YF07810-121 DIGITAL CAMERA FINEPIX JZ500/JZ510 Series FINEPIX JZ300/JZ310 Series Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM FinePix JZ500/ JZ510 series, FinePix JZ300/JZ310 series digital camera and the supplied software. Be sure that you have read and understood its contents before using the camera.
Notes and Cautions IMPORTANT SAFETY INSTRUCTIONS • Read Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions: All operating and use instructions should be followed.
Notes and Cautions Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
Notes and Cautions Be sure to read this notes before using WARNING Safety Notes If a problem arises, turn the camera off, remove the battery, disconnect and unplug the AC power adapter. Continued use of the camera when it is emitting smoke, is emitting any unusual odor, or is in any other abnormal state can cause a fire or electric shock. • Contact your FUJIFILM dealer. • Make sure that you use your camera correctly. Read these Safety Notes and your Owner’s Manual carefully before use.
Notes and Cautions WARNING CAUTION Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Do not use chargers other than the specified model to charge the battery. Any of these actions can cause the battery to burst or leak and cause fire or injury as a result. Keep out of the reach of small children. This product could cause injury in the hands of a child.
Notes and Cautions Power Supply and Battery * Confirm your battery type before reading the following descriptions. The following explains proper use of batteries and how to prolong their life. Incorrect use of batteries can cause shorter battery life, as well as leakage, excessive heat, fire or explosion. take care not to place the battery directly against the pad. The camera may not operate if you use a depleted battery in cold conditions.
Notes and Cautions • Do not use batteries that are If any liquid at all leaks from leaking, deformed, discolored. the batteries, wipe the battery • Do not store batteries in warm or compartment thoroughly and humid places. then load new batteries. • Keep the batteries out of reach of If any battery fluid comes babies and small children. into contact with your hands • Make sure that the battery polarity or clothing, flush the area (E and F) is correct. thoroughly with water.
Notes and Cautions • Do not take apart the AC power adapter. Doing so could be dangerous. • Do not use the AC power adapter in a hot and humid place. • Do not subject the AC power adapter to strong shocks. • The AC power adapter may emit a humming. This is normal. • If used near a radio, the AC power adapter may cause static. If this happens, move the camera away from the radio. purely for personal use.
About This Manual Before using the camera, read this Owner’s Manual and the other supplied documents. For information on specific topics, consult the sources below. ✔ Camera Q & A .....................................................pg. ..................................................... pg. x Know what you want to do but don’t know the name for it? Find the answer in “Camera Q & A.” ✔ Table of Contents ............................................ ............................................pg. pg.
Camera Q & A Find items by task.
Camera Q & A Taking Pictures Question How many pictures can I take? Is there a quick and easy way to take snapshots? How can I avoid blurred pictures? How can I make good portraits? Can I choose my own settings for different scenes? Can the camera automatically adjust settings for different scenes? How can I take good pictures of dogs or cats? Can I prioritize to focus the specified person’s face? How do I shoot close-ups? How do I keep the flash from firing? How do I stop my subjects’ eyes glowing red whe
Camera Q & A Viewing Pictures Question How do I view my pictures? How do I delete the current picture? Can I select other pictures for deletion? Can I zoom in on pictures during playback? How do I view a lot of pictures at once? How do I find pictures? Can I protect my pictures from accidental deletion? Can I hide the icons in the display when viewing my pictures? Can I view my pictures in a slide show? Can I add a short voice memo to my pictures? Can I crop unwanted elements out of my pictures? Can I make
Table of Contents Notes and Cautions ........................................................................ ii IMPORTANT SAFETY INSTRUCTIONS ...................................... ii Safety Notes .................................................................................... iv About This Manual ......................................................................... ix Camera Q & A .....................................................................................
Table of Contents Viewing Pictures on a Computer............................................51 Installing the Software...............................................................51 Connecting the Camera ............................................................55 Menuss Menu Using the Menus: Shooting Mode .........................................57 Using the Shooting Menu.........................................................57 Shooting Menu Options ..................................................
Introduction Symbols and Conventions Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the monitor display may be simplified for explanatory purposes. Before You Begin The following symbols are used in this manual: C Caution: This information should be read before use to ensure correct operation. A Note: Points to note when using the camera. B Tip: Additional information that may be helpful when using the camera.
Introduction Parts of the Camera For more information, refer to the page listed to the right of each item. 2 1 3 22 8 7 18 17 16 15 4 14 9 5 10 11 6 1 2 3 4 5 6 7 8 2 19 20 12 21 13 Selector button Move cursor up E l (exposure compensation) button (pg. 28) I (delete) button (pg. 19) MENU/OK button (pg. 12) Move cursor left G L (macro) button (pg. 30) Move cursor right H K (flash) button (pg. 31) Move cursor down F J (self-timer) button (pg. 33) n button .................................
Introduction ■ Shooting * 19 400 F AF 12 / 31 / 2050 10 : 00 AM -1 2 3 250 F3.3 * d: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (pg. 8). 1 2 3 4 5 6 7 8 9 10 11 Internal memory indicator* Focus frame .................................................14 Silent mode indicator............................32 Continuous shooting mode .............61 Intelligent Face Detection indicator ............................................................
Introduction The Mode Dial To select a shooting mode, align the mode icon with the mark next to the mode dial. P (PROGRAM AE): Select for control of camera settings such as exposure compensation, white balance, and ISO sensitivity. The mode automatically sets both shutter speed and lens aperture (pg. 20). A (MOVIE): Record movies with sound (pg. 42). SRC (SCENE RECOGNITION): Select for letting the camera automatically adjust settings to suit the scene (pg. 13).
Charging the Battery The battery is not charged at shipment. Charge the battery before use. Batteries The camera uses an NP-45A rechargeable battery. charger as shown, making sure that the battery is in the orientation indicated by the E F labels. B Battery F label B E B E Charging indicator Arrow F label Battery charger the charger in. 2 Plug Plug the charger into a power outlet. The charging indicator will light. C Cautions • Unplug the charger when it is not in use.
