Hardwired Model Shown Installation & Operation Manual for WarmlyYours Infinity Towel Warmers
Thank you for choosing a finely crafted WarmlyYours Infinity towel warmer. The Infinity’s radiant heat gently warms your towel or bathrobe, allowing you to wrap yourself in luxurious comfort as you step out of the bath or shower. Included in this document are all necessary installation and operating instructions. To locate the model number, refer to the product label as shown in Diagram D on page 8.
1. Affixing the Towel Warmer to the Wall Step 1 Draw a diagram of the preferred location of the brackets and the electrical connection on the towel warmer box to create a template (see Step 2 for template instructions). At least two of the four brackets must be attached directly to a stud. The Infinity Plug-In model must be installed less than 6 feet (183cm) from a properly grounded outlet to ensure the plug can reach.
1. Affixing the Towel Warmer to the Wall (continued) Note: Dimensions shown are distances between the center of anchor points. This example shows 16 inches on center construction. Your situation may vary depending on stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
1. Affixing the Towel Warmer to the Wall (continued) Diagram B: Rough-In Diagram Note: Dimensions shown are distances between the center of anchor points. This example shows 16 inches on center construction. Your situation may vary depending on stud spacing. WARNING: Locations of electrical box and anchor points may vary. Measure all dimensions prior to rough-in and installation.
2.
2. Bracket Assembly Instructions (continued) BB C C CCC Infinity TW-F10BS-HW Parts List B A A C B B B A C C fg e hg fh C A g g g de dd d ef ee e gf f f hfg gghg hh h d d e C B BBB f h h PART # i d C C de j ef d g h h QTY A. 0005-57110-0001 DESCRIPTION 4 Bracket, mounting, stainless steel 4 Tube assy., mounting, stainless steel 4 Screw, tube mounting, 8mm x 70mm d. 0005-57900-0001 1 Wrench, hex key, 8mm e. 0005-57900-0002 1 Wrench, hex key, 6mm f.
2. Bracket Assembly Instructions (continued) Step 1 Measure for bracket positions using the template if desired. At least two brackets must be attached to a stud. Step 2 Affix brackets A to the wall using screw g and drywall anchor f where necessary. Repeat Step 2 for the three remaining brackets. Step 3 Place and orient the curved end of tubing B with the threaded inserts located at four points on the back of the towel warmer.
2. Bracket Assembly Instructions (continued) Step 8 Hardwired Model Only (continued) Ensure the rubber seal is in position and sealed correctly inside the collar. Refer to Diagram E. Slide the brushed stainless collar over the tube until it is touching the face of the O-ring on the cover plate. Hardwired Model Skip Steps 9-10. Plug-In Model Only Plug the cord into a properly grounded outlet. Do NOT use an extension cord to make the connection between the towel warmer plug and outlet.
3.
4. OPERATION Plug-In Model With your Infinity Plug-In model secured to the wall and plugged into a grounded outlet, you are now ready to enjoy your towel warmer. Use the ON/ OFF switch located on the bottom left side (when facing the towel warmer) to control when you want the unit to warm. Refer to Diagram D for switch for location. Hardwired Model WarmlyYours towel warmers include our programmable timer for luxurious and economical use of the towel warmer.
5. SPECIFICATIONS Item # Model Dimensions Volts Watts Ohms Amps TW-F10BS-HW Hardwired W: 3 5/8” (600mm) H : 32” (811mm) D: 4 ¾” (121mm) 120 150 95 1.25 TW-F10BS-PL Plug-In W: 23 5/8” (600mm) H: 32” (811mm) D: 4 ¾” (121mm) 120 150 95 1.25 Product Construction - Infinity Towel Warmer The Infinity Towel Warmers are constructed from Type 304 stainless steel and have a brushed finish. The stainless steel tubing is pre-assembled and tack-welded together for rigidity.
6. WarmlyYours Towel Warmer Warranty WarmlyYours.com Inc. warrants the WarmlyYours towel warmers (“the Product”) to be free from defects in materials and workmanship for two years from the date of sale, provided that the Product is installed in accordance with the accompanying Installation and Operation Manual and any special written design or installation guidelines provided by WarmlyYours.com Inc.
