Installation & Operation Manual for WarmlyYours Towel Warmers
Thank you for choosing your finely crafted WarmlyYours Towel Warmer. Now you can add luxury and comfort to your bathroom with the soothing embrace of a warm towel or bathrobe upon stepping from the shower. The radiant heat from the Towel Warmer warms your towel. Included in this document are all necessary installation and operation instructions. For model number, reference the location of the product label as shown in Diagram A on page 11.
Affixing the Towel Warmer to the Wall Step 1 Draw a diagram of the preferred location of the brackets and the electrical connection on the Towel Warmer box to create a template (see Step 2 for template instructions). At least two of the four brackets must be attached directly to a stud. Step 2 Create the template: A. Attach brackets into desired positions on the Towel Warmer (see pages 3-4 for bracket assembly for each model). B.
Affixing the Towel Warmer to the Wall - cont’d Note: Dimensions shown are distances between the center of anchor points. This example shows 16” on center construction. Your situation may vary depending on your stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
Affixing the Towel Warmer to the Wall - cont’d Note: Dimensions shown are distances between the center of anchor points. This example shows 16” on center construction. Your situation may vary depending on your stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
Affixing the Towel Warmer to the Wall - cont’d Step 4 Attach all four brackets to their desired positions on the Towel Warmer. See pgs. 6-8 for bracket assembly instructions specific to the model you selected. Step 5 Lay the template on a flat surface and place the Towel Warmer on top with brackets facing downwards. Mark the exact location of the electrical collar connection and the brackets. Step 6 Use the template as a guide to mark the wall with the correct locations of the four brackets.
Bracket Assembly Diagrams - Portofino A B 4x 4x C D * d e f g h 4x 4x 8x 4x 4x 4x i J K 4x 1x Portofino a. 0002-52110-0000 Clamp, threaded, portofino, Chrome b. 0002-52110-0001 Clamp, Non-Threaded, Portofino, Chrome c. 0002-52110-0002 Bracket, Mounting, Potofino, Chrome d. 0002-51500-0000 Anchor, Drywall, #6 e. 0002-50200-0000 Screw, 50mm, 6,coarse thread f. 0002-52200-0000 Screw, machine, 30mm, 5 g. 0002-52200-0001 Screw, machine, 20mm, 5 h.
Bracket Assembly Instructions - Portofino Step 1 Measure for position of brackets using the template if desired. At least two brackets must attach to a stud. Step 2 Affix part C to the wall using screw e and drywall anchor d* where necessary.** Slot in C should face downwards. Repeat Step 2 for the three remaining brackets. Step 3 Insert rubber pads h (2x) into A and B. Clamp A and B around the Towel Warmer horizontal bar with A on the top. Insert screw g and tighten.
Bracket Assembly Diagrams - Riviera A B G 1x 4x H 4x 2x c d e* f 4x 4x A c 8x 1x f B Riviera a. 0002-51110-0000 Bracket, mounting, stainless steel, Riviera b. 0002-51310-0000 Stud, threaded, mounting, stainless steel c. 0002-50210-0000 Screw, set, 3mm d. 0002-50900-0000 Wrench, hex key, 3mm e. 0002-50500-0000 Anchor, drywall, gray, #8 f. 0002-50200-0000 Screw, 50mm x 8 g. 0002-50710-0000 Cap, vented (not shown) h.
Bracket Assembly Instructions - Riviera Step 1 Measure for position of brackets using the template if desired. At least two brackets must attach to a stud. Step 2 Affix part A to the wall using screw f and drywall anchor e* where necessary.** Repeat Step 2 for the three remaining brackets. Step 3 Screw part B into the positions on the Towel Warmer. Repeat Step 3 for the three remaining brackets.
Diagram A. Diagram B. Label O-ring Diagram C. Step 9 With the brackets now in place, slide electrical wires through rubber O-ring on electrical plate. Refer to Diagram A. Do not remove rubber o-ring from electrical plate under any circumstances. Step 10 Adjust the Towel Warmer to desired position from wall and screw the screws into place, but do not tighten at this time.
Final Installation Instructions (for all models) - cont’d Step 11 Have a certified professional wire the Towel Warmer to the electrical line according to code, referring to the detailed wiring diagram provided in Appendix B. Step 12 Push the wires into the electrical box and screw the cover plate to the outside of the box. Step 13 Screw the adjustable collar out and tighten it against the faceplate on the electrical box, ensuring the rubber seal is in position and sealed correctly inside the collar.
OPERATION WarmlyYours Towel Warmers include our programmable timer for luxurious and economical use of the Towel Warmer. On Towel Warmer runs at 100% power and will reach temperatures between 100˚ F and 140˚ F depending on the following: running time, number of towels, type of towels and ambient room temperature. Automatic Mode Programmable Timer allows up to 14 events or 2 ON-OFF cycles per day. Easy programming allows you to set intervals of operation for each day of the week.
Product Construction - Towel Warmer Depending on the model, the towel warmer is constructed from high carbon steel or stainless steel with a wall thickness of between 0.8 mm and 1.2 mm. The steel tubing is brazed together with full, continuous joints. The finished assembly is electroplated, polished, or brushed, depending on the model and style. The towel warmer is heated with a heating element. The mounting brackets are manufactured from steel and finished to match the finish of the specific model.
WarmlyYours Towel Warmer Warranty WarmlyYours.com Inc. warrants the WarmlyYours Towel Warmers (“the Product”) to be free from defects in materials and workmanship for five years from the date of sale, provided that the Product is installed in accordance with the accompanying Installation and Operation Manual, and any special written design or installation guidelines provided by WarmlyYours.com Inc. for this product, the National Electric Code (NEC), and all applicable local building and electrical codes.
Appendix A1: Rough-In Diagram - Riviera Note: Dimensions shown are distances between the center of anchor points. This example shows 16” on center construction. Your situation may vary depending on your stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
Appendix A2: Rough-In Diagram - Portofino Note: Dimensions shown are distances between the center of anchor points. This example shows 16” on center construction. Your situation may vary depending on your stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
Appendix B: Wiring Diagram (All models) 2” x 4” ELECTRICAL BOX FOR TIMER 120 Volt TIMER LINE (black) 120 a.c.
