! ! ! ! ! ! ! ! Wireless/Wired Network IP Camera ! (For PC View) Night Vision & Remote Operation ! ! User Manual ! ! ! ! ! ! ! ! ! ! ! ! ! ! !1
! ! Thank you for buying our IP camera ! ! ! Wanscam JW Series IP Camera products are designed and equipped for local and !remote network video surveillance system, including wired IP bullet camera, wireless IP !bullet camera, IP IR dome camera, IP IR waterproof camera, IP Pan/Tilt/Zoom Camera etc. !We adopt high performance chip to ensure high quality media processor which processes !audio and video collection, compression and transmission.
! Table of CONTENTS ! 1. Product Introduction ...........................................................................................3 1.1. Safety Introduction .........................................................................................3 1.2. Product Specifications................................................................................. ....3 1.3. System Requirements........................................................................................3 1.4. Product Views……………..
! ! ! ! ! ! ! 1. Product Introduction ! 1.1 Safety Instructions ! (1). Use the proper power source. Do not use this product with a power source that supplies more than the specified Voltage (100-240V AC). ! (2). Never insert anything metallic into the camera. Inserting metal object into the camera can be a source of dangerous electric shock. ! (3). Do not operate in wet or dusty environment. Avoid places like a damp basement or dusty hallway. ! (4). Do not attempt to disassemble the camera.
*- Adopt high Performance, strong function media processor 32Bit RSIC *- High sensor CMOS *-Adopt optimized MJPEG video compression algorithm, realize high-definition images transmission in narrow bandwidth; *-Maximum support 15 users viewing at the same time, no limit for users if using forwarder Server function; *- Built in Web Server, convenient for users to use standard browse to realize the real time monitoring and setting administration; *-Support WIFI:802.
! ! ! ! 1.4. Product Views ! ! 1.4.1 Front View 1.4.2 Interface View ! ! ! Figure 1.1 Figure 1.2 !1: Audio Out , 2: Audio In 3: Ethernet interface: RJ-45 interface. Power Supply Light: constant on after power up Network light: constant sparkle after power up data transmission. 4: Antenna: 5: Power input interface: connect direct current 5V Power 6: TF Socket : No use for model :JW0004. Only use for model : JW0005. !! 1.5 Hardware Installation !Follow the steps below to set up your camera hardware.
! ! ! ! 1.6 ! ! Figure 1.3 Software Installation ! ! Figure 1.4 ! Open the CD Install the follow software: ! 1. ActiveX: Click “OCX setup”—“Next”—“Install”—“Finish”. 2. Search Tool: Open the CD, click" ,The Search Tool will run automatically.( No need to install. You can copy this software to your desktop.) ! Figure 1.5 ! ! ! 2. Software operation ! 2.1.
! 2.1.1. Search the IP address of the camera. When the device has been mounted properly, you can double click the Icon “" run this IP address search tool. ” ! Figure 2.1 !Note: The software searches IP Servers automatically over LAN. There are 2 cases: 1. No IP Cameras found within LAN. After about 1 minute search, the Equipments List Field not show the IP address. 2. IP Cameras have been installed within LAN.
2.1.2 Configuration of the Network Once your camera’s IP address’ Subnet Mask, Gateway, DNS Server is the same as your PC or router, you need configure the camera’s Network parameter manually. IP address: Fill in the IP address assigned and make sure it is in the same subnet as the Gateway, and the subnet should be the same as your computer or router. (i.e. the first three sections are the same) Subnet Mask: The default subnet mask of the equipment is: 255.255.255.0.
Password: no password. Input the correct user name and password, the Sign In interface will pop-up. There are three models to login (figure 3.2). ! Figure 3.2 !(1) ActiveX Mode (For IE Browser): available in IE6.0 or above explorer (2) “RTSP Stream Mode”: available in Firefox, Safari, and Google browser. (3) “No Plug-In Mode”: available in smart phone browser. (4) SD card video playback online ! ! 2. View via IE Browser. ! ! Choose Active Mode (For IE Browser), and sign in.