Inserting the Battery After charging the battery, insert it in the camera as described below. 1 Open the battery-chamber cover. A Note Be sure the camera is off before opening the battery-chamber cover. C Cautions • Do not open the battery-chamber cover when the camera is on. Failure to observe this precaution could result in damage to image files or memory cards. • Do not use excessive force when handling the battery-chamber cover. 6 Insert the battery.
Inserting the Battery 3 Close the battery-chamber cover. Battery latch C Caution Turn the camera off before removing the battery. First Steps Removing the Battery After turning the camera off, open the batterychamber cover, press the battery latch to the side, and slide the battery out of the camera as shown. B Tips: Using an AC Adapter • The camera can be powered by an optional AC adapter and DC coupler (sold separately). See manuals provided with the AC adapter and DC coupler for details.
Inserting a Memory Card Although the camera can store pictures in internal memory, SD memory cards (sold separately) can be used to store additional pictures. When no memory card is inserted, d appears in the monitor and internal memory is used for recording and playback.
Inserting a Memory Card ■ Inserting a Memory Card Turn the camera off, and open the battery-chamber cover. 1 3 Close the battery-chamber cover. First Steps C Caution Be sure card is in correct orientation; do not insert at an angle or use force. If the memory card is not inserted correctly, d will appear in the monitor and images will be recorded to internal memory. the memory card firmly until you 2 Insert hear (feel) a click.
Inserting a Memory Card Removing Memory Cards After confirming that the camera is off, press the card in and then release it slowly. The card can now be removed by hand. C Cautions • The memory card may spring out if you remove your finger immediately after pushing the card in. • Memory cards may be warm to the touch after being removed from the camera. This is normal and does not indicate a malfunction.
Turning the Camera on and off Shooting Mode Playback Mode Press the n button to turn the camera on. The lens will extend and the lens cover will open. To turn the camera on and begin playback, press the D button for about a second. B Tip: Switching to Playback Mode Press the D button for about a second to start playback. Press the shutter button halfway to return to shooting mode. C Cautions • Forcibly preventing the lens from extending could cause damage or product malfunction.
Basic Setup A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as described below (for information on resetting the clock or changing languages, see page 77). 1 Choose a language. START MENU ENGLISH FRANCAIS DEUTSCH ESPAÑOL PORTUGUÊS SET NO 1.1 Press the selector up or down to highlight a language. 2.1 Press the selector left or right to highlight the year, month, day, hour, or minute and press up or down to change.
Taking Pictures in SRC (SCENE RECOGNITION) Mode This section describes how to take pictures in SRC (SCENE RECOGNITION) mode. the camera on. 1 Turn Press the n button to turn the the battery level. 3 Check Check the battery level in the display. camera on. q e r Description Battery partially discharged. Battery more than half discharged. Low battery. Charge as soon as possible. Battery exhausted. Turn camera off and charge battery. Basic Photography and Playback Select SRC mode.
Taking Pictures in SRC (SCENE RECOGNITION) Mode a picture using the zoom control. 4 Frame The camera analyzes a subject based on scene recognition, then an icon appears in the bottom left of the monitor. (The illustration shows when the camera analyzed subject(s) in portrait.) Subject Icon PORTRAIT H LANDSCAPE I 14 NIGHT J MACRO K BACKLIT PORTRAIT T NIGHT PORTRAIT Z Description For soft-toned portraits with natural skin tones. For crisp, clear daylight shots of buildings and landscapes.
Taking Pictures in SRC (SCENE RECOGNITION) Mode How to use the zoom control Select B to zoom out 1.6x Select A to zoom in 7.6x Holding the Camera Hold the camera steady with both hands and brace your elbows against your sides. Shaking or unsteady hands can blur your shots. Zoom indicator Basic Photography and Playback To prevent pictures that are out of focus or too dark (underexposed), keep your fingers and other objects away from the lens and flash.
Taking Pictures in SRC (SCENE RECOGNITION) Mode Framing Guideline (Best Framing) In shooting mode, press DISP/BACK to select a shooting display format. The selection changes each time DISP/BACK is pressed. INFORMATION ON INFORMATION OFF BEST FRAMING • Best Framing: To use the best framing, position the main subject at the intersection of two lines or align one of the horizontal lines with the horizon.
Taking Pictures in SRC (SCENE RECOGNITION) Mode Focus. 5 Press the shutter button halfway to focus. If the camera is able to focus, it will beep twice and the indicator lamp will glow green. If the camera is unable to focus, the red colored focus frame and R will appear in the monitor, and the indicator lamp will blink green. Change the composition or use focus lock (pg. 26). Shoot. 6 Smoothly press the shutter button the rest of the way down to take the picture.
Taking Pictures in SRC (SCENE RECOGNITION) Mode The Indicator Lamp Indicator lamp The indicator lamp shows camera status as follows: Indicator lamp Camera status Glows green Focus locked. Blur, focus, or exposure warning. Blinks green Picture can be taken. Blinks green Recording pictures. Additional and orange pictures can be taken. Glows Recording pictures. No additional orange pictures can be taken at this time. Flash charging; flash will not fire Blinks orange when picture is taken.
Viewing Pictures Pictures can be viewed in the monitor. When taking important photographs, take a test shot and check the results. 1 Press the D button. Deleting Pictures To delete the picture currently displayed in the monitor, press the selector up (I). The following dialog will be displayed. The most recent picture will be displayed in the monitor. OK CANCEL SET 100 0001 100-0001 4 0 400 N 12 / 31 / 2050 10 : 00 AM 1/250 F3.3 F3 3 additional pictures.
Shooting Mode Choose a shooting mode according to the scene or type of subject. To choose a shooting mode, rotate the mode dial to the desired setting (pg. 4). The following modes are available: More on Photography 20 SRC SCENE E E RECOGNITION EC A NATURAL & K Simply by pointing the camera to the subject, the camera automatically analyzes and selects the most appropriate setting using scene recognition. See “Taking Pictures in SRC (SCENE RECOGNITION) mode” (pg. 13).
