Item #: BTLD46SP Assembly Instructions Revised 06/2012
Instruction Manual IMPORTANT INFORMATION READ BEFORE ASSEMBLING THIS PRODUCT Follow the information on the warning labels found on the bunk bed and on the packaging. Do not remove the warning labels from the bed. Use only a mattress with the dimensions 74-75 in.L x 37.5-38.5 in.W x 6 in.H on the upper bunk. The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the guardrails. Mattress must not exceed the maximum thickness of 6 in.
Parts List
Hardware List
Assembly Options Option A - Ladder Left To build this option follow Steps 1-8, Steps 10A-13A and Steps 14-23. Skip Step 9 for this assembly option. Option B - Ladder Right To build this option follow Steps 1-8, Step 9, Steps 10B-13B and Steps 14-23.
Attach guardrail (10) and shelf supports (8) to posts (1,4) using bolts (A). Tighten bolts (A) with wrench (G). Please note the position of all pre-drilled holes as shown above before attaching bed parts together. Attach second guardrail (10) posts (2,3) using bolts (A). Tighten bolts (A) with wrench (G). Please note the position of all pre-drilled holes as shown above before attaching bed parts together.
Attach crossbar (5) to post (1) and crossbar (6) to post (4) using bolts (A). Tighten bolts (A) with wrench (G). Please note the position of all pre-drilled holes as shown above before attaching bed parts together. Attach opposite end of crossbar (5) to post (2) and opposite end of crossbar (6) to post (3) using bolts (A). Tighten bolts (A) with wrench (G).
Roll mattress support slats (11) out along the bed frame and secure them to the bed frame using anchors (F) and bolts (A) where indicated above. Bolts (A) will screw directly into crossbars (5,6). Tighten bolts (A) with wrench (G). Attach guardrail (9) to posts (3,4) using bolts (A). Secure guardrail (9) to crossbar (6) using bolts (B). Tighten bolts (A,B) with wrench (G).
Attach second guardrail (9) to posts (1,2) using bolts (A). Secure guardrail (9) to crossbar (5) using bolts (B). Tighten bolts (A,B) with wrench (G). Attach shelf supports (12) to rails (7) using bolts (A). Tighten bolts (A) with wrench (G).
Attach ladder rungs (13) to post (1) using bolts (A). Tighten bolts (A) with wrench (G). Attach the shelf support assembly from Step 7 to ladder rungs (13) using bolts (B). Rail (7) will attach directly to ladder rungs (13). Tighten bolts (B) with wrench (G).
Secure rails (7) to crossbars (5,6) using bolts (A). Tighten bolts (A) with wrench (G). Attach shelves (14) to the bed frame using bolts (D). Four bolts (D) will be used to attach each shelf. Tighten bolts (D) with wrench (G).
Rotate bed frame so posts (3,4) are at the front and posts (1,2) are at the back.
Attach ladder rungs (13) to post (4) using bolts (A). Tighten bolts (A) with wrench (G). Attach the shelf support assembly from Step 7 to ladder rungs (13) using bolts (B). Rail (7) will attach directly to ladder rungs (13). Tighten bolts (B) with wrench (G).
Secure rails (7) to crossbars (5,6) using bolts (A). Tighten bolts (A) with wrench (G). Attach shelves (14) to the bed frame using bolts (D). Four bolts (D) will be used to attach each shelf. Tighten bolts (D) with wrench (G).
Attach desk support (18) to desk post (15) using bolt (A). Tighten bolt (A) with wrench (G). Attach desk crossbar (20) to desk post (15) using double-ended bolt (E). Please note the position of all pre-drilled holes as shown above before attaching desk parts together. Attach opposite end of desk support (18) to desk post (16) using bolt (A). Attach opposite end of desk crossbar (20) to desk post (16) using bolt (C). Tighten bolts (A,C) with wrench (G).
Attach desk support (19) to desk post (15) using bolt (A). Tighten bolt (A) with wrench (G). Attach desk crossbar (20) to desk post (15) using double-ended bolt (E). Please note the position of all pre-drilled holes as shown above before attaching desk parts together. Attach opposite end of desk support (19) to desk post (17) using bolt (A). Attach opposite end of desk crossbar (20) to desk post (17) using bolt (C). Tighten bolts (A,C) with wrench (G).
Screw wheels (24,25) into desk posts (15,16,17). Use wrench (H) to tighten the connection of wheels to posts. Attach desk crossbar (22) to desk post (16) using bolts (A). Tighten bolts (A) with wrench (G).
Attach desk crossbar (21) to desk support (18) using bolt (B). Attach desk crossbar (23) to desk post (16) using bolt (C). Tighten bolts (B,C) with wrench (G). Attach opposite end of desk crossbar (21) to desk support (19) using bolt (B). Attach opposite end of desk crossbar (22) to desk post (17) using bolts (A). Attach opposite end of desk crossbar (23) to desk post (17) using bolt (C). Tighten bolts (A,B,C) with wrench (G).
Attach desk top (26) to desk supports (18,19) using bolts (D). Tighten bolts (D) with wrench (G).
