VF13003 ASSEMBLY INSTRUCTIONS CLASSIC VINYL PICKET FENCE (4’H X 7’W) ASSEMBLY INSTRUCTIONS VF13003 60 MIN Approximate assembly time Want to see a video on how to assemble this product? Scan the QR code WWW.WAMBAMFENCE.COM WWW.WAMBAMFENCE.COM 1 VER.
VF13003 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
VF13003 ASSEMBLY INSTRUCTIONS AVOID THESE PITFALLS! HAVE YOU CONTACTED YOUR LOCAL UTILITIES? 1 You must call your local utilities before you start installing your fence to avoid puncturing any unseen underground utilities, especially electrical or gas lines. Fortunately, this is made easy for you. k Simply call 811 in the US or visit www.call811.com. k In Canada, visit www.transcanada.com/contactus.html for a list of phone numbers by province.
VF13003 ASSEMBLY INSTRUCTIONS TOOLS AND MATERIALS YOU’LL NEED Safety Glasses 1ft. Torpedo Level 4ft. Level (optional String Line Level) 2in. x 2in. x 6in. Inch Wood “Spacer” Block (2 for each panel) Cordless Drill (preferably with a high-torque setting) Auger (optional) Shovel (optional) Any Power Or Hand Saw With A FineToothed Blade String Line Stakes Spool of String Tape Measure 4 WWW.WAMBAMFENCE.
ASSEMBLY INSTRUCTIONS VF13003 MURPHY’S VINYL FENCE LAWS LET’S PRETEND (JUST FOR A MOMENT) THAT YOU LIVE IN A PERFECT WORLD. To get started, we are going to walk you through how you would install the fence illustrated below. This is the perfect scenario with no curve balls. The ground is level, your fence sections all work out evenly, the birds are chirping, and the sky is blue. Now back to reality. Your situation is almost guaranteed not to be like this. That’s why we created “Murphy’s Vinyl Fence Laws”.
VF13003 ASSEMBLY INSTRUCTIONS This fence can be trimmed down both in width and height to accommodate custom applications. Top View 4.5in. 4.5in. 3.5in. Screw 3in. 2.9in. 1.5in. 6in. 3.5in. 72in. 48in. 3.5in. .090in. Wall Thickness 32in. 1.5in. 2in. 4.5in. 4.5in. Concrete Footing 2in. 79.5in. Ground .090in. Wall Thickness 22.5in. 36in. 10in. 6 WWW.WAMBAMFENCE.
VF13003 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B G Post Cap (1) Top Rail (1) 1½” x 3½” x 81½” C D 3½” Self-Drilling Stainless Steel Screw (4) H Post (1) 4½” x 4½” x 72” E Picket Cap (13) 1¼” Self-Drilling Stainless Steel Screw (4) F I Picket (13) ⅞” x 3” x 42½” WWW.WAMBAMFENCE.
VF13003 ASSEMBLY INSTRUCTIONS STEP 2: INSTALL POSTS STEP 2.1 STEP 2.2 After stringing your fence line, dig your first post hole 10” diameter x 36” deep. Dig your second hole 84” center to center to your first hole. Dig only three or four holes at a time to ensure proper spacing. Add approximately 18” of concrete to the bottom of the hole. Then, install Posts (C) straight and level. Add more concrete to within 2” of ground level. C 10” 79½” 2” 84” 36” STEP 3: INSTALL RAILS AND PICKETS STEP 3.
VF13003 ASSEMBLY INSTRUCTIONS STEP 3.4 Drive (4) 1¼” Self-Drilling Stainless Steel Screws (H) through the middle of the top rail and upper cavity of the bottom rail as illustrated. The height of the rails can now be adjusted as needed. H STEP 3.5 Drive a 3½” Self-Drilling Stainless Steel Screw (G) through the posts into the rails. Note: Do not over-tighten the 3½” self-drilling stainless steel screws because it will cause the vinyl to dimple.
VF13003 ASSEMBLY INSTRUCTIONS STEP 3.6 Repeat in each remaining rail corner using (3) total 3½” self-drilling stainless steel screws. Note: This step will ensure that your fence rails will never fall out of your posts like traditional vinyl fence rails sometimes do. STEP 4: INSTALL PICKET AND POST CAPS STEP 4.1 Use the provided Tube of Glue (I) to attach the Picket Caps (D) onto the top of the pickets. I 10 D WWW.WAMBAMFENCE.
VF13003 ASSEMBLY INSTRUCTIONS STEP 4.2 1. Put a small bead of vinyl glue or weld along the inside of the Post Cap (A). 2. Place the glued post cap on the post and allow to set for 5-10 minutes. Vin yl W 1 WWW.WAMBAMFENCE.
VF13003 ASSEMBLY INSTRUCTIONS CUSTOMIZE YOUR FENCE DESIGN Use the cutting guide below to trim pickets to create a custom fence design. A B C D E A B C D E D C B A F G F E F G E D C B A F A B C D E F G 441/4” 423/8” 407/8” 393/4” 387/8” 383/8” 381/4” A B C D E F G 381/4” 411/2” 42” 423/4” 431/2” 44” 441/4” Most yards are relatively level and will allow for a fairly simple installation.
VF13003 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 hmmm@wambamfence.com 704-892-5222 877-778-5733 WWW.WAMBAMFENCE.COM WWW.WAMBAMFENCE.
