W44CFDBL, W44CFDMB ASSEMBLY INSTRUCTIONS For our most up-to-date instructions, to request missing, lost, or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com or call us at 1-877-207-5906.
For our most up-to-date instructions, to request missing, lost, or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com or call us at 1-877-207-5906.
W44CFDBL, W44CFDMB Parts List 3
W44CFDBL, W44CFDMB Hardware List * The hardware quantities listed are required for proper assembly. Some extra hardware may have also been included.
Step 1 Step 2 Insert dowels (C) and cam bolts (B) into side panels (3 & 4). (Apply glue (D) to dowels as directed in the “General Assembly Guidelines”) Attach the legs (5,6,7,8) to the side panels (3 & 4) as shown in the diagram. Tighten cam locks (A) using a screwdriver as shown. Set aside for later use. Attach support leg (11) to the stand base (2) with screws (E) using hex wrench (F). Attach divider panel (10) to the stand base with screws (E) using hex wrench (F).
Step 3 Step 4 Attach cam bolts (B) to the middle shelf (9) as shown in the diagram. Cover cam locks (A) using the provided stickers as shown in the diagram. Insert dowels (C) into the left side panel (3). (Remember to apply glue (D)) Insert cam locks (A) into frame assembly. Attach middle shelf (9) to frame assembly. Tighten cam locks (A) with a screwdrivers as shown in the diagram.
Step 5 Step 6 C Attach cam bolts (B) to side panel assemblies (3 & 4). Cover cam locks (A) using the provided stickers as shown in the diagram. Insert dowels (C) into the left side panel (3). (Remember to apply glue (D)) Insert cam locks (A) into frame assembly. Attach left side panel (3) to frame assembly. Tighten cam locks (A) with a screwdrivers as shown in the diagram.
Step 7 Step 8 Insert dowels (C) into frame assembly. (Remember to apply glue (D)) Attach supports (12,13) to the frame assembly as shown in the diagram. Slide back panel (14) into the grooves as shown in the diagram. Be sure that the side with the warning label is facing outward.
Step 9 Step 10 V Insert dowels (C) into frame assembly (remember to apply glue (D)). Insert cam locks (A) into frame assembly. Attach right side assembly (4) to the frame assembly. Tighten cam locks (A) using a screwdriver as shown in the diagram. Attach block (17) to the stand top (1) using screws (V). Screw cam bolts (B) into stand top (1), then attach door stop (G) using screws (H) as shown in the diagram. Be sure to tighten firmly.
Step 11 Step 12 1 Insert the plastic pivots (Q) into the stand as shown in the diagram. Insert dowels (C) into frame assembly. (Remember to apply glue (D)) Insert cam locks (A) into frame assembly. Attach stand top (1) to the frame assembly. Tighten cam locks (A) using a screwdriver as shown in the diagram. Place provided stickers over cam locks (A).
Step 13 H H I H H J Attach door handles (N) to the stand doors (15,16) using screws (P). Attach screws (K) to the corners of each door as shown in the diagram. Attach hinge (J) to door (15) as shown in the diagram. Attach hinge (I) to door (16) as shown in the diagram. Insert lower door hinges (I, J) into the lower pivot points. Attach doors (15,16) to the stand at the upper pivot points as shown in the diagram. Attach doors to lower door hinges (I, J) using screws (H).
Step 14 Insert plastic wedges (R) between the stand frame and the back panel as shown in the diagram. Fasten plastic wedges to the back panel using screws (S).
