Water-proof Wired/ Wireless IP Camera User Manual Model: IPCAM01 Model: IPCAM02
IPCAM User Manual Contents 1 WELCOME ............................................................................................................................... - 1 1.1 Features ................................................................................................................................ - 1 1.2 Packing List.......................................................................................................................... - 2 1.3 Product views ..................................
IPCAM User Manual 4.1.9 Problems of using the firefox browser .....................................................................- 31 4.2 Default Parameters ..............................................................................................................- 34 4.3 Specification........................................................................................................................- 35 5 OBTAINING TECHNICAL SUPPORT .................................................................
IPCAM User Manual 1 WELCOME IPCAM is an integrated wireless IP Camera solution. It combines a high quality digital video Camera with network connectivity and a powerful web server to bring clear to your desktop from anywhere on your local network or over the Internet. The basic function of IPCAM is transmitting remote video on the IP network. The high quality video image can be transmitted with 30fps speed on the LAN/WAN by using MJPEG hardware compression technology.
IPCAM User Manual IPCAM supports Multi-Protocol such as TCP/IP, SMTP and HTTP. Sending the image to your mailbox automatically when the IPCAM is triggered. Motion Detection Your may use the internal Motion Detection function or external sensor to trigger images recording and transportation. DDNS support Using the IPCAM in the condition which including ADSL and IP change often is more convenient, because IPCAM provides dynamic DNS function.
IPCAM User Manual 1.3 Product views 1.3.1 Front View IPCAM01 IPCAM02 Figure 1.1 Infrared LED 18 IR LEDs(model 01) /24 IR LEDs(model 02) LENS CMOS sensor with fixed focus lens. Wi-FI Antenna Wireless Antenna 1.3.2 Interface LAN : RJ-45/10-100 Base T DC5V : 5V/2A Power supply RESET BUTTON: Press and hold down the RESET BUTTON for 5 seconds.Release the power button and IP camera will be reset back to the factory default parameter. 1.
IPCAM User Manual CAUTION: Make sure to only use the power adapter supplied with IPCAM. Using a non-approved power adapter may damage the camera. 3) The camera takes approximately 30 seconds to start up before it displays an IP 4) address on the IP Camera Tool(details: 2.1). When the camera is powered and network cable plug correctly.It’s head will turn around and the Network Indicator LED is blank. 1.6 Software installation Software installation is the key to the successful use of this product.
IPCAM User Manual Figure 1.6 The computer restarts upon installation completion and an icon appears on the desktop automatically. NOTE: Before installing and using the product, please read the following precautions carefully and make sure they are fully understood. Use only the power adapter attached with the product. Use of unauthorized power adapter may cause damage to your IP Camera. IP Camera terminal shall be installed in an indoor environment.
IPCAM User Manual 2 SOFTWARE OPERATION 2.1 IP Camera Tool When the Device has been mounted properly, you can double click the icon “IP Camera Tool” and a dialog box as Figure 2.1 will pop up. Figure 2.1 Note: The software searches IP Servers automatically over LAN. There are 3 cases: 1 No IP Camera found within LAN. After about 1 minute search, the Result Field will show “not found IP Server” and the program shut automatically; 2 IP Cameras having been installed within LAN.
IPCAM User Manual Figure 2.2 Basic Properties There are some device information in the Basic Properties, such as Device ID, System Firmware Version, Web UI Version. Figure 2.3 Network Configuration In this page, you can configure the Network parameter. Figure 2.4 DHCP checkbox:if checked, the device will obtain IP from DHCP server (To be make sure the Router which the device connect with has DHCP function).
IPCAM User Manual Figure 2.5 Refresh Camera List Refresh camera list manually. Flush Arp Buffer When cable network and wireless network of the device both are fixed IP address. There is a a problem you may encounter is can search the camera IP but can’t open the camera web page.you may try to use flush arp buffer. About IP Camera Tool There are some Basic informations of IP Camera Tool, such as IP Camera Tool Version, IP Camera ActiveX control Version.
IPCAM User Manual 2.2 Camera Login You can access the camera through IP Camera Tool or IE directly. 1) Double click the IP address of the IP Camera listed(Figure 2.1).IE will be opened automatically and display the camera login page. 2) Access the camera by IE browser directly, type in the camera’s IP address.for example: 3) The Camera Login page pop-up. Figure 2.6 enter your account and password on the login page as shown in Figure 2.6. By default， administrator’s username is:admin and no password..
