Dear users, the configuration for this camera is professional, so please read the user manual carefully before using the camera. 用户手册。 IP CAMERA （H series） User manual 2012-12 V1.
http://www.wansview.com Statement If the user manual can not help you to solve the problem, please call our technology center about the solutions. We will update the content for the new functions without notice. Notice 1、 Installation Environment Keep away from the places for high-temperature, heat source and direct sunlight； Keep away from water and when get wet, cut off the power immediately.
http://www.wansview.com Index 1. 2. 3. PRODUCT INTRODUCTION ................................................................................................................................. 5 1.1. PRODUCT SUMMARY ........................................................................................................................................... 5 1.2. PACKAGE FOR TYPICAL PRODUCTION ..................................................................................................................
http://www.wansview.com 5. PRODUCT FAMILY FOR NCH SERIES............................................................................................................ 24 5.1. NCH530W INDOOR VGA PTZ CAMERA .......................................................................................................... 24 5.2. INDOOR HD PTZ CAMERA ................................................................................................................................ 24 5.3. HD WATERPROOF CAMERA ..........
http://www.wansview.com 1. Product introduction 1.1. Product summary Thank you for choosing our company‟s H series IP camera, which has several models, including indoor VGA PTZ camera, indoor HD PTZ camera, HD waterproof camera etc. It is very suitable for family, shops, office building and so on. Main features for H series： Support 2 kinds of H.
http://www.wansview.com 5V √ √ √ √ 12V √ √ √ √ 12V √ √ √ √ 12V √ √ √ √ NCH537MW Indoor HD PTZ camera NCH532MJW HD waterproof camera （simple model） NCH532MW HD waterproof camera (full function model) NCH531MW HD box camera Notice: If you choose IP camera with wireless function, so it includes wifi module inside the camera and antenna in package. Please check carefully if all listed items are included in the package, if anything missing, please contact vendor in time. 2.
http://www.wansview.com Figure 1 Insert CD to computer driver, double click “HSearch_en.exe” in the CD, will pop up the interface as figure 2, please operate as the following steps: 1) Figure 2 Click „Search‟（Please make sure your firewall will not block up the item to be searched） 2) Choose a camera; 3) Change the ip address of the ip camera according to the information in the red frame on the left. The numbers in the red circle should not be the same.
http://www.wansview.com (F4)”. Then you can run the web browser , enter user name and password and login IP camera to view the video, example of figure 3.（please use IE browser at first time） Figure 3 Notice: Need to download ActiveX when first use, click “download ActiveX( when first use)” in figure 3, will display prompt as figure 4, click „run‟ will download and install the ActiveX automatically.
http://www.wansview.com Figure 5 Select „On‟ and click „Search‟, and then select wireless router in pop up menu, click „OK‟ and enter its password, click „apply‟ to save the wireless settings. And you can click „check‟ to check if the wireless setting is successful. After setting successfully, please pull out network cable and restart the camera to use the wireless function. 2.3. Operation step for connecting to WAN You should connect it to LAN network and do port forwarding at first, connect as figure 6.
http://www.wansview.com 1) 2) 3) 4) Figure 7 Please go to the setting interface of Router, and choose “Port Forwarding”； Choose “Add custom Service” ; Input IP camera http port; Input LAN IP Address of the camera, click “Apply” (port number and IP address as you set in figure 2） After finishing the port forwarding, you can use WAN IP address of router and http port of camera to visit the camera by remote computer as figure 6.
http://www.wansview.com 3. Operation of using IE browser 3.1. View video Figure 8 1) Status bar Figure 9 ① Display connection status; ② Display record status: if click “Record”, it will show “REC” which stands for recording; click record button again, it will stop; ③ Zoom out, zoom in and restore digital zoom; ④ Set the file saving location: you may set the location for recording and captured picture; ⑤ Talk-back button: it can transmit the sound which collected by the computer to the equipment.
http://www.wansview.com If the camera supports PTZ function, you can click up, down, left, right arrow to control the camera moving, click button to center and stop the camera. when you set camera to a position, and then click „SET‟，after the camera was changed the direction, click „CALL‟ can move the camera to the position you have set. Notice：Because H series have many models, the waterproof models need to be connected with external PTZ, and need to set PTZ parameters (please refer to chapter 3.5.
http://www.wansview.com 3.2.2. Audio parameters Figure 11 Audio input can select MIC or line in. The camera supports G.711 and G.726 audio encoding format. The sound of the G.711 is better, but it occupies more bandwidth. If you click “On” of the audio capture, so it will transmit audio in corresponding video stream. You must open the audio here, otherwise you can‟t hear the audio when clicking audio play button in figure 9. 3.2.3.
http://www.wansview.com 3.3. Web setting 3.3.1. Basic web setting Figure 13 3.3.2. WiFi setting Please refer to chapter 2.2. 3.3.3. WAN access setting In chapter 2.3, you have known how to do port forwarding. After doing port forwarding successfully, you can also visit camera by DDNS. The manufacturer has established a DDNS system, and allotted a DDNS to every device, the user can view it from remote PC, example of figure 14. Figure 14 User can also use third party DDNS, such as www.dyndns.com.
