Installation and Operation Manual Gas Range Convection Oven RN8510GC RNL8510GC RNB8510GC RNLB8510GC RN8610GC RNL8610GC RNB8610GC RNLB8610GC RN8810GC RNL8810GC RNB8810GC RNLB8810GC Date Purchased Serial Number Dealer Service Provider For use in GB, IE & DK 228680-24
MANUFACTURED BY Moffat Limited Rolleston 7675 New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited Web: E.Mail: Main Office: Service: Spares: Customer Service: www.moffat.com.au vsales@moffat.com.au (tel) +61 (03) 9518 3888 (fax) +61 (03) 9518 3833 (tel): 1800 622 216 (tel): 1800 337 963 (tel): 1800 335 315 (fax): 1800 350 281 CANADA Serve Canada Web: E.Mail: Sales: Service: www.servecanada.com info@servecanada.
Contents Waldorf Gas Convection Oven Range RN(L)(B)8510GC RN(L)(B)8610GC RN(L)(B)8810GC Gas Range Convection Oven - 750mm wide. Gas Range Convection Oven - 900mm wide. Gas Range Convection Oven - 1200mm wide. Introduction .............................................................................................. 2 Specification ..............................................................................................
Introduction We are confident that you will be delighted with your WALDORF Gas Range Convection Oven, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Waldorf appliance, there are two important things you can do. Firstly: Please read the instruction book carefully and follow directions given. The time taken will be well spent.
Specifications Model Numbers Covered in this Specification RN[1]8510GC [2] Gas Range Convection Oven + 4 Open Burners. RN[1]8513GC [2] Gas Range Convection Oven + 2 Open Burners + 300mm Griddle. RN[1]8610GC [2] Gas Range Convection Oven + 6 Open Burners. RN[1]8613GC [2] Gas Range Convection Oven + 4 Open Burners + 300mm Griddle. RN[1]8616GC [2] Gas Range Convection Oven + 2 Open Burners + 600mm Griddle. RN[1]8619GC Gas Range Convection Oven + 900mm Griddle.
Specifications Gas Supply Requirements - Australia: Natural Gas LP Gas (Propane) - each Open Burner 28 MJ/hr 28 MJ/hr - each 300mm Griddle Section 21 MJ/hr 21 MJ/hr - Oven 30 MJ/hr 30 MJ/hr 1.13 - 3.40 kPa 2.75 - 4.50 kPa 0.95 kPa 2.6 kPa Input Rate (N.H.G.C.) Supply Pressure Burner Operating Pressure (*) 3 Gas Connection /4” B.S.P.
Specifications - All Other Markets: Natural Gas Town Gas (**) - each Open Burner 28MJ/hr 28MJ/hr - each 300mm Griddle Section 21MJ/hr 21MJ/hr - Oven 30 MJ/hr 30 MJ/hr 1.13 - 3.40kPa 0.75 - 1.50kPa 0.95kPa 0.63 Pa Input Rate (N.H.G.C.) Supply Pressure Burner Operating Pressure (*) Gas Connection See ‘Gas Connection’ information overleaf LP Gas (Propane) Butane 28MJ/hr 28MJ/hr - each 300mm Griddle Section 21MJ/hr 21MJ/hr - Oven 30 MJ/hr 30 MJ/hr 2.75 - 4.50kPa 2.75 - 4.50kPa 2.
Dimensions RN(L)8510GC Cooktop Options RN(L)8513GC RN(L)8510GC 6
Dimensions RN(L)8610GC Cooktop Options RN(L)8610GC RN(L)8613GC RN(L)8616GC RN(L)8619GC 7
Dimensions RN(L)8810GC Cooktop Options RN(L)8810GC RN(L)8813GC RN(L)8816GC RN(L)8819GC 8
Installation Installation Requirements NOTE: It is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas, electrical and health and safety requirements. This appliance shall be installed with sufficient ventilation to prevent occurrence of unacceptable concentrations of health harmful substances in room, appliance is installed in.
