Installation Guide

ManualsBrandsWarmlyYours ManualsBathElevate Grande 10-Bar Electric Towel Warmer in Polished Stainless Steel

TOOLS REQUIRED ACCESSORIES FOR SQUARE/ROUND MOUNTING TUBES

INSTRUCTIONS

Before using this product, please read the following instructions carefully and keep this

pamphlet for future reference.

ABOUT THE PRODUCT:

This heated towel warmer is designed for drying/warming towels or clothes, it has a surface

stabilized temperature of 122-131ºF, and it is used in household bathrooms and kitchens, as

well as in hotels and restaurants or other public areas. This appliance uses a voltage of 120

VAC, and is manufactured according to cULus standards.

SAFETY PRECAUTIONS:

1. The towel warmer must be used with a Ground Fault Circuit Intercepter (GFCI) circuit.

2. This product is supplied with a three-prong plug or three-wire cable.

To avoid unnecessary risk or danger, this product must be properly grounded.

3. Any repairs must be done by a qualified technician who is deemed qualified by industry

standards. When any external wire fittings are required, the unit must be disconnected

from the circuit.

WARNING:

1. Only use for drying textiles which have been dampened by water.

2. If heating wire is damaged, the whole product should be replaced.

NOTE:

1. In the event of any difference in technical specifications, please refer to the actual product.

2. Please wipe the towel rail with a soft, dry cloth when cleaning it.

Do not use scrubbers or abrasive cleaners.

INSTALLATION GUIDE

For TWS6 Series hardwired towel warmers

Installation Support •(800) 875-5285 • WarmlyYours

1+2

Installation Fittings:

(1+2): Mounting tubes (4 pieces) & Set screws (4 pieces)

(3) 4 brackets (4 pieces)

(4) Short mounting screws (3 pieces), Long mounting screw (1 piece)

(5) Drywall anchor (4 pieces)

(6) Long screws (4 pieces)

This product must be installed in accordance with the instructions in

the manual and the NEC and CEC guidelines relating to electrical

fixtures in bathrooms. The Towel Warmer must be on a GFCI

protected circuit and be wired by a professional who is certified

to do electrical wiring.

In order to reduce electrical shock, this towel warmer should be

installed on a 15A GFCI protected branch circuit (14AWG) and to an

outlet box that is 4 inches (10.16 cm) high by 2 Inches

(5.08 cm) wide.

Summary of content (4 pages)

PAGE 1
INSTALLATION GUIDE For TWS6 Series hardwired towel warmers TOOLS REQUIRED ACCESSORIES FOR SQUARE/ROUND MOUNTING TUBES 1+2 1+2 INSTRUCTIONS Before using this product, please read the following instructions carefully and keep this pamphlet for future reference.
PAGE 2
INSTALLATION GUIDE For TWS6 Series hardwired towel warmers ACCESSORIES a 3 PCS h b 1 PCS i c 4 PCS 3 PCS e 1 PCS f g 4 PCS j d 4 PCS k STEP 1 1 PCS 1 PCS a STEP 2 4 PCS L 1 PCS STEP 1: As shown in the picture, insert the short mounting screw (d) through the tube in the center of the mounting tube (a). c STEP 2: Use the short mounting screw (d) to fix the mounting tube (a) to the threaded metal pad on the vertical bar on the back of the towel warmer.
PAGE 3
INSTALLATION GUIDE For TWS6 Series hardwired towel warmers STEP 5 A B C STEP 6 STEP 5: Use a tape measure to measure the distance STEP 8 STEP 8: Use a hammer to knock plastic drywall anchor (f) into wall completely. STEP 9 STEP 9: Insert long screw (i) through mounting bracket (g), then screw into plastic drywall anchor (f). STEP 10 STEP 10: Install the tube (a) onto the bracket (g).
PAGE 4
INSTALLATION GUIDE For TWS6 Series hardwired towel warmers ELECTRICAL ASSEMBLY (j) (L) (k) (b) Junction box for optional control. (c) Grounding wire fixed to the junction box cover plate by ground screw. HOT LOAD (black or blue) NEUTRAL LOAD (white or brown) GROUND (green/yellow) 2” x 4” ELECTRICAL BOX SWITCH CAUTION： To provide continued protection against risk of electric shock, connect to properly grounded outlets only.