Owner manual

ManualsBrandsWarmlyYours ManualsHardwareJSR00

Free Design Service • 24/7 Installation Support • (800) 875-5285 • www.WarmlyYours.com

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury

and/or property damage. Retain instructions for future reference.

ET-PWR-END-KIT Installation Instructions

(part #JSR00)

Description: The ET-PWR-END-KIT power connection kit (part #JSR00) is suitable for use only with the ET-SR series heating cables.

The kit provides material for one power connection and one termination.

The ET-SR series cables can be used for pipe freeze protection and/or roof and gutter deicing.

This manual includes installation instructions for the ET-PWR-END-KIT and the ET-END-KIT End Seal Kit (part #JSR12).

Summary of content (8 pages)

PAGE 1
ET-PWR-END-KIT Installation Instructions (part #JSR00) Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference.
PAGE 2
ET-PWR-END-KIT Installation Instructions ET-PWR-END-KIT Assembly Tools Needed • Utility knife • Wire cutter • Needle-nose pliers • Adjustable wrench • Pen • Screwdriver • Heat gun • Measuring tape General Safety Information Read and understand all instructions in this manual, including all installation instructions and safety warnings, before beginning the installation. Electrical cables can present a fire, shock, and arcing hazard if they are damaged or not installed correctly. 1.
PAGE 3
ET-PWR-END-KIT ET-PWR-END-KIT Installation Instructions J C D G F A CAUTION: ELECTRIC DEICING AND SNOW MELTING EQUIPMENT ON THE PREMISES! H WARNING E I FIRE AND ELECTRIC SHOCK ELECTRICALLY HEAT TRACED! DISCONNECT BEFORE SERVICE! B Item Description Quantity A Black Shrinkable Tubing (1/8 in. × 5 ½ in. ) 2 B Green/Yellow Shrinkable Tubing (1/4 in. × 6 in. ) 1 C Seal Fitting and White Grommet 1 D Lock Nut 1 E Black Shrinkable Tubing (1/2 in. × 1 in.
PAGE 4
ET-PWR-END-KIT Installation Instructions ET-PWR-END-KIT Power Connection Kit Installation Instructions Structure of model ET-SR 1. After the seal fitting is open, put the junction box cap, strain relief disk, grommet, and body onto the power connection of cable. 4. Bend heating cable as shown in Figure 4, so it can be pushed through the braid opening. 2. Slice completely around heating cable outer jacket, and then down a distance of approximately 7 inches (178mm).
PAGE 5
ET-PWR-END-KIT Installation Instructions ET-PWR-END-KIT Power Connection Kit Installation Instructions (continued) 10. Carefully shrink tubing by continuously moving the heat source back and forth to heat evenly. Be careful not to damage heating cable. 17. Use a metallic junction box to ensure a proper grounding. Insert heating cable and tighten. NOTE: For ET-SR-240 heating cables, when used in wet locations, follow instructions provided with junction box to seal out water. 14.
PAGE 6
ET-END-KIT End Seal Kit Installation Instructions (part #JSR12) Free Design Service • 24/7 Installation Support • (800) 875-5285 • www.WarmlyYours.
PAGE 7
ET-END-KIT ET-END-KIT Installation Instructions C A B Item Description Quantity A Heat-Shrink Tube (5 in. long x ¾ in. dia.) 1 B Woven Braid Sleeving (4 in. long x ½ in. dia.) 1 C Heat-Shrink Cap (½ in. dia) 1 WARNING: ELECTRIC SHOCK HAZARD: Disconnect all power before installing or servicing heating cable and accessories. A qualified person must perform installation and service of heating cable and accessories.
PAGE 8
ET-END-KIT Installation Instructions ET-END-KIT END SEAL KIT INSTALLATION INSTRUCTIONS 1. Score the outer jacket 2 in. from the end of the cable. Remove the jacket to expose the braid. CAUTION: When removing the outer jacket, be careful not to damage the braid or the base cable insulation. 7. Apply heat evenly to the heat shrink tube until it shrinks around the cable. 4. Pull the pushed-back braid over the sealed end cap and twist the braid end together. 8.