Use and Care Manual

ManualsBrandsWatco ManualsOther1 qt. Greystone Teak Oil (4-Pack)

TECHNICAL DATA

WAT-21

WATCO

TEAL OIL + STAIN

Form: ARJ-1997

Rev.: 060420

DESCRIPTION AND USES

Watco

Teak Oil + Stain is specifically formulated for dense

woods such as teak, mahogany and rosewood. Watco Teak

Oil + Stain penetrates deep into wood pores to create the rich,

warm glow of a hand-rubbed finish. Watco Teak Oil + Stain

protects wood from within. It will not chip, peel or wear away.

Use to treat outdoor or indoor furniture and on marine surfaces

such as wood boat decks, cabinets and rails. It is not

recommended for patio decks, below waterline wood surfaces

or interior floors. Teak Oil + Stain is easy to use. Simply brush

or wipe on and wipe off.

PRODUCT FEATURES

 Excellent protection for dense woods

 Penetrates and protects

 Easy application & maintenance

PRODUCTS

SKU

DESCRIPTION (Quart)

348746

Hazelnut 350

348759

Greystone 350

348747

Jacobean 350

348758

Flagstone 350

PRODUCT APPLICATION

SURFACE PREPARATION

Ensure the wood is dry and free from subsurface moisture

and that all surface coatings such as paint or varnish are

completely removed. Sand if a smooth finish is desired.

WARNING: If you scrape, sand, or remove old paint, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN

DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT

WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a

NIOSH-approved respirator to control lead exposure. Clean up

carefully with a HEPA vacuum and a wet mop. Before you

start, find out how to protect yourself and your family by

contacting the National Lead Information Hotline at 1-800-424-

LEAD or log on to www.eps.gov/lead.

PRODUCT APPLICATION (cont.)

APPLICATION

DO NOT APPLY IN WET WEATHER OR WHEN AIR AND

SURFACE TEMPERATURES ARE BELOW 50°F OR

ABOVE 95°F. Watco Teak Oil Finish may appear milky in the

can but will dry to a clear film.

SHAKE CONTAINER THOROUGHLY and test for color on a

hidden section of wood. Flood the surface with a heavy

application of Watco Teak Oil + Stain with a brush, cloth,

roller or spray, applying additional finish to areas that absorb

all the liquid. Allow the oil to penetrate for 30 minutes. (Avoid

spilling on fiberglass portions of a boat. Wipe immediately

and remove using a rubbing compound). Re-apply allowing

an additional 15 minutes penetration. Wipe the surface

completely dry. The surface is ready for use in 8-10 hours.

If a topcoat such as a polyurethane is desired, allow Watco

Teak Oil + Stain to dry 72 hours before application of the

polyurethane.

MAINTENANCE

Periodically re-apply Watco Teak Oil + Stain Finish to wood

that appears dry to enhance to beauty and look of the finish.

CLEAN UP

Clean application tools and equipment with mineral spirits or

paint thinner.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA WAT-21 WATCO® TEAL OIL + STAIN DESCRIPTION AND USES PRODUCT APPLICATION (cont.) Watco® APPLICATION Teak Oil + Stain is specifically formulated for dense woods such as teak, mahogany and rosewood. Watco Teak Oil + Stain penetrates deep into wood pores to create the rich, warm glow of a hand-rubbed finish. Watco Teak Oil + Stain protects wood from within. It will not chip, peel or wear away. DO NOT APPLY IN WET WEATHER OR WHEN AIR AND SURFACE TEMPERATURES ARE BELOW 50°F OR ABOVE 95°F.
PAGE 2
TECHNICAL DATA WAT-21 WATCO® TEAL OIL + STAIN PHYSICAL PROPERTIES TEAK OIL + STAIN Resin Type Raw Linseed Oil and Hydrocarbon Resin Pigment Type Inorganic Solvents Mineral Spirits, Light Aromatic Naphtha Per Gallon 7.60-8.05 lbs. Per Liter 0.91-0.96 kg Weight By Weight 62-63% By Volume 55-57% Solids Volatile Organic Compounds <350 g/l (2.87 lbs./gal.