! Figure 3.3 After Download Ocx-Setup (oPlayer Software), Click and install it, untill finished. ! Figure 3.
! Figure 3.3 Windows XP system ! Figure 3.4 Win7 System !Note: If there is still no live video after run ActiveX, please try to enable the ActiveX options of IE security settings, please do the follow steps: 1. Close the firewall of your computer. 2.
! ! Figure 3.5 ! Figure 3.6 In Addition: you can also click “start” menu->“Internet Explorer”, choose “Internet attributes “ to enter, or via “Control Panel” ->“Internet Explorer”, enter to Security setting. 3. If there is still no image, please close your anti-virus software, and then try step 1 & 2 again. 4.
! Figure 3.7 NOTE: Make sure that the firewall or anti-virus software doesn’t block the software or ActiveX. If you couldn’t see live video, please close your firewall or anti-virus software, and try again. ! 3. View via Safari, Firefox, Google Browser !Choose Server Push Mode (For Safari, Firefox, Google Browser), and sign in Server Push Mode doesn’t support ActiveX, so some functions are not available, such As Record, Audio, Talk, Speaker,The speed control bar, Zoom etc.
! 4. Main Menu interface introduction ! Take the “Active Mode(For IE Browser)” For example: ! ! Figure 3.
! The Pan/Tilt Feature only work when the cameras have this Pan/Tilt function. ! " This option enables log detection. After the online user clicks this button, a log is entered into the camera’s Log Data documenting the IP address of users who have accessed the IP camera. This Option enables alarm detections too. ! " This button make the camera Vertical cruise (for the Pan/Tilt Cams). " This button make the camera Level cruise (for the Pan/Tilt Cams). " This button flips the image vertically.
5. Administer Setting Instruction !When login as Administrator, you can enter the IP Camera for Administrator. Administrator supports all the settings and operations of the camera; you can set and control it freely There are some special functions only for administrator as below: !Alias setting : You can set your favorite device aliases. Date&Time set : seting the date and time. Uer settings : Can be set up to 8 users.
! Figure 3.10 3.5.2 Network Settings ! ! Figure 3.11 This sector is for DHCP and IP configuration, port forwarding is needed, If you choose to set IP address,please fill in the relative IP address, subnet mask, gateway, DNS server, Http port; 3.5.
1. Make sure the router is a wireless router. 2. Make sure the Wi-Fi antenna installed. 3. Make sure whether there is encryption of the WLAN of the router, if there is encryption, keep the key. 4. Login the camera, click " >“Wireless Lan Settings”>”Scan”, please scan 2times, then you will find the WLAN from the list, choose the one you use. 5. If there is no encryption, just click “Submit”, if there is encryption, please input the key, then click “Submit”. 6.
! Figure 3.13 ! (2): Choose the DDNS, there are 4 kinds of options: !(1): Manufacturer’ DDNS: We provide a free DDNS: vipcam.org. This domain is provided by manufacturer. !Note: 88safe.com is old DDNS provided by manufacturer also. If you want use the manufacturer’s free DDNS, Please Choose to use vipcam.org. ! ! 3.14 !(2): The Third Party DDNS: This domain isFigure provided by the 3rd party, such as Dyndns, Oray, 3322 If you use the third party DDNS, please choose the server you need, such as “3322.
! Figure 3.15 Figure 3.16 You have to register an account firstly, keep the user, password, host, then fill in it. Note: Only one DDNS can be chosen, for example, if you use manufacturer’s DDNS, the 3rd party one won’t work, if use the 3rd party DDNS, the manufacturer’s one won’t work. ! 3.5.4.2 Port forwarding settings: 1: Setting the IP address of the camera !The default IP address of the camera is : Http://192.168.1.
