs are securely attached.
Installation Gas Connection NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY AN QUALIFIED PERSON. 1. It is essential that the gas supply is correct for the appliance to be installed and that adequate supply pressure and volume are available. The following checks should therefore be made before installation:a. Gas Type the appliance has been supplied for is shown on coloured stickers located above the gas connection and next to the rating plate.
Installation Electrical Connection NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY AN QUALIFIED PERSON. WARNING: THIS APPLIANCE MUST BE EARTHED. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. Each appliance should be connected to an adequately protected power supply and isolation switch mounted adjacent to, but not behind the appliance. This switch must be clearly marked and readily accessible in case of fire. 1.
Installation Commissioning Before leaving the new installation; Check the following functions in accordance with the operating instructions specified in the ‘Operation’ section of this manual. • Light the Griddle Pilot Burner. • Light the Griddle Main Burner. • Check the Griddle Low Fire Operation. • Check the Oven Heating. • Check the Oven Thermostat Operation. • Check the Oven Fan Operation (GP8910GEC and GP8121GEC Ovens Only).
Operation Operation Guide C AUTIO N : • This appliance is for professional use and is only to be used by qualified people. • Only qualified service persons are to carry out installation, servicing or gas conversion operations. • Components having adjustments protected (e.g. paint sealed) manufacturer should not be adjusted by the user / operator. 1. 2. by the Waldorf Gas Griddle Range Electric Oven have been designed to provide simplicity of operation and 100% safety protection.
Operation Lighting the Griddle - Pilots WARNING: SURFACE TEMPERATURE OF THE GRIDDLE PLATE CAN REACH OVER OPERATED AT FULL SETTING. 235°C WHEN THE APPLIANCE IS These griddles are fitted with a pilot as a standard option and Flame Failure Protection, which is incorporated by way of a thermo-electric system for each main burner. Flame Failure Protection will shut off the gas supply to that burner in the event that the pilot for that burner goes out, so that un-burnt gas is not expelled.
Operation Turning 'Off' the Griddle Main Burner / Pilot 1. 2. Turn the gas control knob clockwise to the pilot position. The main burner will extinguish and the pilot burner will remain alight. To turn 'OFF' the appliance completely, turn the gas control knob fully clockwise to the 'O' position, the pilot burner will extinguish.
Cleaning and Maintenance General C AUTIO N : Always turn off the gas and electrical supply at the mains before cleaning. This appliance is not water proof. Do Not use water jet spray to clean interior or exterior of this appliance. Clean the range regularly. A clean range looks better, will last longer and will perform better. Carbonised grease on the surface or on the griddle plate will hinder the transfer of heat from the cooking surface to the food. This will result in loss of cooking efficiency.
Cleaning and Maintenance Daily Cleaning 1. 2. 3. 4. 5. The grease drawer should be checked and emptied frequently to prevent overflow and spillage. Remove the grease drawer while still warm so that the grease is in a liquid state. Empty any grease from the drawer and wash thoroughly in the same manner as any cooking utensil. Clean the Control Panel with a damp cloth lightly moistened with a solution of mild detergent and water.
Cleaning and Maintenance Griddle - Chrome Plate Stainless Steel Surfaces a. Clean the exterior surfaces of the range with hot water, a mild detergent solution and a soft AUTIO N : scrubbing brush. Note that the gasCcontrol knobs are a push fit onto the gas control valve spindles and can be removed to allow cleaning of the front control panel. Always ensure that an even pressure is applied over the whole surface of the b.
Fault Finding This section provides an easy reference guide to the more common problems that may occur during the operation of your appliance. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section.
Wiring Schematics GP8910GE and GP8121GE 19
Wiring Schematics Wiring Diagram: GP8910GE GP8121GE 20
Wiring Schematics GP8910GEC and GP8121GEC 21
Wiring Schematics Wiring Diagram: GP8910GEC GP8121GEC 22
Gas Conversion and Specifications Conversion Procedure C AUTIO N : Ensure that the appliance is isolated from the main gas and electricity supply before commencing servicing. NOTE: • These conversions should only be carried out by qualified persons. All connections must be checked for leaks before re-commissioning the appliance. • Adjustment of components that have adjustments / settings sealed (e.g.
Gas Conversion and Specifications 8. 9. Refit the front control panel and tighten the 2 screws on the underside to secure the panel in place. Refit the control knobs to the front control panel. The control knobs are a push fit onto the shafts of the gas control valves.
Gas Conversion and Specifications Gas Regulator NOTE: The regulator supplied is convertible between Natural Gas and LPG, but it’s outlet pressure is fixed ex-factory and is NOT to be adjusted. NOTE, Pin rotated for Natural Gas NOTE, Pin rotated for LPG Fig 11 1. 2. 3. 4. Ensure that the gas supply is turned ‘OFF’ at the mains. Unscrew the hexagonal cap (23mm A/F) from the regulator.
Gas Conversion and Specifications Commissioning Before leaving the converted installation; 1. Check all gas connections for leakages using soapy water or other gas detecting equipment. WARNING: DO NOT USE A NAKED FLAME 2. 3. TO CHECK FOR GAS LEAKAGES. Check the following functions in accordance with the operating instructions specified in the ‘Operation’ section of this manual. • Light the Pilot Burner. • Light the Main Burner. • Check the Low Fire Burner operation.
Gas Conversion and Specifications Gas Specifications - Australia / New Zealand Only Natural Gas LP Gas (Propane) GP8910GE/GEC GP8121GE/GEC GP8910GE/GEC GP8121GE/GEC Griddle Main Burner Pilot Burner Low Fire Adjustment High Fire Adjustment Operating Pressure 3.00mm 2.85mm 1.80mm 1.70mm 0.41 0.25 1 full turn counter clockwise from the Fully ‘IN’ position Maximum Flow Screw. Fully ‘IN’ (Note 1) 0.90 kPa (Note 2) 2.
Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on the reverse of the front cover of this manual).
Replacement Parts List General 227892 227893 227896 228400 227850 229674 Oven Side Rack LH. Oven Side Rack RH. Oven Rack. Grease Drawer. Adjustable Legs. Rear Roller Assy. Griddle Plate Options Griddle Plate Standard Chromed-(C) 900mm PGH920 PGH920C 1200mm PGH1220 PGH1220C Ribbed & Chromed Options ON REQUEST (depending on ribbed section width on LH or RH side). Accessories 228566 228567 233817 228800 228804 Griddle Scraper Tool.
30
