TempZone™ Electric Radiant Floor Heating System (Twin Conductor) Installation Manual Free Design Service • 24/7 Installation Support • (800) 875-5285 • www.WarmlyYours.
Understanding The System How The System Works You can feel the heat of a campfire even though you are not directly above it. Radiant energy transfer is caused by a warm surface (the campfire) giving up its heat to a cooler surface (your body). This radiant energy travels through space without heating the space itself. It only turns into heat when it contacts a cooler surface. By transferring this heat to all of the objects in the room, the heat slowly moves to warm the air which starts to rise.
Items Needed For The System Installation System Components From WarmlyYours 1. The Customized Installation Plan (or layout). 2. Heating Roll(s) (15-watt/ sq. ft.) If multiple rolls are connected to the same control device, they must be of the same voltage type and wired in parallel. 3. Thermostat 4. You may also have a relay contactor or power module, if your system is being installed in a large area.
Understanding the Customized Installation Plan The Customized Installation Plan A. Starting Point: This is your key to a successful installation. Your plan has been custom designed for your individual project based on the dimensions you gave us. It will indicate the placement of each Heating Roll, the electrical service requirements, and the location of the control device(s).
WarmlyYours Floor Heating System. The Heating Roll A. Heating Element B. Fiberglass Mesh C. Tape D. Cold Lead Wire E. Factory Splice F. Floor Sensor (optional) Secondary Flouropolymer Insulation Relay Contactor or Power Modules (not required for all systems) E F Metal Braiding Connected to Ground Systems installed in large spaces will most likely require a Relay Contactor or Power Module(s) in addition to the control device to operate properly.
One Good Turn Deserves Another The complimentary Installation Plan provided by the WarmlyYours team is very important. It shows the recommended placement of your Heating Roll(s) for safety and optimal efficiency. The plan will also serve as the reference for any future inspections or floor work that needs to be performed. The Heating Element of the WarmlyYours product is sewn in a serpentine pattern onto lengths of Fiberglass Mesh forming a roll. It is quick and simple to cover large areas.
One Good Turn Deserves Another Step Turn Step Turn with Flip Over Start Start Working around Obstacles Special circumstances will require the Heating Element to circumvent an obstacle. The released Heating Element is not needed to fill an area but to simply continue the circuit. Experience is the Key As you begin to work with the Heating Panels, you will become more comfortable with the product.
Testing DO NOT SUPPLY THE SYSTEM WITH ELECTRIC CURRENT Go by the Numbers All testing is done with a digital Ohmmeter. Supplying the system with a 120 volt or 240 volt electric current before the installation is complete is not needed to test the system. Taking the Ohm Readings The electrical resistance of the Heating Roll(s) must be checked before you start, and monitored throughout the installation process to ensure there has been no damage causing shorts or breaks.
Example of Wiring a Control to Twin Conductor Conductor REAR OF THE BASE HOUSE GROUND COLD LEAD FLOOR BLACK WIRE BRAIDED GROUND SHEATH LOAD 4 RED 240V or YELLOW 120V 1 1800W/3600W MAX 15A 120/240VAC L2(N) LINE L1(L) 2 3 FROM POWER SOURCE in the wallbox. HOT FRONT OF THE BASE in / sensor HOT (240V) or NEUTRAL (120V) out 6. Turn on breaker.
Installer’s Guide STEP 1 STEP 2 STEP 3 Electrical Planning Prepare the Subfloor Mark the Floor The power supply to the Floor Heating System and the control device will be located at the same point in the room and indicated on your plan. If this location has changed, call WarmlyYours to determine if this will require a new Installation Plan. The lead wire is 15’ long. You can relocate the control device as long as your leads reach the new location. Inspect the subfloor surface carefully.
Ceramic Tile & Natural Stone Floors - Step-by-Step Installation Guide Materials and Tools Required: • WarmlyYours TempZone Heating Rolls • Thermostat with Sensor Probe Wire (if applicable) Preparation: 1. Cross check the items you received against the packing list and the materials list on the installation plan to ensure that the roll length and thermostat type are an exact match. • Circuit Check (sold separately) 2.