IPCAM User Manual 2.3 For Visitor Figure 2.7 For example: if is bright ,the first route is on Detection(Motion Detection). If you want to detect 4 views , need to click this ico .The first you should add more deivce.see details in 2.5.1 Multi-Device Settings. OSD: Display date and time on the video. You can disable the OSD function or choice other color.
IPCAM User Manual received in mailbox is like this: device id(Alias)_ Current time.jpg For example: 00606E576A02(IPCAM)_m20081216212745.jpg It means the device ID is 00606E576A02, the device alias is IPCAM and its picture’s time is : At 21:27:45 on December 16, 2008 2.4 For operator When login as operator or administrator, you can enter the For Operator. Figure 2.8 Flip: To see the flip image. Mirror: To see the mirror image.
IPCAM User Manual 2.5 For Administrator When you login as administrator, “For Administrator” is enabled. Device Info:You can find the information about Device ID,Firmware Version and Embeded Web UI Version. Alias Settings: You can Input the new name as you like. Data&Time Settings: Data&Time Settings page. Users Settings: Eight accounts are acceptable for this system. Here the eight users can configure their user names and password as Administrator, Operator or Visitor. Figure 2.
IPCAM User Manual sofeware in this page. Restore Factory Settings: Restore factory settings of the device. Reboot Device:Reboot the device. log: Record who entered ipcam Back: Back to Monitoring Mode. 2.5.1 Multi-Device Settings Add cameras in LAN In the Multi-Device Settings page,you can see all devices searched in LAN.The 1st Device is this device deault.You can add more cameras list in LAN for monitoring. This Web software supports up to 9 IP Cameras online simultaneously.
IPCAM User Manual Figure 2.11 Figure 2.
IPCAM User Manual 2.5.2 Network Settings Basic Network Settings If the router that the IP camera connect has DHCP function, you can choice “Obain IP from DHCP Server” else fill in the network parameters manually. Http Port:In most cases, you can leave this value as 80, however, if your Internet Service Provider blocks this port, you may switch to another port number such as 8005. Figure 2.
IPCAM User Manual Figure 2.14a 2) Automatic Please Click the button ‘scan’, Wireless Network showed in the Wireless Network list. Then Select a wireless network.. writed the correct password. ADSL Settings When connected to the Internet through ADSL directly, you can enter the ADSL username and password obtained from ISP. Figure 2.15 2.5.3 DDNS Service Settings DDNS Service: The system supports protocols from some DDNS providers: Dyndns.org.
IPCAM User Manual DDNS or Proxy Server:If you access the DDNS host through a proxy, you should input the Proxy IP. DDNS or Proxy Port: Proxy Port Figure 2.16 2.5.4 Mail and FTP Service Note: When Alarm Service Settings－> Send Mail on Alarm is check, the Mail Service takes effect. Configure the E-mail box to receive and send mails. The E-mail box is used for receiving the images sent after alarm and the system IP address after successful dial-up. Sender: This device use the sender mailbox to send mails.
IPCAM User Manual internet IP by mail.(for example:IPCAM 's url is http://119.123.207.96:9002). Make sure the port is map to the router correctly by UPNP or Virtual Map function. Figure 2.17 Settings the FTP Service. Note:When Alarm Service Settings－> Upload Image on Alarm is check, the FTP Service takes effect. FTP Server: the FTP server address. FTP port: the port usually is 21 FTP Mode: support standard(POST) mode and passive(PASV) mode.
IPCAM User Manual Figure 2.18 2.5.5 Motion Detection Enter Alarm Service Settings page to configure Motion Detection function. Motion Detect Armed When you enable motion detect armed, the camera can be triggered to send email alerts and record images.In the caemra monitoring page,the green ico turn to red and an alert sound you will hear, Motion Detect Sensibility you can choose a level from 1 to 10. the most sensitive is 10.
IPCAM User Manual Figure 2.19 2.5.
IPCAM User Manual 3 HOW TO USE 3.1 Step by step to use Follow the instructions below to get started after the Camera has been mounted properly. When the IP camera powered on,it will rotate itself and stop to the center. 1) Use Network cable connect IP Camera to LAN. 2) Enter IP Camera Tool to set the basic configuration.(details: 2.1) 3) When IP address of the Camera listed in the Result Field of the IP Camera Tool, it means the basic configuration is completed.
IPCAM User Manual 4) Wait at least 30 seconds to unplug the ethernet cable, then unplug the power supply. 5) Plug the power supply making sure that the ethernet is not connected 6) After around 30 seconds, if the LED blinks ,it indicates it is working in wifi mode 7) Camera login.(details:2.2) 3.3 Connected to the Internet through ADSL directly Figure 3.2 1) Use Network cable connect IP Camera to PC 2) Enter IP Camera Tool to set the basic configuration.(details: 2.