! Figure 3.17 Make sure the “Subnet Mask”, “Gateway”, “DNS Server” is the same as your router. !! 2: Setting Port Forwarding in the router. !This is the most important step. Set port forwarding in router refer to the IP of your camera correctly, then the DDNS will work.
Fill the service port (except 80), IP address of the camera, then click Save The port and IP address should be the same as Camera. ! BELKIN: (1) Login the router. (2) Choose “Firewall”, select “Virtual Servers” (3) Input the port (except 80) and IP address, then click save. Note: The port and IP address should be the same as Camera. Figure 3.18 DLINK: (1) Login the router.
(3) Input the port, IP address, Protocol, then click save. Note: The “public port” & “private port” should be the same as camera’s port, choose the protocol to be “both”. Figure 3.29 After all these 4 steps done, then you can use the DDNS freely, check the DDNS status from the camera as below, and get the link of DDNS for internet view. Step: “Login”>” " ! ”>”Device Info”: Figure 3.20 3.5.5.
!For example, you can go to Dyndns website to register a free account. http://www.dyndns.org / http://www.dyndns.com. !Step1: enter http://www.dyndns.com/ and Create Account ! ! Figure 3.21 !! Step2: Set the username and password as below: ! Figure 3.
Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/confirm/create/ONMzltcCBk6mcHJI5MhVD0g) ! ! Figure 3.23 ! ! Figure 3.24 Step4: When the Account Confirmed, login and start using your account. Choose Add Host Services(Figure 3.25) and enter Add New Hostname (Figure 3.26)page. ! ! Figure 3.
! ! Figure 3.26 Step5: On the Add New Hostname page. 1) input your Hostname. 2) choose Host with IP address 3) click Use auto detected IP address xxx.xx.xx.xxx. Then click Create Host. 4) after you have added a New Hostname , you need “Proceed to checkout” ! Figure 3.
! Figure 3.28 ! ! Figure 3.29 ! Step6: Now you obtained a Dynamic Domain Name(Figure3.30),and can use it in the DDNS Service Settings(details: 3.5.5) ! Notice: If you have a dynamic IP address, Make sure you have download the DynDNS’s “Update Client”. And installed it succeed in your computer. ! !! ! !! ! Figure 3.
3.5.6 E-mail and FTP service Settings ! ! Figure 3.31 The above setting is a preparation for the alarm function, the sender should be entered the sender’s email address，recipient 1、2、3、4 is filled with recipient E-mail address；SMTP server should be filled with the sender email SMTP server，e.g. the sender email address is abc@163.com，and enter mail.163.com.
triggered it also sends image,please enter FTP server,FTP port,FTP user,FTP password, FTP upload directory,FTP mode,FTP mode has two options: PORT and POSV. If needs a quick upload image, then select it, edit upload image interval（second） !! 3.5.7.
3.5.8 Record&Capture Path This sector is for Record&Capture Path in your computer.It include: Record&Capture Path, Record file length(MB), Record time length(Minute), Reserved disk space(MB), Record cover. ! ! Figure 3.34 3.5.9 Reset/Firm Ware Upgrade ! This sector is for camera firmware upgrade, it includes device system firmware " and device application firmware " Be cautious to apply for it! ! Figure 3.35 ! !31 .
3.5.9.1 Restore Factory Settings ! When users forget password, we can restore ex-factory settings, when click, a picture will pop up, Click ok, and wait for 1 minute and you can use it normally. User setting feature restores ! ! ! Figure 3.35 3.5.9.2 Reboot Equipment ! Click restart, it appears the above picture, click ok, wait for 1 minute and you can use it normally ! ! !! !! !! !! !! !! !! ! ! Figure 3.
! 4. Warranty Under normal use condition, products resulting from its own failures in the warranty period will be free maintenance. Warranty Terms as following: a) Charge-free maintenance of the product is one year. We can repair it for free during the guarantee period (Damages not caused by misuse or vandalism). Repair over guarantee period, we will charge maintenance fee. b) During guarantee period, breakdown caused by misuse or other reasons out of range of warranty.