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Left / Right hand side Rear Combustible Surface 250mm (*) 100mm Non Combustible Surface 0mm 0mm * Side clearances can be 50mm when the adjacent surface is at least 100mm below cooking surface. Assembly Caution This appliance is for professional use and is only to be used by qualified persons.
Installation Regulator connections are 3/4" BSP female. Connection to the appliance is 3/4" BSP male. (Refer to ‘Specifications’ section for gas supply location dimensions). NOTE: A Manual Isolation Valve must be fitted to individual appliance supply line. 3. 4. 5. Correctly locate appliance into its final operating position and using a spirit level, adjust legs so that appliance is level and at correct height. Connect gas supply to appliance.
Operation Operation Guide Caution This appliance is for professional use and is only to be used by qualified persons. Only authorised service persons are to carry out installation, servicing or gas conversion operations. Components having adjustments protected (e.g. paint sealed) manufacturer should not be adjusted by the user / operator. 1. 2. by the Waldorf appliances have been designed to provide simplicity of operation and 100% safety protection.
Operation Open Burners ('F' - Flame Failure Option) Lighting the Open Burners Flame Failure Protection is incorporated for each burner by way of a thermo-electric system which will shut off gas supply to that burner in the event that burner goes out, so that un-burnt gas is not expelled. a. Select burner required, depress and turn the gas control knob anti-clockwise to ‘HIGH’ position. b. Hold gas control knob depressed and manually light main burner. c.
Operation Griddle Lighting the Griddle a. Depress gas control knob and rotate anti-clockwise to ‘PILOT’ position. b. Hold gas control knob depressed, press piezo ignition button to ignite pilot burner. Repeat Items 1 to 2 until pilot is lit. c. Release gas control knob approximately 10-20 seconds after lighting pilot. d. Pilot should now remain alight - if not, repeat Steps (b. to (c. above. e. To select ‘Full Flame’, depress and rotate gas control knob anti-clockwise to ‘HIGH’ position. f.
Operation Oven - Main Burner / Thermostat 1. 2. 3. 4. 5. 6. Ensure oven door is closed. Turn ‘ON’ electrical power at mains supply, (green) power indicator light will illuminate on oven control panel. With pilot burner alight, depress and rotate oven gas control knob to 'Main Flame' position. (This puts gas valve in 'Stand-By' position and control of main burner is now carried out through oven thermostat control).
Cleaning and Maintenance Before Commencing Cleaning Caution Always turn off the gas / electrical supply before cleaning the appliance. This appliance is not water proof. Do not use water jet spray to clean interior or exterior of this appliance. NOTE: Allow appliance to cool before commencing cleaning. DO NOT use abrasive or strong caustic detergents as they could corrode or damage the Cooktop. Ensure that any detergent or cleaning material has been completely removed after each cleaning.
Cleaning and Maintenance Open Burner Cleaning Griddle Plate Cleaning 1. Remove pot stands, burner caps, burner bowls and pot stand supports from top of cooktop. Wash with hot soapy water, using a soft bristled brush. Dry thoroughly with a dry cloth. Any baked-on deposits can be scraped off using a scraper tool. It is recommended that a flat blade scraper is used to clean the griddle surface, these are not supplied with griddle but may be purchased separately.
Cleaning and Maintenance Oven Interior Cleaning 1. Do not use wire brushes, steel wool or other abrasive materials to clean oven interior. 2. Clean oven regularly with a good quality domestic oven cleaner. 3. Weekly - Remove and clean any built up of grease etc. from oven racks and bottom spill cover. 4. Dry oven thoroughly with a dry cloth and polish with a soft dry cloth. Stainless Steel Surfaces 1. Clean stainless steel surfaces with hot soapy water and a soft bristled brush. 2.
Fault Finding This section provides an easy reference guide to more common problems that may occur during operation of your appliance. This fault finding guide is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section.
20 7 5 4 9 5 1 2 COM 003004 MICROSWITCH 5 POWER GREEN 11987 THERMOSTAT 2 P5 2 1 N.O.
