Product Manual

ManualsBrandsWARN ManualsFairleadsRoller Winch Fairlead

Page 1 64951 B1

INSTALLATION INSTRUCTIONS

WARN Works

Fairlead P/N 64952 or 71294

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided

installation and operating instructions and other information on labels and in this guide. This information alerts you to potential

hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you

must use your own good judgment.

CARELESS WINCH INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE.

READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND

OPERATING THIS PRODUCT.

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death.

WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:

WARNING signals a hazard that

could

cause serious injury or death, if you do not follow recommendations.

CAUTION signals a hazard that

may

cause minor to moderate injury, if you do not follow recommendations.

This guide uses

NOTICE

to call attention to important mechanical information, and Note: to emphasize general information worthy

of special attention

Installation Instructions

1. Install winch fairlead to front of mounting plate (See Figure 1 ). Orient roller fairlead with roller bolt

heads facing down for flush mounting. Use hardware included with fairlead or 2 each of the following:

3/8-16x ¾ inch cap screw (Grade 5 or better), 3/8-16 hex nut, and 3/8 lock washer. Torque bolts to

30-35 ft-lbs (41-47 Nm).

2. For applications without pre-drilled holes, drill the appropriate hole patern to mount the fairlead:

P/N 64952 (3”) - 2 holes, 7/16” inch (11.1 mm) diameter on a 4 ⅞ inch (12.42 cm) center.

P/N 71294 (4 ½ “) - 2 holes, 7/16” inch (11.1 mm) diameter on a 6 inch (15.24 cm) center.

3. For the 4700 winch, unbolt the lower roller on the fairlead. Pull the bolt out and let the roller drop.

Thread wire rope loop through opening. Re-install bolt. Torque bolt to 30-35 ft-lbs (41-47 Nm).

CAUTION

CAUTIONCAUTION

CAUTION

DRILL DEBRIS HAZARD

Failure to observe these instructions could lead to minor to moderate injury.

• Always wear SAFETY GOGGLES when using drill. Drilling can produce flying metal chips and cause eye injury.

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS WARN WorksTM Fairlead P/N 64952 or 71294 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided installation and operating instructions and other information on labels and in this guide. This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
PAGE 2
WARNING MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to severe injury or death. To avoid injury to hands or fingers. • Always keep hands clear of wire rope, hook loop, hook and fairlead opening during installation, operation and when spooling in or out. • Always use extreme caution when handling hook and wire rope during spooling operations.
PAGE 3
INSTRUCTIONS D’INSTALLATION Guide-câble WARN WorksTM Réf. 64952 ou 71294 Votre sécurité et celle des autres sont très importantes. Afin de vous permettre de prendre des décisions éclairées dans le domaine de la sécurité, nous vous fournissons des instructions relatives à l'installation et à l'utilisation du produit ainsi que d'autres informations figurant sur des étiquettes et dans ce guide. Ces informations attirent l'attention sur les dangers potentiels pouvant affecter l’opérateur et des tiers.
PAGE 4
AVERTISSEMENT DANGER DE HAPPEMENT PAR DES PIÈCES MOBILES Le non-respect des consignes peut entraîner des blessures graves, voire mortelles. Pour éviter de se blesser les mains ou les doigts. • Toujours garder les mains éloignées du câble, de la boucle du crochet, du crochet et de l'ouverture du guide-câble durant l'installation et l’utilisation du treuil et l'enroulement ou le déroulement du câble.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN WARN WorksTM Guía, Nº de ref. 64952 o 71294 Su seguridad y la seguridad de los demás son muy importantes. Para ayudarle a tomar decisiones informadas sobre seguridad, se proporcionan instrucciones de instalación y funcionamiento, así como otra información en etiquetas y en esta guía. Esta información le alerta sobre posibles peligros que puedan afectarle a usted y a otros.
PAGE 6
ADVERTENCIA PELIGRO DE ENREDO EN LAS PARTES MÓVILES Si no se observan estas instrucciones, podrían producirse lesiones graves e, incluso, la muerte. Para evitar daños en las manos: • Mantenga siempre las manos alejadas del cable, del bucle del gancho, del gancho y de la abertura de la guía durante la instalación, el funcionamiento y en el enrollado y desenrollado. • Proceda siempre con extremo cuidado al manejar el gancho y el cable durante las operaciones de enrollado y desenrollado.