Shooting Mode B NATURAL LL LIGHT G 3 Highlight A SCENE POSITION. Capture natural light indoors, under low light, or where the flash can not be used. The flash turns off and sensitivity is raised to reduce blur. the selector right to display 4 Press shooting mode options. the selector up or down to 5 Press highlight a scene (pg. 23). D/E SCENE POSITION 1 Rotate the mode dial to D/E.
Shooting Mode Y DOG/T CAT (FinePix JZ500/JZ510 series only) When Y DOG or T CAT is selected, the camera detects and focuses the front face of a dog or cat. When Y DOG or T CAT is selected for SCENE POSITION, 5 AUTO RELEASE is available in Self-Timer options. When the camera detects and focuses the face of a dog or cat in 5 AUTO RELEASE, the camera automatically releases the shutter. The detected faces can be used with following functions. • SLIDE SHOW (pg. 69) • IMAGE DISP. > ZOOM(CONTINUOUS) (pg.
Shooting Mode Scene D NIGHT U NIGHT (TRIPOD) W FIREWORKS E SUNSET F SNOW G BEACH I PARTY O FLOWER P TEXT Description Choose for soft-toned portraits with natural skin tones. Choose for a smooth skin effect in soft-focus portraits. Choose for shooting a dog. The mode optimizes to focus on faces of dogs. Choose for shooting a cat. The mode optimizes to focus on faces of cats. Choose for crisp, clear daylight shots of buildings and landscapes. Choose when photographing moving subjects.
B Intelligent Face Detection Intelligent Face Detection allows the camera to automatically detect human faces and set focus and exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for group portraits (in vertical or horizontal orientations) to prevent the camera from focusing on the background. Intelligent Face Detection also offers a red-eye removal option for removing “red-eye” effects caused by the flash. Intelligent Face Detection on. 1 Turn 1.
B Intelligent Face Detection Focus. 3 Press the shutter button halfway to focus on the subject in the green border. Note that, in some shooting modes, exposure is adjusted for the current shooting mode and may not be optimized for the selected subject. Shoot. 4 Press the shutter button all the way down to shoot. C Caution If the subject moves as the shutter button is pressed, their face may not be in the area indicated by the green border when the picture is taken.
Focus Lock To compose photographs with off-center subjects: 1 Position the subject in the focus frame. the picture. 3 Recompose Keeping the shutter button pressed halfway, recompose the picture. Focus. 2 Press the shutter button halfway to set focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). Press halfway 250 F3.3 Repeat steps 1 and 2 as desired to refocus before taking the picture. 26 250 F3 3 F3.3 Shoot.
Focus Lock Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. If the camera is unable to focus using autofocus, use focus lock (pg. 26) to focus on another subject at the same distance and then recompose the photograph. • Very shiny subjects such as mirrors or car bodies. • • • • Subjects photographed through a window or other reflective object.
5 Exposure Compensation Use exposure compensation when photographing very bright, very dark, or high-contrast subjects. the selector up (l). 1 Press The exposure indicator will be displayed. to shooting mode. 3 Return Press MENU/OK to return to shooting mode. 4 Take pictures. SET a value. 2 Choose Press the selector button. The effect is visible in the display.
5 Exposure Compensation Choosing an Exposure Compensation Value • Backlit subjects: choose values from +2/3 EV to +12/3 EV (for an explanation of the term “EV”, see the Glossary on page 100) • Highly reflective subjects or very bright scenes (e.g.
L Macro Mode (Close-ups) For close-ups, press the selector left (L). The selection changes each time the selector is pressed. OFF MACRO When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the zoom control to compose pictures. To exit macro mode, press the selector left (L) and select OFF. Macro mode can also be cancelled by turning the camera off or selecting another shooting mode. A Notes • Use of a tripod is recommended to prevent blur caused by camera shake.
K Using the Flash (Super Intelligent Flash) When the flash is used, the camera’s Super Intelligent Flash system instantly analyzes the scene based on such factors as the brightness of the subject, its position in the frame, and its distance from the camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes.
K Using the Flash (Super Intelligent Flash) Focus. 2 Press the shutter button halfway to focus. If the flash will fire, X will be displayed when the shutter button is pressed halfway. At slow shutter speeds, 0 will appear in the display to warn that pictures may be blurred; use of a tripod is recommended. Shoot. 3 Press the shutter button the rest of the way down to shoot. C Caution The flash may fire several times with each shot. Do not move the camera until shooting is complete.
J Using the Self-Timer The camera offers a ten-second timer that allows photographers to appear in their own photographs, and a two-second timer that can be used to avoid blur caused by the camera moving when the shutter button is pressed. The self-timer is available in all shooting modes. the timer. 1 Set Press the selector down (J). The selection changes each time the selector is pressed. The current self-timer mode is displayed in the monitor.
J Using the Self-Timer The self-timer lamp on the front of the camera will blink immediately before the picture is taken. If the twosecond timer is selected, the self-timer lamp will blink as the timer counts down. Intelligent Face Detection Because it ensures that the faces of portrait subjects will be in focus, Intelligent Face Detection (pg. 24) is recommended when using the self-timer for group portraits or self-portraits.
Playback Options To view the most recent picture in the monitor, press the D button. 100 0001 100-0001 Choosing a Display Format In playback mode, press DISP/BACK to select a playback display format. 400 N 12 / 31 / 2050 10 : 00 AM 1 250 F3.3 1/250 F3 3 The selection changes each time DISP/BACK is pressed. INFORMATION ON INFORMATION OFF 100 0001 100-0001 400 N 12 / 31 / 2050 10 : 00 AM 1/250 F3.
Playback Options Playback Zoom Select A to zoom in on pictures displayed in single-frame playback; select B to zoom out. When the picture is zoomed in, the selector can be used to view areas of the image not currently visible in the display. Zoom indicator Navigation window shows portion of image currently displayed in monitor Press DISP/BACK to exit zoom. A Note Playback zoom is not available with images saved or cropped at the size of t, or copies created with j RESIZE (pg. 72).
