Classic Vinyl Picket Gate REALLY Important stuff to know about installing your WamBam gate. 1-877-778-5733 www.wambamfence.
Classic Picket Vinyl Gate Reality Check 1 - Read Over Fence Instructions First Your gate and fence will work better together as an integrated solution if you first take the time to read and understand your fence instructions. 2 - Do a Dry Run First on the Gate Frame Only (not pickets or boards) Please do not glue or screw your gate frame together until you have first temporarily assembled the gate. In other words, do a dry run first.
Classic Vinyl Picket Gate 4 - Ideally, Do Not Hang Your Gate System Off a Single Non-Supported Post. Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is connected to another post. The weight strain will be transferred unto two posts versus just one. Installing fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space restrictions, please contact us for alternative solutions to overcome.
Classic Vinyl Picket Gate PRODUCT OVERVIEW Gate Assembly Gate Installation 2.89in. 3in. 48in. A 3.5in. 4in. 48in. C 47.5in. 50.5in. D 24.75in. 72in. 2in. 7.75in. 3.5in. B Ground 2in. Concrete Footing 48in. 50in. A C B 1.5in. 3.5in. 1.5in. 3.5in. 1.5in. Posts Sold Separately D 3.5in. 36in. 1.5in. 3.5in. 10in. .090in. wall thickness For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate Box Contents Each Gate Box Includes: .050in. wall thickness • Gate Caps (2) .090in. wall thickness • T-Brackets (2) • Gate Hinges (2) • Picket Caps (7) • Top Rail (1) • Gate Latch (1) • Vertical Stiles (2) • Pickets (7) • Stainless Steel Screws (20) • Gate Brace (1) • Bottom Rail (1) • Tubes of Glue (2) • Gate Bottom Brackets (2) Sold Separately: • 6ft. Posts (2-Pack) Posts Sold Separately as 2-Packs. For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate Customize Your Gate Design Use The Cutting Guide Below To Trim Pickets to Create A Custom Gate Design B A C D C This Gate Can Also Be Trimmed Down Both in Width and Height to Accomodate Custom Applications. B A A B C D 37 1/8in. 40 3/8in. 42 3/8in. 43 1/8in. Please Note: Cut down the vertical stiles by 6in. For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate Detailed Installation Instructions STEP 1 Assemble the Gate Frame Bottom & Sides A Handle with care: vinyl weld glue takes approximately five minutes to cure. UE GL Completely assembled gate shown B A - Run bead of vinyl weld continously around the inside of the gate bracket Did you do a dry run of assembly first? Please read page 1 of instructions. Note that the bottom rail is ribbed internally. Insert fully to this point.
Classic Picket Vinyl Gate STEP 2 Assemble the Gate Frame Top & Attach to Sides A B Did you do a dry run of assembly first? Please read page 1 of instructions.
Classic Picket Vinyl Gate STEP 3 Screw Gate Frame/Brackets A 48in. A - ENSURE YOUR GATE IS SQUARE and screw brackets as illustrated. The corner-to-corner measurement must be the same, and the width of the gate should be 48”.
Classic Picket Vinyl Gate STEP 4 Insert Pickets Into Gate Frame & Attach Caps A B E LU G A - Insert pickets with tab ends through top rail C B - Glue picket caps and attach to top of pickets D E LU G C - Glue bracket caps and attach to top of brackets D - Completed gate with frame shown For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate STEP 5 Fasten Gate Hinges & Gate Latch A Latch and hinges must be installed in these exact locations. A - Fasten gate hinges and gate latch onto the gate brackets with screws For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate STEP 6 Assemble & Fasten Gate Brace B A Gate Brace Parts (2) .25” x .75” Hex Bolts (2) .25” Lock Washers (2) .25” Nuts (4) 1.25” (#10) Screws 1 Top Bar Bottom Bar 2 3 A - Assemble gate bace with bolts, washers and nuts as necessary. B - Re-confirm the gate is square, and screw bracing into place. For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate Position, Adjust & Align Gate/ STEP 7 Secure Hinges to Posts A A - Use temporary spacers or blocks to rest the gate on during alignment and installation B B - Fasten hinges to posts with screws For more information, contact us at 1 877-778-5733.
Classic Picket Vinyl Gate STEP 8 Level Gate & Adjust Hinges A B LEVEL A - Fasten gate hinges accordingly C Adjust the spring tension in gates as necessary. Use steel insert pin. C - Hinges can be adjusted moderately to bring gate into level alignment with post B - Check for level, fit and function to latching post D Latch is designed for left and right hand applications. Temporarily remove the spring, bolt and reverse paddle portion as necessary.
Classic Picket Vinyl Gate STEP 9 Align & Install Latch A A - Align and fasten the gate latch catch to fit and function with the gate finger. B Congratulations! You did it! Go grab a beverage of your choice, admire your handy work, and show us what you got by entering our annual photo/video contests! For more information, contact us at 1 877-778-5733.