IPCAM User Manual Figure 3.3 1) Use Network cable connect IP Camera to the LAN. 2) Enter IP Camera Tool to set the basic configuration.(details: 2.1 ) 3) login the Camera homepage as Administration. 4) Enter DDNS Settings Page and ennable DDNS service .Click and the device will reboot. (details: 2.5.3) 5) You can access the Camera from Internet by domain name. 3.5 Static IP user Static IP user is not need to use DDNS for remote access.
IPCAM User Manual function.Enter ipcamera “Upnp Settings” to enable UPNP and make sure the state is “Upnp success”. If your router has the Virtual Map function.Enter router setting page,add ipcamera’s IP and port to the Virtual map list. 3.6 How to use DDNS When use ADSL, the IP Camera will connect to the Internet through ADSL automatically. For each ADSL reconnection,ISP will re-assign a new IP address for the IP Camera to facilitate the access.
IPCAM User Manual Figure 3.5 3.7 How to use mobile telephone to enter ipcam 1) Copying the IPCamera.jar from CD to the device memory. Follow the prompts to install the IPCamera.jar. 2) Running ip camera player. 3) Filling in alias, hostname or ip, port, user, password, resolution. Then Clicking the OK button.
IPCAM User Manual 2、Only support midp2.
IPCAM User Manual 4 APPENDIX 4.1 Frequently Asked Questions Note: Any quesetions you would meet,please check Network connections firstly. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 4.1.1 I have forgotten the administrator username and/or password. To reset the administrator username and password, Press and hold down the RESET BUTTON for 5 seconds.
IPCAM User Manual 2）download ActiveX controller and set the safety property of IE in the PC when you view it first time: “IE” browser“Tool”“Internet Proper”“Security”“Custom Level””ActiveX control and Plug-ins” three options of front should be set to be “Enable”, The ActiveX programs read by the computer will be stored.as follows: Enable:Download unsigned ActiveX controls Enable:Initialize and script ActiveX controls not marked as safe Enable:Run ActiveX controls and plu-ins Figure 4.1 4.1.
IPCAM User Manual Figure 4.2 Step2: enter your information Figure 4.3 Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/account/confirm/vXMVT78-KvehydmKMWH5kg) Step4: When the Account Confirmed, login and start using your account. Choose Add Host Services(Figure 4.4) and enter Add New Hostname (Figure 4.5)page.
IPCAM User Manual Figure 4.4 Figure 4.5 Step5: On the Add New Hostname page. 1) input your Hostname. 2) choose Host with IP address 3) click Use auto detected IP address xxx.xx.xx.xxx. Then click Create Host. Figure 4.6 Step6: Now you obtained a Dynamic Domain Name(Figure 4.6),and can use it in the DDNS Service Settings(details: 2.5.
IPCAM User Manual 4.1.7 Why pop-up the prompt”Fail to connect to the device…”? This prompt only appeared in the case of using multiple cameras. Enter the Multi-Device Settings page(login as administrator) to check the Device setting is correct or not. When one of the multiple cameras disconnected, the color changed to yellow and pop-up the prompt “Fail to connect to the device…”. Figure 4.2 4.1.
IPCAM User Manual but its office provides a plug-in named IE-Tabe for us and which can enable firefox to support ActiveX controls, you can access the website as follows with the firefox explorer: https://addons.mozilla.org/en-US/firefox/addon/1419 On the download page, select the right version for your browser, download it, then start the installation. Now, we take the firefox browser whose version is 2.0.0.18 as the example to describe the whole procedure.
IPCAM User Manual 5 In the end click “Restart Firefox” button to restart the browser. 6 Login your device and locate the monitoring page, click your mouse’s right button, click the new menu item named View page in IE-Tab to login device again.
IPCAM User Manual 4.2 Default Parameters Default network Parameters IP address: dynamic obtain Subnet mask:255.255.255.
IPCAM User Manual 4.3 Specification ITEMS Image Sensor Lens Video Communication Physical Power IPCAM01/02 Image Sensor 1/4" Color CMOS Sensor Display Resolution 640 x 480 Pixels(300k Pixels) Lens f: 6mm F:1.8 (IR Lens) Mini. Illumination 0.
IPCAM User Manual 5 OBTAINING TECHNICAL SUPPORT While we hope your experience with the IPCAM network camera is enjoyable and easy to use, you may experience some issues or have some questions that this User’s Guide has not answered. To obtain the latest information and support for your Observer network camera, please visit our webpage for additional FAQ’s and troubleshooting tips.