Playback Options Multi-Frame Playback y To change the number of images displayed, select B when a picture is shown full-frame in the monitor. 12 / 31 / 2050 B Tip: Two-Frame Display Two-frame display can be used to compare pictures taken in A mode. 10 : 00 AM Select A to reduce the number of images displayed. More on Playback Select B to increase the number of pictures displayed to one frame with previous and next, two, nine, and a hundred.
V Image Search Image Search based on categories Search for pictures by date, subject, scene, and file type. MENU/OK to display the 1 Press playback menu. the selector up or down to 2 Press highlight V IMAGE SEARCH. MENU/OK to display the search 3 Press category. the selector up or down 4 Press to highlight the desired search category. Option BY DATE BY FACE BY SCENE BY TYPE OF DATA 38 Description Show images based on the specified date. Show images based on specified face information.
V Image Search Using g Playback y Menu with Image g Search Three playback menus can be performed with image search mode. MENU/OK while the search 1 Press results are displayed. The playback menu will be displayed. the selector up or down to 2 Press highlight the desired menu item. B Tips • For each operation, refer to the page listed. Option See Page 40 MERASE 70 OPROTECT 69 qSLIDE SHOW More on Playback MENU/OK to select the 3 Press highlighted menu.
M Deleting Pictures The ERASE option in the playback menu can be used to delete still pictures and movies, increasing the amount of space available on the memory card or in internal memory (for information on deleting pictures in single-frame playback, see page 19). Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding. MENU/OK to display the 1 Press playback menu.
M Deleting Pictures ■ FRAME: Deleting Selected Images Selecting FRAME displays the dialog shown at right. ■ ALL FRAMES: Deleting All Images ERASE ALL OK? Selecting ALL FRAMES IT MAY TAKE A WHILE displays the confirmation OK shown at right. CANCEL ERASE OK? YES SET CANCEL Press DISP/BACK to exit when all the desired pictures have been deleted. Highlight OK and press MENU/ OK to delete all unprotected pictures. The dialog shown at right is displayed during deletion.
A Recording Movies Shoot short movies with sound. Sound is recorded via the built-in microphone; do not cover the microphone during recording. Rotate the mode dial to A (movie 1 mode). 12s STAN BY Display shows time available the scene using the zoom 2 Frame control. Movies 42 12s STAN BY Zoom indicator the shutter button all the way 3 Press down to start recording. REC 12s z REC and time remaining are displayed B Tip There is no need to keep the shutter button pressed during recording.
A Recording Movies the shutter button halfway 4 Press to end recording. Recording ends automatically when the movie reaches maximum length or memory is full. C Caution The indicator lamp lights while movies are being recorded. Do not open the battery chamber card during shooting or while the indicator lamp is lit. Failure to observe this precaution could prevent the movie from being played back. Selecting focus mode Select F AF MODE in the shooting menu.
D Viewing Movies During playback, movies are displayed in the monitor as shown at right. The following operations can be performed while a movie is displayed: Operation Start/pause playback End playback/ delete 100 006 100-006 15s 12 / 31 / 2050 PLAY 10 : 00 AM Description Press the selector down to start playback. Press again to pause. Press the selector up to end playback. If playback is not in progress, pressing the selector up will delete the current movie.
Viewing Pictures on TV Connect the camera to a TV and tune the television to the video channel to show pictures to a group. Connect an A/V cable (optional), as shown below. Be sure that the camera is off before connecting the cable. Connect yellow plug to video-in jack Insert an optional A/V cable into the USB multi-connector of the camera. Connect white plug to audio-in jack Press D for about a second to turn the camera on.
Printing Pictures via USB If the printer supports PictBridge, the camera can be connected directly to the printer and pictures can be printed without first being copied to a computer. Note that depending on the printer, not all the functions described below may be supported. Connecting the Camera Printing Selected Pictures the supplied USB cable as shown 1 Connect and turn the printer on. the selector left or right to 1 Press display a picture you wish to print.
Printing Pictures via USB B Tip: Printing the Date of Recording To print the date of recording on pictures, press DISP/BACK in steps 1–2 to display the PictBridge menu (see “Printing the DPOF Print Order,” on pg. 48). Press the selector up or down to highlight PRINT WITH DATE y and press MENU/OK to return to the PictBridge display (to print pictures without the date of recording, select PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures.
Printing Pictures via USB Printing the DPOF Print Order To print the print order created with r PRINT ORDER (DPOF) in the playback menu (pg. 49): In the PictBridge display, press DISP/ 1 BACK to open the PictBridge menu. MENU/OK to display a 3 Press confirmation dialog. PRINT DPOF OK? TOTAL: 9 SHEETS PICTBRIDGE PRINT WITH DATE PRINT WITHOUT DATE PRINT DPOF YES CANCEL 4 Press MENU/OK to start printing. the selector up or down to 2 Press highlight x PRINT DPOF.
Printing Pictures via USB Creating a DPOF Print Order The r PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print order” for PictBridge-compatible printers (pg. 48) or devices that support DPOF. DPOF DPOF (Digital Print Order Format) is standard that allows pictures to be printed from “print orders” stored in internal memory or on a memory card. The information in the order includes the pictures to be printed and the number of copies of each picture.
Printing Pictures via USB steps 1–2 to complete the 3 Repeat print order. Press MENU/OK to save the print order when settings are complete, or DISP/BACK to exit without changing the print order. total number of prints is 4 The displayed in the monitor. Press MENU/OK to exit. The pictures in the current print order are indicated by a x icon during playback. A Notes • Remove the memory card to create or modify a print order for the pictures in internal memory.
Viewing Pictures on a Computer The supplied software can be used to copy pictures to a computer, where they can be stored, viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT connect the camera to the computer until installation is complete. Installing the Software Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh. Installation instructions for Windows are on pages 51–52, those for the Macintosh on pages 53–54.