Gas Conversion and Specifications Conversion Procedure Caution Ensure that the Appliance is isolated from the gas supply before commencing servicing. NOTE: These conversions should only be carried out by qualified persons. All connections must be checked for leaks before re-commissioning the appliance. Adjustment of components that have adjustments / settings sealed (e.g. paint sealed) can only be adjusted in accordance with the re-commissioning this appliance.
Gas Conversion and Specifications Piezo Igniter Griddle 1. Pilot Supply Tube Carry out the following: Remove griddle plate section and heat shield. Remove main burner. Disconnect piezo igniter from mounting bracket. (For access purposes). Pilot Burner Disconnect pilot supply tube from pilot burner to access pilot injector. Main Burner Injector 2.
Gas Conversion and Specifications 3. Remove pilot and main injectors and replace with correct size injectors as shown in ‘Gas Specifications Tables’ at end of this section. 4. Refit the following: Re-connect pilot supply tube to pilot burner. Re-connect piezo igniter and thermocouple to mounting bracket. Refit main burner and secure clamp bracket. Refit sole plate(s) and lower lintel. NOTE: There is no 'Low Fire' adjustment on the gas control valve for the GC Oven.
Gas Conversion and Specifications Gas Specifications - Australia: Open Burner Griddle Oven Main Burner Injectors Pilot Burner ('PF' Option Only) Main Burner Pilot Burner Burner Aeration Setting Main Burner Pilot Burner Burner Aeration Setting Supply Pressure Burner Operating Pressure (*) Natural Gas LP Gas (Propane) Ø 2.45mm 0.30 Ø 2.10mm 0.35 Fully Open Ø 2.60mm 0.35 Fully Open 1.13 - 3.40 kPa 0.95 kPa Ø 1.50mm 0.20 Ø 1.30mm 0.23 Fully Open Ø 1.60mm 0.23 Fully Open 2.75 - 4.50 kPa 2.
Gas Conversion and Specifications - UK Only: Category: Flue Type: Open Burner II2H3P (20, 37). A1. Natural Gas (G20) Propane (G31) Ø 2.30mm Ø 1.40mm 0.30 0.20 Ø 2.10mm 0.35 Fully Open Ø 2.60mm 0.35 Fully Open 20 mbar 9.5 mbar Ø 1.30mm 0.23 Fully Open Ø 1.60mm 0.
Gas Conversion and Specifications - All Other Markets: Open Burner Natural Gas Town Gas (**) Ø 2.45mm Ø 4.50mm 0.30 0.60 Ø 2.10mm Ø 3.40mm Main Burner Pilot Burner ('PF' Option Only) Main Burner Griddle Pilot Burner 0.35 0.60 Fully open Fully open Main Burner Ø 2.6mm Ø 5.0mm Pilot Burner 0.35 0.60 Fully Open Fully Open 1.13 - 3-4 kPa 0.75 - 1.50 kPa 0.95 kPa 0.
Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for servicing and repair of this appliance. Instructions supplied with parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on reverse of front cover of this manual). When ordering replacement parts, please quote the part number and the description as listed below.
Replacement Parts List Oven 232233 227933 018691K 020253 018743 Knob Thermostat Oven Burner. Oven Pilot Burner Kit. Oven Thermocouple Thermocouple Spacer. 032260 032160 032145 032500 Burner Burner Burner Burner 026488 019217 018067 011987 230312 227508 018744 019407 019479K 010866 228116 010909 013586 228704 227963 227962 228938 230075 230268 748001 044018 (80-300°C). (1200mm). Injector Injector Injector Injector (Nat Gas) (LPG) (Butane) (Towns Gas) Ø Ø Ø Ø 2.60mm. 1.60mm. 1.45mm. 5.00mm.
Replacement Parts List Gas Regulators Gas Type Gas Regulators Description Part No. Nat. Gas LPG Butane 228531 ¾” BSP F/F Convertible. Town Gas 230185 ¾” BSP F/F Adjustable. Gas Conversion Kits 'PF' Models 'F' Models Models Gas Type to Convert to Nat. Gas LPG Butane Town Gas Nat.