Ceramic Tile & Natural Stone Floors - Cont. STEP 1 STEP 2 STEP 3 STEP 4 Dry-Fit / Cutting & Turning Install Warmlyyours Heating Rolls Tile Installation Electrical Connections 1. Verify that the cold lead wires at the end of each roll will reach the thermostat location. Run the cold lead wires no closer than 1” from the edge of the warming roll. Cold lead wires cannot cross over a warming cable or the sensor wire (if applicable).
Glue Down Laminate, Engineered Wood, Vinyl, Carpet and LVT Floors - Installation Guide Materials and Tools Required: • WarmlyYours TempZone™ Heating Rolls • Thermostat with Sensor Probe Wire • Custom Design Layout (provided free with quote) • Digital Ohm Meter (required for completion of warranty registration card) • Circuit Check (sold separately) • Scissors • Staple Gun or Hot Glue Gun (concrete applications) • Duct Tape or Box Tape • Latex-Portland Cement (acrylic or latex modified thin-set mortar) • Pla
Glue Down Laminate, Engineered Wood, Vinyl, Carpet and LVT Floors - Installation Guide STEP 1 Install WarmlyYours Heating Rolls 1. Install the floor heating system as recommended, adhering the mesh every 6-8 inches with hot glue (or staples if using cork insulation), carefully routing the power leads alongside the system back to the power supply. Never staple directly over the wires. 2.
Nailed Hardwood Flooring - Installation Guide STEP 1 Install Wood Sleepers Install wood sleepers (strips of wood 1” to 2” wide and 3/8” to 1/2” high) 19” apart across the entire plywood subfloor leaving appropriate space for any planned cuts and turns. The sleepers are installed to create lanes into which the 18” wide warming system roll will be placed. STEP 2 Lay The Cable Heating System) Lay the floor heating system into the 19” lanes created by the sleepers.
Shower Mat (Bench & Floor) - Installation Guide STEP 1 STEP 2 Once the mortar bed has set, dry fit the TempZone™ Shower Mat to verify its dimensions and ensure it fits the contours of the shower area. Attach the mat to the subfloor using hot glue.Prepare the latex-modified thinset. Using a flat trowel, spread a coat of thinset over the installed mat. Conduct insulation & resistance tests. Record readings on the warranty card found inside the TempZone™ Installation instructions.
Electrician’s Guide – Trouble Shooting “Beware of Using a Continuity Checker!” Our smaller Heating Rolls have a high Ohm resistance and some continuity checkers do not send enough current to get completely through the wire and emit the noise or light that affirms proper continuity. If your instrument cannot function on a small Heating Roll, please use a digital Ohm meter. Electrical Fault-Finding Once the system has been turned off and made safe, have a suitably qualified person: 1.
Important General Considerations IMPORTANT INFORMATION The most important consideration is to maintain the integrity of the Heating Element; following these simple rules can easily do this: 1. NEVER CUT the Heating Element. 2. NEVER CUT the Heating Roll(s) to make it shorter. 3. NEVER fold or position the Heating Element so that it overlaps itself or other wires. The heating portion of the heating device set shall not touch, cross over, or overlap itself. This will cause dangerous overheating. 4.
Warranty Information Please complete and return the Warranty Card (online or you may send/fax this form) Thank you for purchasing your new WarmlyYours TempZone™ floor warming system. To register your system, go online to www.WarmlyYours.com/warranty, or simply complete, detach and mail the Warranty Card within 30 days of date of purchase to: WarmlyYours, 590 Telser Rd Lake Zurich, IL 60047. For your convenience, you may also fax this card to (800) 408-1100. 1. HOMEOWNER INFORMATION 4.
NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES B U S I N E S S R E P LY M A I L FIRST-CLASS MAIL PERMIT NO 77 LONG GROVE IL POSTAGE WILL BE PAID BY ADDRESSEE WarmlyYours Inc 590 Telser Rd Ste B Lake Zurich, IL 60047