Viewing Pictures on a Computer 2 Start the computer. Log in to an account with administrator privileges before proceeding. 3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive. Windows 7/Windows Vista If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed; click Yes (Windows 7) or click Allow (Windows Vista).
Viewing Pictures on a Computer Macintosh: Installing FinePixViewer Confirm that the computer meets the following system requirements: 1 CPU PowerPC or Intel Pre-installed versions of Mac OS X version 10.3.9–10.6 (for the latest information, visit http://www.fujifilm. OS com/) RAM 256 MB or more Free disk space A minimum of 200 MB required for installation with 400 MB available when FinePixViewer is running Video 800 × 600 pixels or more with thousands of colors or better • Built-in USB port recommended.
Viewing Pictures on a Computer the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD 4 Remove if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry location out of direct sunlight in case you need to re-install the software. The version number is printed at the top of the CD label for reference when updating the software or contacting customer support. OS X 10.
Viewing Pictures on a Computer Connecting the Camera pictures you wish to copy are stored 1 Ifonthea memory card, insert the card into the camera (pg. 8). If no card is inserted, pictures will be copied from internal memory. A Note Windows users may require the Windows CD when starting the software for the first time. C Caution Loss of power during transfer could result in loss of data or damage to internal memory or the memory card. Charge the battery before connecting the camera.
Viewing Pictures on a Computer C Cautions • If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Using the Menus: Shooting Mode Using the Shooting Menu MENU/OK to display the 1 Press shooting menu. SHOOTING MENU PROGRAM AE ISO IMAGE SIZE IMAGE QUALITY FINEPIX COLOR WHITE BALANCE the selector up or down to 4 Press highlight the desired option. 1/2 AUTO N MENU/OK to select the 5 Press highlighted option. AUTO EXIT the selector up or down to 2 Press highlight the desired menu item. DISP/BACK to exit from the 6 Press menu. A Note Some options are not available in all shooting modes.
Using the Menus: Shooting Mode Shooting Menu Options Menu item Description A SCENE POSITION Choose a scene for D/E mode (pg. 21). n ISO 1/2 o IMAGE SIZE T IMAGE QUALITY Adjust ISO sensitivity (pg. 59). Choose higher values when the subject is poorly lit. Choose image size (pg. 59). Choose image quality (pg. 60). Shoot pictures in standard or saturated color or W FINEPIX COLOR in black-and-white (pg. 60). C WHITE BALANCE Adjust color for different light sources (pg. 61).
Using the Menus: Shooting Mode n ISO Control the camera’s sensitivity to light. Higher values can be used to reduce blur when lighting is poor; note, however, that mottling may appear in pictures taken at high sensitivities. If AUTO is selected, the camera will adjust sensitivity automatically in response to shooting conditions. Settings other than AUTO are shown by an icon in the display. o IMAGE SIZE Choose the size at which still pictures are recorded.
Using the Menus: Shooting Mode Aspect Ratio Pictures with an aspect ratio of 4 : 3 have the same proportions as the camera display. Pictures with an aspect ratio of 3 : 2 have the same proportions as a frame of 35-mm film, while an aspect ratio of 16 : 9 is suited to display on High Definition (HD) devices. T IMAGE QUALITY Choose how much image files are compressed. Select FINE (low compression) for higher image quality, NORMAL (high compression) to increase the number of pictures that can be stored.
Using the Menus: Shooting Mode A Notes • FINEPIX COLOR is not reset when the camera is turned off or another shooting mode is selected. • Depending on the subject, the effects of Mv-CHROME may not be visible in the monitor. C WHITE BALANCE For natural colors, choose a setting that matches the light source (for an explanation of “white balance,” see the Glossary on page 100). Option Description AUTO White balance adjusted automatically. p q s t u r For subjects in direct sunlight.
Using the Menus: Shooting Mode F AF MODE This option controls how the camera selects the focus area. Regardless of the option selected, the camera will focus on the subject in the center of the monitor when macro mode is on (pg. 30). • w CENTER: The camera focuses on the subject in the center of the frame. This option can be used with focus lock. • X TRACKING: When X is set, the focus frame is displayed in the center of the monitor as shown.
Using the Menus: Shooting Mode the selector up or down to 4 Press highlight ON. 5 MENU/OK to display PERSONAL 4 Press INFO. PERSONAL INFO Press MENU/OK to activate S FACE RECOGNITION. NAME BIRTHDAY CATEGORY ■ REGISTER BACK Shooting REGISTER from S FACE 1 Select RECOGNITION. MENU/OK to turn to shooting 2 Press mode. 3 2050. 12. 31 NONE Press the shutter button to shoot. Capture a front face. Registering a name the selector up or down to 1 Press highlight NAME in PERSONAL INFO.
Using the Menus: Shooting Mode the selector left, right, up or 3 Press down to highlight a letter. 4 Press MENU/OK to input the letter. from step 2 to step 4 to input a 5 Repeat name. the selector left, right, up or 6 Press down to highlight SET. 7 Press MENU/OK to register. A Notes • Highlight DEL and press MENU/OK to erase a letter. • Highlight g and press MENU/OK to put a space. • Up to 14 letters can be displayed.
Using the Menus: Shooting Mode 3 Press MENU/OK to register. the registration or edit as the same 4 View way of REGISTER (pg. 63). ■ VIEW & EDIT A Note Select REPLACING IMAGE to take another face image and replace the registered image with it. VIEW & EDIT from S FACE 1 Select RECOGNITION to display REGISTERED FACE. REGISTERED FACE SET 2 ■ ERASE 1 Select ERASE from S FACE RECOGNITION. the selector left or right to 2 Press highlight a face to erase.
Using the Menus: Shooting Mode MENU/OK to delete a 5 Press registration. ■ AUTO REGISTRATION Select AUTO REGISTRATION from S FACE RECOGNITION and set it to ON. After shooting the same face several times with 3 FACE DETECTION turned on, the camera automatically recognizes the face. A Notes • When the camera recognizes a face that has been shot many times, the message REGISTER THIS PERSON? appears. Press MENU/OK to display PERSONAL INFO so that you can register the face and its personal information.
