Item #: BWSTOT Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com or call us at 877-207-5906.
Instruction Manual IMPORTANT INFORMATION READ BEFORE ASSEMBLING THIS PRODUCT Follow the information on the warning labels found on the bunk bed and on the packaging. Do not remove the warning label from the bed. Use only a mattress with the dimensions 74-75 in. L x 37.5-38.5 in. W x 6 in. H on the upper bunk. A mattress with the same dimensions is also recommended for the lower bunk. The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the guardrails.
Parts List
Hardware List Wood joint connector Wood joint connector Flat head wood screw Flat head wood screw Wood dowel Wood dowel Hex key
Assembly Options Twin over Twin Bunk Bed Conversion into Two Single Twin Beds
Insert wood dowels (7) into slats (F,S,G). Insert wood dowels (7) into guardrails (M,N) and ladder rungs (Q).
Attach legs (A,B) to slats (F,S,G) using wood joint connectors (3). Attach legs (A,C) to slats (F,S,G) using wood joint connectors (3). Only two wood joint connectors (3) will be used at each leg. Attach first set of legs (D,E) to slats (F,S,G) using wood joint connectors (3). Attach second set of legs (D,E) to slats (F,S,G) using wood joint connectors (3). Insert wood dowels (6) into both sets of legs (D,E).
I Insert barrel nuts (8) into crossbeams (I,K). Attach crossbeams (I,K) to first set of legs (D,E) using joint connectors (1). Joint connectors (1) will screw into barrel nuts (8). I Insert barrel nuts (8) into crossbeams (I,K). Attach second set of legs (D,E) to crossbeams (I,K) using joint connectors (1).
Secure mattress supports (L) to the bed assembly from the previous step using flat head wood screws (4). Use spacers (U) as guides to space mattress supports (L) evenly. Insert barrel nuts (8) into crossbeams (H,J). Attach crossbeams (H,J) to legs (A,C) using joint connectors (1). Joint connectors (1) will screw into barrel nuts (8). Secure guardrails (M) to leg (A) using wood joint connectors (3).
Insert barrel nuts (8) into crossbeams (H,J). Attach legs (A,B) to crossbeams (H,J) using joint connectors (1). Secure guardrails (M) to leg (B) using wood joint connectors (3). Secure mattress supports (L) to the bed assembly from the previous step using flat head wood screws (4). Use spacers (U) as guides to space mattress supports (L) evenly.
J M M H Attach guardrails (N) to leg (A) using wood joint connectors (3). Attach first guardrail support (R) to crossbeam (H) and guardrails (N) using flat head wood screws (5). Attach second guardrail support (R) to crossbeam (J) and guardrails (M) using flat head wood screws (5). To build the ladder, attach ladder side rails (O,P) to ladder rungs (Q) using wood joint connectors (2).
6 6 6 6 Carefully lift and place the upper bunk assembly onto the lower bunk assembly using wood dowels (6) as guides.
I Attach the ladder to the bunk bed assembly using wood joint connectors (2).
Option B Conversion into Two Single Twin Beds
Loosen the appropriate hardware and remove the ladder from the bunk bed assembly.
Carefully lift the upper bunk off of the lower bunk.
B A A C Loosen the appropriate hardware of the upper bunk so that the guardrails and leg assemblies are no longer connected to the bed assembly.
Insert barrel nuts (8) into either end of crossbeams (H,J). Attach legs (A,B) and legs (A,C) to crossbeams (H,J) using joint connectors (1). Joint connectors (1) will screw through the bottom set of holes on each leg and into barrel nuts (8).