Product Info
Table Of Contents
- Important Notice
- Introduction
- Using the V300
- Using WatchGuard V300 Camera
- Basic workflow
- Wearing WatchGuard V300 Camera
- V300 Camera Field Of View
- Power On and Off
- Starting and Stopping a Recorded Event
- Categorizing a Recorded Event
- Momentary Muting of the Audio
- Docking the WatchGuard V300 Camera overview
- Docking the V300 Camera in a Transfer Station
- Docking and UnDocking the V300 Camera in a USB base
- Uploading events
- About the V300 Camera
- V300 Special Features
- Using V300 with a recording group
- V300 Transfer Station
- Internal Only - debug
FCC and ICnotices
This equipment complies with Part 15 of the FCC rules and Industry Canada licence-exempt RSS standard(s).
This equipment should only be used with the antenna supplied by WatchGuard Video. Any changes or
modifications not expressly approved by the manufacturer could void the user's authority to operate the
equipment.
WatchGuard V300 contains the following IDs:
FCC ID: YJV-VST400
IC: 9073A-VST-400
WatchGuard WiFi base contains the following IDs:
FCC ID: YJV-VST500
IC: 9073A-VST500
Cet appareil est conforme à la Partie 15 des règlements de la FCC et Industrie Canada exempts de licence
standard RSS. Cet appareil doit être utilisé uniquement avec l'antenne fournie par WatchGuard Video. Tout
changement ou modification non expressément approuvée par le fabricant pourrait annuler l'autorité de
l'utilisateur de faire fonctionner l'appareil.
WatchGuard V300 contient les identifiants suivants:
FCC ID: YJV-VST400
IC: 9073A-VST400
WatchGuard WiFi Base contient les identifiants suivants:
FCC ID: YJV-VST500
IC: 9073A-VST500
The device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s) subject
to the following two conditions:
1.
The device may not cause harmful interference.
2.
The device must accept all interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à la Partie 15 des règlements de la FCC et Industrie Canada exempts de licence
standard RSS soumis aux deux conditions suivantes:
1.
Cet appareil ne peut causer des interférences nuisibles.
2.
Cet appareil doit accepter toutes les interférences reçues, y compris les interférences qui peuvent
perturber le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, cet émetteur radio ne peut fonctionner à l'aide d'une
antenne d'un type et maximum (ou moins) Gain approuvé pour l'émetteur par Industrie Canada. Pour réduire le
risque d'interférence avec d'autres utilisateurs, le type d'antenne et son gain doivent être choisis afin que la
puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication
réussie.
The radio transmitters IC: 9073A-5 have been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for
that type, are strictly prohibited for use with this device.
Antenna type (radio transmitter): WatchGuard part number WGP02541, 4.6 dbi gain, 50 Ohm impedance.
Ces émetteurs radios IC: 9073A-VST500 ont été approuvés par “Industry Canada” pour fonctionner avec les
types d'antennes énumérés ci-dessous avec le gain maximal admissible et l'impédance d'antenne requise pour
WGD00169
Revision Revision A (Draft)
iv