Using the Menus: Playback Mode Using the Playback Menu D to enter playback mode 1 Press (pg. 11). PLAYBACK MENU MENU/OK to display the 2 Press playback menu. PLAYBACK MENU the selector right to display 4 Press options for the highlighted item. 1 /2 IMAGE SEARCH ERASE SLIDE SHOW RED EYE REMOVAL PROTECT CROP EXIT the selector up or down to 3 Press highlight the desired menu item. 1 /2 IMAG BACK ERAS SLIDE FRAME RED ALL FRAMES PROT CROP the selector up or down to 5 Press highlight the desired option.
Using the Menus: Playback Mode Playback Menu Options The following options are available: Option V IMAGE SEARCH M ERASE q SLIDE SHOW 1/2 a RED-EYE REMOVAL O PROTECT R CROP j RESIZE N IMAGE ROTATE P COPY Q VOICE MEMO 2/2 S ERASE FACE RECOG. (FinePix JZ500/ JZ510 series only) r PRINT ORDER (DPOF) 68 Description Search images based on categories (pg. 38). Delete all or selected pictures (pg. 40). View pictures in a slide show (pg. 69). Create copies with reduced red eye (pg. 69).
Using the Menus: Playback Mode q SLIDE SHOW View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press DISP/BACK at any time during the show to view on-screen help. When a movie is displayed, movie playback will begin automatically, and the slide show will continue when the movie ends. The show can be ended at any time by pressing MENU/OK. Displayed in Press selector left or right to go back or skip ahead one frame.
Using the Menus: Playback Mode O PROTECT Protect pictures from accidental deletion. The following options are available. ■ FRAME Protect selected pictures. the selector left or right to 1 Press display the desired picture. PROTECT OK? YES UNPROTECT OK? CANCEL Picture not protected YES CANCEL Protected picture MENU/OK to protect the 2 Press picture. If the picture is already protected, pressing MENU/OK will remove protection from the image. steps 1–2 to protect 3 Repeat additional images.
Using the Menus: Playback Mode R CROP To create a cropped copy of a picture, play the picture back and select R CROP in the playback menu. 1 Use the zoom control to zoom in and out and use the selector to scroll the picture until the desired portion is displayed (to exit to singleframe playback without creating a cropped copy, press DISP/BACK). B Tip: Intelligent Face Detection If the picture was shot with Intelligent Face Detection (pg. 24), B will be displayed in the monitor.
Using the Menus: Playback Mode j RESIZE To create a small copy of a picture, play the picture back and select j RESIZE in the playback menu. the selector up or down 1 Press to highlight t STANDARD or s SMALL. MENU/OK to select the 2 Press highlighted option. MENU/OK to copy the picture at 3 Press the selected size. N IMAGE ROTATE IMAGE ROTATE By default, pictures taken in tall orientation are displayed in wide orientation.
Using the Menus: Playback Mode the selector down to 1 Press rotate the picture 90 ° clockwise, up to rotate the picture 90 ° counterclockwise. P COPY Copy pictures between internal memory and a memory card. the selector up or down to 1 Press highlight d INTERNAL MEMORY g x CARD (copy pictures from internal memory to the memory card) or x CARD g d INTERNAL MEMORY (copy pictures from a memory card to internal memory). the selector right to display 2 Press options for the highlighted item.
Using the Menus: Playback Mode B Tip: Copying Pictures Between Memory Cards To copy pictures between two memory cards, insert the source card and copy the pictures to internal memory, then remove the source card, insert the destination card, and copy the pictures from internal memory. ■ ALL FRAMES Press MENU/OK to copy all pictures, or press DISP/BACK to exit without copying pictures. ■ FRAME Copy selected frames. C Cautions • Copying ends when the destination is full.
Using the Menus: Playback Mode Q VOICE MEMO To add a voice memo to a still picture, select Q VOICE MEMO after displaying the picture in playback mode. 30s REC STANDBY 28s RECORDING START Hold the camera at a distance of about 20 cm (8 in.) and face the microphone. Microphone Time remaining Blinks red CANCEL A Note Voice memos can not be added to movies or protected pictures. Remove protection from pictures before recording voice memos (pg. 70). 1 2 Press MENU/OK to start recording.
Using the Menus: Playback Mode Playing Voice Memos Pictures with voice memos are indicated by a h icon during playback. To play the voice memo, Select PLAY. To pause, press the selector down; to end playback, press the selector up. Press the selector left to rewind, right to fast forward. Volume controls can be displayed by pressing the MENU/OK button; press the selector up or down to adjust the volume, and press MENU/OK again to resume playback. 15s Progress is shown in the monitor.
The Setup Menu Using the Setup Menu the setup menu. 1 Display 1.1 Press MENU/OK to display the 2.2 Press the selector up or down to highlight a menu item. menu for the current mode. SET UP 1.2 Press the selector left to highlight a left tab. 1.3 Press the selector up or down to select 4. The setup menu appears. SET UP 1 /4 DATE/TIME TIME DIFFERENCE SILENT MODE RESET FORMAT ENGLISH OFF EXIT Adjust settings. 2 2.1 Press the selector right to SILENT MODE RESET FORMAT ENGLISH OFF EXIT 2.
The Setup Menu Setup Menu Options Menu item e DATE/TIME p TIME DIFFERENCE nw 7 SILENT MODE 1/4 s RESET m FORMAT a IMAGE DISP. 2/4 b FRAME NO. d OPERATION VOL. e SHUTTER VOLUME f SHUTTER SOUND g PLAYBACK VOLUME 78 Description Set the camera clock. Set the clock to local time (pg. 80). Choose a language. Turn off the speaker, flash, and self-timer lamp. Reset all settings except DATE/TIME, TIME DIFFERENCE, BACKGROUND COLOR, and VIDEO SYSTEM to default values.
