Owner manual

ManualsBrandsWarmlyYours ManualsSensorsTH115 -F-120GA

Table Of Contents

TH115 -F-120GA

Owners Guide

Buttons and symbols

On/Stand By Switch

Use this switch to put the thermostat in sleep mode

when its use is no longer required (e.g. summer).

This will not affect the clock programming.

GFCI Warning Light and Test Button

Day & Clock Settings

Programming Mode

Mode Selection/Exit Programming

Floor/Ambient (Amb. only with B)

Current Mode Auto, Manual, Vacation

Current Program Number

Setpoint definition/Pre-defined Setpoints

Increase/Decrease Temperature

TH115 Description

Align the bracket tabs on the control module with the

holes located on top of the power base.

NOTE: Keep the thermostat’s air vents clean and free

NOTE: The screw cannot be removed completely.

Control Module Installation

Power base

Control module

from obstructions.

Thank you for choosing the AubeTH115 a programmable

thermostat that provides both energy savings and comfort

When power is applied for the first

time, the LCD dispays: 0:00, MO

(Monday), and temperature of the

floor .

Press HOUR - MIN to set the

current time.

Press DAY to set current day.

For AF and F models: one of the two

LO: The floor temperature is below

32ºF (0ºC), or the temperature

sensor is defective, or not con-

nected.

The heating indicator i is dis-

played and the relay is closed

(energized).

HI: The floor temperature is above

140°F (60°C), or the tempea-

ture sensor is defective.

Correct

Incorrect

First Power ON

following messages may be displayed

if the installation is incorrect:

24/7 Installation Support • Lifetime Technical Assistance • Free Design Service • www.WarmlyYours.com • (800) 875-5285

10103-A 04/08

Summary of content (4 pages)

PAGE 1
TH115 -F-120GA Owners Guide Control Module Installation Thank you for choosing the AubeTH115 a programmable thermostat that provides both energy savings and comfort Align the bracket tabs on the control module with the holes located on top of the power base. Control module F Power base NOTE: Keep the thermostat’s air vents clean and free from obstructions. NOTE: The screw cannot be removed completely.
PAGE 2
Operating Modes GFCI Test (GA & GB power baseonly) The GFCI monitors the electrical flow for any loss of current; if there is one, the thermostat will cut off power to the heating system. We recommend you test the GFCI immediately after installing the control module, and once a month thereafter to ensure it is operating properly. To test: Automatic —Executes the schedule. F Press MODE until is displayed. The current program number is displayed.
PAGE 3
Modify the Schedule Notes: You can program up to 4 different programs per day. Each day can have different programs. It is sometimes faster to program the same schedule for the entire week and then to modify the exception days. To modify: 1 to 20% 21 to 40% 41 to 60% 61 to 80% 81 to 100% Technical Support Model: TH115 A / AF / F Display range: 32°F to 140°F (0°C to 60°C) Press DAY to select the day to be programmed (hold for 3 seconds to select all days of the week).
PAGE 4
Technical Support Model: TH115 A / AF / F Display range: 32°F to 140°F (0°C to 60°C) If you have any questions concerning the installation or programming of the TH115 programmable thermostat, call our technical support team at: 800.875.5285 Setting range (ambient): 40°F to 86°F (5°C to 30°C) Setting range (floor limit): 40°F to 104°F (5°C to 40°C) Pre-programmed temperature setpoints: Comfort: For more information on our products, visit us at: www.warmlyyours.