B Series——Waterproof Model NCB-543W User Manual V4.
http://www.wansview.com Index 1 2 3 INTRODUCTION ...........................................................................................................................4 1.1 THE PACKAGE INCLUDES ..........................................................................................................4 1.2 FUNCTION AND FEATURES ........................................................................................................4 1.3 TECHNICAL PARAMETERS .......................................
http://www.wansview.com 5.4.2 Time Setting .......................................................................................................................20 5.4.3 Firmware upgrade .............................................................................................................20 5.4.4 Restore Factory Default.....................................................................................................20 5.4.5 User browsing Log........................................................
http://www.wansview.com 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet. 1.1 The package includes 9 IP Camera * 1 9 IP Camera Utility CD *1 9 5V Power Adapter *1 9 Stand of plastic * 1 9 Cable * 1 NOTE:If you select the device with wifi function, it has built-in wifi module and transmitting antenna in package. 1.
http://www.wansview.com 1.3 Technical Parameters Item Image Capture Assistant Video and Audio Network Other Features Physical Index Software(PC Side) Sub Item Description Sensor CMOS sensor Total of pixel 300k Minimum illumination IR on,0 Lux Lens f=4.0mm, F=2.
http://www.wansview.com 2 Appearance and interface 2.1 Appearance Figure 1 2.2 Interface of Equipment Figure 2 3 Visit IP Camera from LAN 3.
http://www.wansview.com 3.2 Search and set the ip address of the ip camera Run “BSearch_en.exe” in the CD, the setting interface as figure 4. Figure 4 Operation Steps: 1) Click “Search (F3) 2) Choose the device 3) Change the ip address of the ip camera according to the information in the red frame on the left. The numbers in the red circle should not be the same. 4) Put the user name and password into “Authentication” (By default, the user name is: admin, password is: 123456).
http://www.wansview.com Figure 5 3.3 Visit IP Camera We suggest using IE kernel browser to view the video (it can provide more functions), but user need to install Player before viewing the video. Click “download and install player (first use)” link, it will popup dialogue box as Figure 6, click Run, it will automatically download player and install. Figure 6 3.3.1 Video Play Area After install the plug-ins, click “Mode 1 to view” link in Figure 5 to view the video (video as Figure 7).
http://www.wansview.com Figure 7 1) Main Menu The main menu includes the function setting of different submenu 2) Status Displaying Area In right up corner, it is the status displaying area, to show the 9 devices’ status: if not connected, button is gray if connected, button is green If wrong connected , button is yellow If alarm , button is red 3) Multi Channel displaying area If users add multi channel(refer to 5.3.2), when shift to 4-Ch, 9-CH, and it will automatically show other devices.
http://www.wansview.com Figure 8 4) PT and video control In Pan/Tilt control area, user can control the position according to the arrow sign: up, down, left, right, middle, horizontal cruise, vertical cruise, and stop etc. Means open IO output and Close IO output. User can also set the device frame rate、resolution, brightness, contrast and other parameters. Note : For this model , no Pan/Tilt ,Alarm I/O function , but you can control other camera when use multi-view . 4 Visit IP Camera from WAN 4.
http://www.wansview.com Figure 10 Operation Steps: 1) After login the interface of the router,choose “Port Forwarding” 2) Choose “Add custom Service” 3) Input IP camera port 4) Input IP camera IP address,click “Apply”。(the http port and ip address should be the same as figure 4 which set by you own) Note: Different router has different settings for port-forwarding; please kindly follow your router guide to do the port-forwarding. After the port-forwarding is done, you could view the IP Camera from WAN now.
http://www.wansview.com 4.3.2 Third Party DDNS User can also use third part DDNS, such as www.dyndns.com User must apply a free domain name from this website and fill the info into the below blanks (Figure 12) and save the settings. Then the domain name can be used. Figure 12 Note: Using the third party domain name, if the http port is not 80, the port number should be adding to the domain name with colon. Example: http://btest.dyndns.biz:81. While manufacturer DDNS is no need to add PORT.
http://www.wansview.com Figure 14 Note1: When the device is connected both WIFI and wired, it will firstly connect to the wired network, if it can’t connect to it, then it will change to connect to the wifi. The IP address and port is the same, either wireless or wired network. Note2: Before you do the configuration of wireless as shown above; please make sure the device is connected to the network via network cable. After settings succeed, please reboot the device and wireless function takes effect. 5.1.
http://www.wansview.com with the equipment, if not, we would suggest you to disable this function and do the port-forwarding manually. 5.1.5 DDNS Setting Please refer to the content in 4.3. 5.1.6 MSN Setting Figure 17 User needs to apply for a MSN account for this device first, for example: test1@hotmail.com. Please put this MSN account and its password as above Figure 17. Then put your MSN account, for example: friend1@hotmail.com, into the ‘MSN Friends List. Then on your friend1@hotmail.
http://www.wansview.com Figure 18 2) Alarm Action All kinds of alarm modes:a) IO interface for alarm signal output: when relay is switched on, the external alarm will begin to alarm. b) Send alarm info by email. c) Send the site pictures to the FTP server, user can also set the break time between two pictures. d) Send alarm info to the alarm server. 3) Scheduler Device will trigger alarm in scheduled time. User can set schedule time to be “all the time”.
http://www.wansview.com Figure 19 5.2.
http://www.wansview.com The device will send alarm email to you. You only need to fill out the blanks with your email address as shown in Figure 20. After the setting, please click save and test to check if it works properly. If it is properly set, user can tick to enable “Report Internet IP by mail”. After every restart, the device will send its Internet IP address to user’s email address. 5.2.
http://www.wansview.com userpwd=password& rea=alarm type (1=Motion Detection, 2 =Alarm from Alarm in port)& io=0 Alarm server needs developing by user. User can extend other functions on this server, like SMS, MMS alarm, and mobile phone etc. 5.3 Advanced 5.3.1 User Setting There are three levels of authority; they are Administrator/Operator/Visitor. Administrator have the highest authority, it can do any change to the settings.
http://www.wansview.com Figure 24 As Figure 24, User can maximum add 9 devices to view the device simultaneously. Click refresh button to check the device in the LAN. When click the device, will popup setting dialogue box and input the device info, as figure 25 and click save. After that, must click submit button to save. Figure 25 5.3.3 Other settings Figure 26 Note: the settings for the status light and pan/tilt are not suitable for this item 5.4 Maintain 5.4.
http://www.wansview.com 5.4.2 Time Setting If the device is connected to the Internet, you enable the NTP server to correct the time and select the right time zone. Or you should use the PC’s time to correct its time. Figure 28 5.4.3 Firmware upgrade The device runs 2 kinds of programmer, one is system firmware, the other is application firmware. They could be upgraded separately. Figure 29 5.4.
http://www.wansview.com 6 Centralization Control Figure 31 IPCMonitor is a free software offered by factory, several devices on LAN and WAN can be browsed at the same time. The software also supports snap, video record, alarm and so on. The below Figure 31 is the interface. For more information, pls. refer to the <> in CD.
http://www.wansview.com 4) Can’t find equipment via search software after connect to LAN Make sure the equipment and PC is in the same LAN; if install firewall software, please close it and try again. 5) Can find equipment via search software, but can’t visit If the IP address of IP camera and PC is not in the same Network Segment, you should change them on the same Network Segment before visit. Network Segment is the first three number of IP address. If the IP address of PC is 192.168.0.