The Setup Menu Menu item g LCD BRIGHTNESS d LCD MODE o AUTO POWER OFF 3/4 Z DUAL IS MODE a RED EYE REMOVAL c DIGITAL ZOOM R SAVE ORG IMAGE 4/4 q BACKGROUND COLOR u GUIDANCE DISPLAY r VIDEO SYSTEM Description Control the brightness of the display (pg. 83). Enable or disable monitor power saving (pg. 83). Choose the auto power off delay (pg. 83). Reduce blur.
The Setup Menu p TIME DIFFERENCE When traveling, use this option to switch the camera clock instantly from your home time zone to the local time at your destination. the difference between local time 1 Specify and your home time zone. 1.1 Press the selector up or down to highlight j LOCAL. 1.2 Press the selector right to display the time difference. TIME DIFFERENCE 12 / 31 / 2050 10:00 AM 12 / 31 / 2050 10:00 AM between local time and your 2 Switch home time zone.
The Setup Menu m FORMAT FORMAT Format internal memory or a FORMAT OK? ERASE ALL DATA memory card. If a memory OK card is inserted in the camera, CANCEL x will be displayed in the SET dialog shown at right and this option will format the memory card. If no memory card is inserted, d will be displayed and this option will format internal memory. Highlight OK and press MENU/OK to begin formatting. C Cautions • All data—including protected pictures—will be deleted.
The Setup Menu ZOOM (CONTINUOUS) is disabled in the following case: - A is selected in the shooting mode. - An option other than OFF is selected for E CONTINUOUS. A Notes • Pictures taken in continuous shooting modes are always displayed after shooting. • The colors displayed at settings of 1.5 SEC and 3 SEC may differ from those in the final picture. b FRAME NO.
The Setup Menu g PLAYBACK VOLUME Press the selector up or down to choose volume for movie and voice memo playback and press MENU/OK to select. g LCD BRIGHTNESS Press the selector up or down to choose display brightness and press MENU/OK to select. VOLUME 7 SET CANCEL LCD BRIGHTNESS 0 SET CANCEL d LCD MODE Control the quality of the display in the monitor. Choose i for improved display quality, h for increased battery life.
The Setup Menu c DIGITAL ZOOM If ON is selected, selecting A at the maximum optical zoom position will trigger digital zoom, further magnifying the image. To cancel digital zoom, zoom out to the minimum digital zoom position and select B. Zoom indicator Zoom indicator, DIGITAL ZOOM off B A B Optical zoom 84 Zoom indicator, DIGITAL ZOOM on Optical zoom A Digital zoom C Caution Digital zoom produces lower quality images than optical zoom.
Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. ■ Computer Related ■ Audio/Visual TV* USB Audio/visual output HDTV* Computer* HD player SD/SDHC memory card HDMI cable* Printer* USB Technical Notes ■ Printing SD card slot or card reader PictBridge-compatible printer* * Available from third-party suppliers.
Optional Accessories Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www. fujifilm.com/products/digital_cameras/index.html. 86 Rechargeable Li-ion battery NP-45 Additional NP-45 large-capacity batteries can be purchased as required. Battery charger BC-45W (supplied) Replacement battery chargers can be purchased as required.
Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. ■ Water and Sand Exposure to water and sand can also damage the camera and its internal circuitry and mechanisms. When using the camera at the beach or seaside, avoid exposing the camera to water or sand. Do not place the camera on a wet surface. ■ Condensation Sudden increases in temperature, such as occur when entering a heated building on a cold day, can cause condensation inside the camera.
Troubleshooting Power and Battery Problem Possible cause The battery is exhausted. The battery is not in the correct The camera does orientation. not turn on. The battery-chamber cover is not latched. The AC adapter and DC coupler are not connected properly. Power supply Troubleshooting 88 Solution Insert a fresh or fully-charged spare battery. Re-insert the battery in the correct orientation. Latch the battery-chamber cover. Make sure that the AC adapter and DC coupler are properly connected.
Troubleshooting Problem Battery charger Possible cause The battery is not correctly inserted. Charging does The battery is not in the correct not start. orientation. Charging is slow. The temperature is low. There is dirt on the battery terminals. Solution Re-insert the battery in the charger. Re-insert the battery in the correct orientation. Charge the battery at room temperature. Clean the terminals with a soft, dry cloth. The battery has reached the end of its The charging charging life.
Troubleshooting Shooting Problem Possible cause Solution Page Memory is full. Insert a new memory card or delete pictures. 8, 40 Memory is not formatted. Format the memory card or internal memory. 81 No picture is — taken when the There is dirt on the memory card contacts. Clean the contacts with a soft, dry cloth. shutter button is The memory card is damaged. Insert a new memory card. 8 Taking pressed. The battery is exhausted. Insert a fresh or fully-charged spare battery.
Troubleshooting Problem Turn silent mode off. 32 The flash does not fully light the subject. There is a dark part on the fringe of an image. The subject is not in range of the flash. Position the subject in range of the flash. 103 The flash window is obstructed. Hold the camera correctly. 15 The image was taken in a very dark location selecting B (wide angle) to zoom. Take a shot selecting A (telephoto). 15 Help text is displayed. The camera was turned on while being powered by an AC adapter.
Troubleshooting Problem Pictures are blurred. Problem images Pictures are mottled. Vertical lines appear in pictures. Possible cause The lens is dirty. The lens is blocked. R is displayed during shooting and the focus frame is displayed in red. 0 is displayed during shooting. The ambient temperature is high and the subject is poorly lit. 92 Pictures are not recorded. Power was interrupted during shooting. Page 87 15 Check focus before shooting. 17 Use the flash or a tripod.
Troubleshooting Movie Problem Possible cause T CONTINUOUS is selected for F AF The sound of Recording camera focusing MODE. is heard. Zoom in or out while recording a movie. Solution Page Select w CENTER for F AF MODE. 43 Stop zoom operation. 42 Playback Problem Prob em Pictures are grainy. Solution Page — — — 35, 72 Turn silent mode off. Adjust playback volume. Hold the camera correctly during recording. Hold the camera correctly during playback.
