WatchGuard V10, V60L, V60, V80, V100 Hardware Guide ® Vclass 5.
FCC Certification This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
VCCI Notice Class A ITE Firebox V10, V60L, V60, V80, V100 Hardware Guide iii
Declaration of Conformity iv Vclass
Firebox Limited Hardware Warranty This Limited Hardware Warranty (the “Warranty”) applies to the enclosed WatchGuard hardware product (the “Product”), not including any associated software which is licensed pursuant to a seperate end-user license agreement and warranty. BY USING THE PRODUCT, YOU AGREE TO THE TERMS HEREOF. If you do not agree to these terms, please return this package, along with proof of purchase, to the authorized dealer from which you purchased it for a full refund.
YOU OR ANY THIRD PARTY (WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE OR IMPUTED NEGLIGENCE AND STRICT LIABILITY AND FAULT) OR OTHER THEORY) FOR COST OF COVER OR FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION LOSS OF PROFITS, BUSINESS, OR DATA) ARISING OUT OF OR IN CONNECTION WITH THIS WARRANTY OR THE USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF WATCHGUARD TECHNOLOGIES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
RC2 Symmetric Block Cipher, RC4 Symmetric Stream Cipher, RC5 Symmetric Block Cipher, BSAFE, TIPEM, RSA Public Key Cryptosystem, MD, MD2, MD4, and MD5 are either trademarks or registered trademarks of RSA Data Security, Inc. Certain materials herein are Copyright © 1992-1999 RSA Data Security, Inc. All rights reserved. RealNetworks, RealAudio, and RealVideo are either a registered trademark or trademark of RealNetworks, Inc. in the United States and/or other countries.
textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2.
Contents CHAPTER 1 Hardware Descriptions ..............................1 Package Contents ............................................................ 1 WatchGuard Firebox V10 security appliance ....................... 1 WatchGuard Firebox V60, V60L, and V80 security appliance ..2 WatchGuard Firebox V100 security appliance .....................2 ....................................................... 3 The Firebox V10 model ..................................................
x Vclass
Hardware Descriptions CHAPTER 1 This chapter provides a visual tour of the external hardware features of the WatchGuard® Firebox® V10, V60, V80, and V100 security appliances, focusing on the buttons, LEDs, interfaces, ports. Please see the Firebox Vclass User Guide for installation instructions. Package Contents Each appliance model is packaged with different contents, as described in this section. WatchGuard Firebox V10 security appliance • • • One 12V 1.
CHAPTER 1: Hardware Descriptions and Linux. The CD also provides electronic versions of the complete user documentation set.
Front and Back Views • operating systems: Windows 2000/XP, Solaris, and Linux. The CD also provides electronic versions of the complete user documentation set. Rack-mounting hardware. If you are mounting the appliance in a rack, note that the Firebox V100 is 1 U high. Front and Back Views The Firebox V10 model The front panel of a Firebox V10 appliance contains the indicators shown in the following illustration.
CHAPTER 1: Hardware Descriptions Alarm Illuminates when certain alarms are triggered. For more information on alarms, see the Firebox Vclass User Guide. Admin Illuminates when a system administrator is connected to the appliance by means of the Vcontroller or the WatchGuard CLI. The back panel of a Firebox V10 appliance contains the interfaces and ports shown in the following illustration.
Front and Back Views Power Port This interface serves as the connection to a 100VAC-to-240VAC (50/60Hz) source. Use the power cord supplied in the package to connect this appliance to a UPS device or to a power outlet. The power supply can auto-detect 110/220 voltage. NOTE Always connect the power cable to the power port on the back of the V10 before you connect it to the AC outlet.
CHAPTER 1: Hardware Descriptions lights labeled 10 and 100. These LEDs indicate the speed of traffic being transmitted. High Availability Status LED Indicates the current status of this appliance, if it is one of two connected as a high-availability system. If this is the primary appliance, and the light is on and steady, the system is functional, and this appliance is on-line. If this is the primary appliance and the LED is blinking, a failover has occurred and the secondary appliance is online.
Front and Back Views Alarm Illuminates when certain alarms are triggered. For more information on alarms, see the Firebox Vclass User Guide. Reset port This opening allows you to insert a straight pin or paperclip and press an internal reset switch that restarts the appliance. Power LED Illuminates when the appliance has been turned on. The back panel of a Firebox V60, V60L, or V80 contains the features shown in the following illustration.
CHAPTER 1: Hardware Descriptions appliance if the power goes out, prompting the appliance to shut itself down properly. UPS devices from American Power Company (APC) are currently supported by the Firebox Vclass power management firmware. Check the WatchGuard Web site (www.watchguard.com) for updated information on complete UPS support.
Front and Back Views passes. These interfaces are multi-mode, but they do not support 10/100 communications. On each side of the two Gigabit interfaces are three LEDs labeled RX, TX, and Link. The Link LED is lit when a connection is active. The RX LED blinks steadily when data packets are being received by the appliance. The TX LED blinks steadily when data packets are being transmitted.
CHAPTER 1: Hardware Descriptions Ready Blinks when the appliance is powering up or powering down. It is steadily lit when the appliance is ready for network traffic. Admin Illuminates when a user or system administrator is connected to the Firebox Vclass appliance by means of the Vcontroller or the WatchGuard CLI. Alarm Indicates when an alarm is activated. For more information on alarms, see the Firebox Vclass User Guide.
Firebox V10, V60, V60L, V80, and V100 Components AC Power Cord Enables you to connect the appliance (using the supplied power cord) to a 100 to 240VAC (50/ 60Hz) power source. The power supply can autodetect 110/220 voltage. Power Supply Switch Allows you to turn the appliance on or off. UPS Port Allows you to use the RS-232 cable provided in the package to connect the appliance to an Uninterruptable Power Supply (UPS).
CHAPTER 1: Hardware Descriptions primary duties: protecting your network and efficiently managing all legitimate data streams. WatchGuard Firebox Vclass Operating System™ (OS) Every Firebox Vclass security appliance is preinstalled with the latest version of the Firebox Vclass Operating System–which is identified on the packaging by a version number. This operating system includes all the software resources that make the appliance fully functional.
Index A AC power 7, 11 Admin LED 4, 6, 10 Alarm LED 4, 7, 10 C L LEDs Admin 4, 6, 10 Alarm 4, 7, 10 HA status 6, 9 Power 3, 7, 10 Ready 3, 6, 10 P certification, FCC ii Console interface 4, 6, 9 power failures 5 power interface 5 Power LED 3, 7, 10 Power switch 7, 11 E R Ethernet interfaces for Firebox V10 4 for Firebox V100 8 for Firebox V60 and V80 5 RapidCore hardware ensemble 11 Ready LED 3, 6, 10 Reset switch 7, 10 F FCC certification ii Firebox V10 back panel 4 front panel 3 package contents