Professional Food Slicer FS1000/FS1500 For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
IMPORTANT SAFEGUARDS 9. Do not use outdoors. This product is intended for household use only. 10. Do not let cord hang over the edge of a table or counter, come into contact with sharp edges, or touch hot surfaces. 11. Place the appliance on a firm and stable surface. Ensure that the appliance is not placed near the edge of the worktop, where it can be easily pushed off or fall. 12. Never plug in the appliance where water may flood the area. 13.
26. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 18. Do not leave the Waring Pro® Food Slicer unattended while it is running. 19.
IMPORTANT UNPACKING INSTRUCTIONS REPACKING INSTRUCTIONS 1. Put food slicer on a large, sturdy flat surface. 2. Put food slicer into plastic bag. CAUTION: THE SLICING BLADE HAS A VERY SHARP EDGE. To avoid injury when unpacking the unit, please follow these instructions: 3. Position Styrofoam® inserts on each end of the food slicer. 4. Put the packaged unit into the upright box. 5. Replace top corrugated insert, instruction book and other literature. 1. Put the box on a large, sturdy flat surface. 2.
Introduction and even lettuce take no time at all to prepare. ANY WAY YOU SLICE IT! The Waring Pro® Food Slicer eliminates one of the most time-consuming jobs in food preparation. This commercial-quality slicer adjusts from 0 to 24mm to let you slice everything from paper-thin pepperoni to perfect servings of roast beef.
4. 9. 5. PARTS 10. 1. Blade Sharpener (detachable) 8. Carriage Removable Knob 2. Blade Cover 9. Food Guide 3. Cutting Blade 10. 4. Food Arm 11. Main Body 5. Food Carriage 12. ON/OFF Switch 6. Carriage Holder 13. Knob to remove Blade Cover 7. Feet (non skid) 14. Power Cord (not shown) 6. 11. Control Knob Thickness 7. 8. 1. 2. 3. 4. 9. 13. 5. 10. 6. 11. 7. 12. 8.
Operation 10. Continue to slide the food carriage back and forth in an even and steady motion. NOTE: Food carriage is removable for cleaning. See Page 7. 1. To use your Waring Pro Food Slicer, place it on a sturdy, flat surface. ® 11. After all your slicing is done, turn the slicer to the off position and unplug. 2. Check that the switch is in the OFF position before plugging in the appliance. 3. Adjust the thickness control knob to desired slicing thickness (0–24mm). 4.
Food Guide Removal 4. Do not use abrasive substances or solvents. 5. To reassemble, align the bottom of the carriage directly with the carriage holder. Push down and secure into position, insert the carriage removal knob and turn it clockwise until it is securely tightened. 1. Remove the food guide by sliding it off the food arm. 2. Rinse the food guide with water. Slide To Remove Slide To Slide To 6. Any other servicing should be performed by an authorized service representative.
Blade Removal and Cleaning 1. Set the counterplate back to the "0" position. 2. After removing the removable carriage, remove the blade cover by turning the black knob located behind the blade counterclockwise. This piece will come off 3. Clean blade cover in the sink or with a spray cleaner. Knob in back of unit turns counterclockwise 4. When the blade cover is removed, you can clean the blade. 5. Clean the front of the blade with a moist sponge or cloth.
Sliding of Carriage and Food Arm 3. Open the counterplate completely using the thickness control knob while holding the blade sharpener; fit the pins into the holes. 1. The carriage and the food guide slide on rods that are properly lubricated by the manufacturer. Over time the lubrication might dryout, and these parts require very simple maintenance. 4. Do not damage the blade while doing this. 5. Rotate the front part of the blade sharpener until it locks. 2.
13. Using one hand, rotate the front part of the blade sharpener upward, and with the other hand turn the thickness control knob clockwise until the blade sharpener is in front of the blade. Sharpener 14. Plug the cord into the power outlet. 15. Remove your hands and turn the machine to the ON position. 16. Adjust the thickness control knob and turn it slowly until the sharpening stone slightly touches the front of the blade. 17. Maintain a light contact for only 5–6 seconds to remove the burr. 18.
Trademarks or service marks of third parties used herein are the trademarks or service marks of their respective owners. ©2011 Waring Consumer Products 150 Milford Road East Windsor, NJ 08520 www.waringpro.