Troubleshooting Connections Problem Prob em Poss ble cause Possible Monitor is off. The camera is connected to a TV. The camera is not properly connected. An A/V cable was connected during movie playback. No picture or Input on the television is set to “TV”. sound. TV The camera is not set to the correct video standard. The volume on the television is too low. The camera is not set to the correct video No color. standard. The computer does not The camera is not properly connected.
Troubleshooting Miscellaneous Prob em Problem Nothing happens when the shutter button is pressed. Poss ble cause Possible Temporary camera malfunction. The battery is exhausted. The camera does not Temporary camera malfunction. function as expected. Solution Remove and reinsert the battery or disconnect and reconnect the AC adapter/ DC coupler. Insert a fresh or fully-charged spare battery. Remove and reinsert the battery or disconnect and reconnect the AC adapter/ DC coupler.
Warning Messages and Displays The following warnings are displayed in the monitor: Warning O (red) N (blinks red) 0 Description The battery is low. The battery is exhausted. Slow shutter speed. Picture may be blurred. R (displayed in red The camera can not focus. with red focus frame) Aperture or shutter speed shown in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN NO CARD The subject is too bright or too dark. The picture will be over- or under-exposed. Camera malfunction.
Warning Messages and Displays Warning CARD ERROR Descript on Description The memory card is not formatted for use in the camera. Format the memory card (pg. 81). Clean the contacts with a soft, dry cloth. If the The memory card contacts require cleaning or message is repeated, format the memory card (pg. 81). the memory card is damaged. If the message persists, replace the memory card. Incompatible memory card. Use a compatible memory card. Camera malfunction. Contact a FUJIFILM dealer.
Warning Messages and Displays Warning FRAME NO. FULL Descript on Description The camera has run out of frame numbers (current frame number is 999-9999). An attempt was made to execute IMAGE SEARCH over too many pictures. CAN NOT EXECUTE Red-eye removal can not be applied to the A CAN NOT EXECUTE selected picture or movie. An attempt was made to delete, rotate, or add PROTECTED FRAME a voice memo to a protected picture. Voice memo file is corrupt. 5 ERROR Camera malfunction.
Warning Messages and Displays Warning CAN NOT SET DPOF A CAN NOT SET DPOF CAN NOT ROTATE A CAN NOT ROTATE PRESS AND HOLD THE DISP BUTTON TO DEACTIVATE SILENT MODE Descript on Description The picture can not be printed using DPOF. Movies can not be printed using DPOF. The picture is protected. Movies can not be rotated. An attempt was made to choose a flash mode or adjust the volume with the camera in silent mode.
Glossary Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details visible using optical zoom are simply enlarged, producing a slightly “grainy” image. DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored in internal memory or on a memory card. The information in the order includes the pictures to be printed and the number of copies of each picture.
Internal Memory/Memory Card Capacity The following table shows the recording time or number of available frames at different image qualities. You can take a few pictures for trial without a memory card. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate. ■ FinePix JZ500/JZ510 Series i Internal memory (approx.
Internal Memory/Memory Card Capacity ■ FinePix JZ300/JZ310 Series y Internal memory (approx.
Specifications System Model Effective pixels CCD Storage media File system Appendix FinePix JZ500/JZ510 Series FinePix JZ300/JZ310 Series 14.1 million 12.1 million ½.3 -in., square-pixel CCD with primary color filter • Internal memory (approx. 40 MB) • SD/SDHC memory cards (see page 8) Compliant with Design Rule for Camera File System (DCF), Exif 2.2, and Digital Print Order Format (DPOF) File format • Still pictures: Exif 2.
Specifications System Scene modes A (NATURAL AND FLASH LIGHTING), B (NATURAL LIGHT), U (PORTRAIT), V (PORTRAIT ENHANCER), Y* (DOG), T* (CAT), K (LANDSCAPE), L (SPORT), D (NIGHT), U (NIGHT (TRIPOD)), W (FIREWORKS), E (SUNSET), F (SNOW), G (BEACH), I (PARTY), O (FLOWER), P (TEXT) * FinePix JZ500/JZ510 series only Picture stabilization Optical stabilization (CCD shift) Intelligent Face Detection Available Shutter speed ¼ s– ½,000 s (AUTO mode); 4 s–1/1,400 s (other modes); combined mechanical and electronic s
Specifications System Movies Shooting options Playback options Other options Input/output terminals A/V OUT (audio/video output) Digital input/output • ) (1280 × 720: 720p), 24fps • ! (640 × 480: VGA), 30fps • 9 (320 × 240: QVGA), 30fps Scene recognition, Face recognition (FinePix JZ500/JZ510 series only), Dog/Cat detection (FinePix JZ500/JZ510 series only), Intelligent Face Detection with red-eye removal, framing guideline, frame number memory, FINEPIX COLOR Intelligent Face Detection, red-eye removal,
Specifications Power supply/other Power supply Guide to the number of available frames for battery operation Camera dimensions (W × H × D) Camera weight Shooting weight Operating conditions 106 NP-45A rechargeable battery; optional AC power adapter AC-5VX and DC coupler CP-45 Battery Type NP-45A Number of frames Approx.
Specifications NP-45A rechargeable battery Nominal voltage DC 3.7 V Nominal capacity 720 mAh Operating temperature 0 °C – +40 °C/+32 °F – +104 °F Dimensions (W × H × D) 31.0 mm × 39.6 mm × 6.0 mm/1.2 in. × 1.6 in. × 0.2 in. Weight Approx. 15 g/0.5 oz. BC-45W battery charger Rated input Input capacity Rated output Supported batteries Charging time Dimensions (W × H × D) Weight Operating temperature 100 V–240 V AC, 50/60 Hz 8.0 VA (100 V) 12 VA (240 V) 4.
Specifications Color Television Systems NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in European countries and China. Notices • Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.