Installation & Operation Manual for WarmlyYours Towel Warmers
Thank you for choosing a finely crafted Towel Warmer from the Elements™ Collection by WarmlyYours. Now you can enjoy the luxury of a warm towel everyday. These models are so easy to install and use. Just plug the Towel Warmer unit into a standard 120V outlet, pre-heat your towel warmer and enjoy a warm, dry towel or bathrobe upon stepping from the shower. All of the necessary installation and operation instructions are included in this manual.
INSTALLATION This appliance must be installed in accordance with the instructions in the manual and the NEC guidelines relating to electrical fixtures in bathrooms. We recommend that the Towel Warmer be plugged into a GFCI protected circuit. Install the Towel Warmer as close to an electrical outlet as possible. If an extension cord becomes necessary, always use a grounded 3-wire extension cord. Confirm that the cord’s electrical rating is at least as high as the electrical rating of the Towel Warmer.
Affixing the Towel Warmer to the Wall NOTE: Install the Towel Warmer no less than 1 foot from the floor and near an electrical outlet. The electrical outlet must be properly grounded. Position the brackets on the Towel Warmer to ensure that the Towel Warmer is firmly affixed to the wall. See pages 8,9 and 10 for for bracket assembly and installation recommendations.
Step 6 With the brackets now in place, adjust the Towel Warmer to desired position and fully tighten the screws into place. Step 7 Plug the Towel Warmer into a GFCI 120V, 15A electrical outlet.
Affixing the Towel Warmer to the Wall - cont’d WARNING Measure all dimensions prior to rough-in and installation. Elements™ model: TW-E2CP Stud 14” (356mm) Recommended† Anchor Points* Anchor Points 2” (51mm) 24 1/2” (622mm) Anchor Points* * Note: Anchor points must be attached to a stud. † Note: Drywall mounted bracket location is recommended, but can move up to 2” (51mm) horizontally as desired.
Affixing the Towel Warmer to the Wall - cont’d WARNING Measure all dimensions prior to rough-in and installation. Elements™ model: TW-E3CP 11” (279mm) Recommended† Stud Anchor Points* Anchor Points 2” (51mm) 24 7/8” (632mm) Anchor Points* * Note: Anchor points must be attached to a stud. † Note: Drywall mounted bracket location is recommended, but can move up to 2” (51mm) horizontally as desired.
Affixing the Towel Warmer to the Wall - cont’d WARNING Measure all dimensions prior to rough-in and installation. Elements™ model: TW-E4PCP Stud Anchor Points* 12” (305mm) Recommended† Anchor Points* 2” (51mm) Pin Hole 8 7/8” (200mm) * Note: Anchor points must be attached to a stud. † Note: 12” between brackets is recommended, but the top bracket can move up to 2” vertically as desired.
Bracket Assembly and Installation Diagrams WARNING Measure all dimensions prior to rough-in and installation. Elements™ model: TW-E2CP Do NOT use Drywall Anchors on stud Stud Drywall Anchors Quantity 6 Brackets Quantity 3 Install this bracket with holder side facing downward.
Bracket Assembly and Installation Diagrams - cont’d WARNING Measure all dimensions prior to rough-in and installation. Elements™ model: TW-E3CP Do NOT use Drywall Anchors on stud Stud Drywall Anchors Quantity 6 Brackets Quantity 3 Screws Quantity 6 Install this bracket with holder side facing downward.
Bracket Assembly and Installation Diagrams - cont’d WARNING Measure all dimensions prior to rough-in and installation.
Bracket Assembly and Installation Diagrams OPERATION All models of the Elements™ Towel Warmer Collection include an easy and accessible “on/off” button. Turn the power “on” by pressing the red “on/off” button located on the unit. Refer to Diagram A. The “on” setting is indicated by an “I” and the “off” setting is indicated by “O.” A light will illuminate when the button is switched to the “on” position. In approximately 10-15 minutes, your Towel Warmer will be warm to the touch.
SPECIFICATIONS TW-E2CP Elements™ 23.6”W x 25.6’H x 3.5”D 120 60 240 0.50 TW-E3CP Elements™ 19.7”Wx25.6”Hx 3.5”D 120 60 240 0.50 TW-E4PCP Elements™ 16.3”Wx28.5”Hx3.5”D 120 60 240 0.50 Product Construction - Towel Warmer The Towel Warmer is constructed with continuous 1” heavy gauge SPHC steel tubing. The finished assembly is chrome plated and is heated by a UL listed wire which is designed for rapid and safe heating.
SAFETY GUIDELINES The main electrical line feeding the Towel Warmer must incorporate a Ground Fault Circuit Interrupter (GFCI) for North America. WarmlyYours - Elements Towel Warmer Warranty WarmlyYours.com Inc.
WARMLYYOURS.COM INC. FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WARMLYYOURS.COM INC. HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