http://www.wansview.com to the domain name with colon. Example: http://mydomain.dyndns.org:81. 3.4. Alarm setting 3.4.1. External Alarm Input Figure 16 The camera should have external alarm input port for enable this functions. Connect external alarm detector to the input port, the detector will output switching signal when it detects any abnormal, input port of the camera will detect the level change, so it will detect the alarm, therefore the detector should be switching sensor (same as switch) 3.4.2.
http://www.wansview.com ways, for example, store in SD/TF, or upload to FTP, or email you, etc. example of figure 18. Figure 18 Note: Please insert the SD/TF Card and tick the “Save Video on the SD card” , “Save video on the FTP server” will take effect. 3.4.4. Alarm time setting Figure 19 The device will trigger the alarm only during the scheduled time period, you can select the scheduled time according to your request.
http://www.wansview.com 3.5. Advance setting 3.5.1. User management Figure 20 There are 3 levels of user authorization in it. Administrator: “admin” has the highest authority. It can do any settings. Factory default password: 123456. User: user can only operate the device but can‟t do any setting changes. The default password is user. Guest: User can view the video, but can‟t operate the device. The default password is guest.
http://www.wansview.com 3.5.3. E-mail Setting Figure 22 In Figure 22, the blanks which have been filled with info should be filled. If any info is not filled right, the setting will fail. Notice: the password should not use special character; otherwise the camera can‟t identify it. 3.5.4. FTP setting Figure 23 In order to use FTP function, user should apply user name and password on the FTP server at first.
http://www.wansview.com 3.5.5. Alarm server Setting Figure 24 Alarm server need to develop by user; user can extend other functions on this server, like SMS, MMS alarm etc. If you have built alarm server, and set your alarm server info like Figure 24. The camera will send alarm message to alarm server, the format as follow: GET /api/alarm.
http://www.wansview.com 3.6. System setting 3.6.1. Device information Figure 26 Network Connection status will display “LAN” when connected by wired cable and display “Wireless LAN” connected by WIFI. SD/TF status will be displayed if SD/TF card inserted and display the free capacity. Notice: the device supports max 32G SD/TF card. Please format the SD/TF card to FAT32 before use the card on camera. Please check if the SD/TF Card matches the camera or not before purchase the SD/TF Card. 3.6.2.
http://www.wansview.com Example of figure 27, please select the time zone first. There are three options to set the time and date. They are manual setting, sync with computer time, from network time server. 3.6.3. Initialize setting Figure 28 You can upgrade the firmware here. 3.6.4. System Log Figure 29 3.6.5.
http://www.wansview.com 4. Operation of using other software 4.1. Other web browser In the Windows OS, using browser with IE kernel, user must download the ActiveX. Please Download “QuickTime” plug-in and install it before you use Safari, Firefox to access the IP camera. After installation, users can start the QuickTime program, and to access the QuickTime Preferences dialog box from Edit Menu, example for figure 31. Click Advanced, select “custom.” in the Transport Setup.
http://www.wansview.com 4.3. PC Client software IPCMonitor is a free software offered by factory, several devices on LAN and WAN can be browsed at the same time. The software also support real time recording, schedule recording, alarm, snap, and so on. The interface is as Figure 32. Figure 32 For more information, pls. refer the <> in CD. 4.4. Other software As the device supports RTSP protocol, you can use VLC player to play IP Camera video. It is compatible with VLC 1.1.
http://www.wansview.com 5. Product family for NCH series 5.1. NCH530W Indoor VGA PTZ Camera Figure 33 300K pixels CMOS sensor, IR-CUT, 4mm lens，built in PTZ, MIC, support SD card, 8pcs IR LED, audio in/out interface, alarm in/out interface. It uses 5V power adaptor. 5.2.
http://www.wansview.com Figure 35 NCH537MW Above two cameras have the following items: Mega pixels CMOS sensor, IR-CUT, 3.6mm lens， built-in PTZ, MIC, support SD card, 10pcs IR LED, audio and alarm port. It uses 5V power adaptor. NCH536MW camera supports SD card and audio in/out, alarm in/out; NCH537MW camera supports TF card and audio out. 5.3. HD waterproof camera Figure 36 NCH532MJW（simple model） Mega pixels CMOS sensor, IR-CUT, 6mm lens, 36pcs IR LED, It uses 12V power adaptor.
http://www.wansview.com Figure 37 NCH532MW（full function model） Mega pixels CMOS sensor, IR-CUT，8mm lens，36pcs IR LED, audio in/out, alarm in/out. The RS485 port can be connected with external PTZ. You need to open the back cover when you insert SD card. It uses 12V power adaptor. 5.4. NCH531MW HD Box Camera Figure 39 NCH531MW 8mm color lens, audio in/out, alarm in/out, support SD card. The RS485 port can be connected with external PTZ. It uses 12V power adaptor. Statement： 1.
