Thanks for your purchase from water drop. We value your patronage and appreciate your confidence in us. Counting vou among our customers is something for which we are especially grateful. Please let us know If we can do anything else to help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any Interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the parky responsible for compliance could void the user's authority to operate the equipment.
Contents Installation Instructions Before Installation Parts list Product Introduction... installation Tips Installation Steps. Step 1: Install the Feed Water Adapter. Step 2: Install the RO Faucet and UV Sterilizer. Step 3: Install the Drain Saddle Step 4: Position the RO system Housing . Step 5: Connect Tubing Step 6: Connect Power Cord Step 7: Install the Filters Step 8: Startup the System 11 © woe ND ow ER Owner's Manual Display and Operation 13 Section 1: TDS Display. Section 2: UV Sterilizer Display.
Installation Instructions Before Installation Inspect the Package Pen the box and take out the system housing, all the components and connect fittings. Inspect them according to the parts list to ensure nothing is sift out or damaged during shipping. If there are any parts cracked or broken, please do not proceed with the installation and contact us to identify and get familiar with al! components for quick installation.
a no Activated carbon Filter P re-gediment and Revers Osmosis sermons “ios CEE WWW RO Faucet UV Sterilizer Fed Water Adapter White 3/8" PE Tubing Lock Clip Teflon Tape X1 Set X18et 1st Preinstalled Drain Saddle 1/4 White 1/4" PE Tubing Red 1/4" PE Tubing Power Adapter X18 Set
Product Introduction The brief introduction of various parts and sample connections are presented as follows. Please identify and get familiar with these parts and connection points for a smooth installation.
Installation Tips How to Use the Quick-Connect Fittings Sari for “Full Insert ia Figure 1 To connect: NOTE: There Is an existing mark (Figure 1} at the end of the tubing for you to confirm If the tubing Is fully Inserted into the fitting. = Push the tubing Into the fitting until you reach the mark on the tubing. MOTE: If the tubing is not fully inserted, no seal will be created and leakage will our « When the tubing is fully inserted, put the blue lock clip on the fitting.
How to Drill a Hole into Your Sink or Counter top {Optional} NOTE: Please confirm if there is an existing hole available to install the RO faucet. if not, please drill a hole in accordance with the following steps. it's highly recommended fo watch the YouTube video “How to Drill Faucet Holes” for a better understanding of the process. There is also a reference sticker to help you drill the hole. Remember to wear safety glasses to protect your eyes while drilling the faucet hole. 1.
Found Water Adapter 38" INPUT Water Cold Water = Supply Valve Figure 4 Unscrew | ™ 4 Unscrew Figure § Step 2: Install the RO Faucet and UV Sterilizer (Non-Air Gap Faucet) NOTE: If your kitchen sink or counter top does not have an existing hole, you will have to drill one (17). Refer to Page 5. 1. Insert the faucet spout into the faucet body; 2. Insert the faucet stem and power cord into the hole on the counter top; 3.
Step 3: install the Drain Saddle 1. Choose a spot on the drainpipe that is convenient for installing the drain saddle; NOTE: It's recommended to install the drain saddle on the vertical drainpipe. 2. Drill a 1/4” hole in the drainpipe. Be sure not to penetrate the opposite side of the pipe; 3. Slip the front plate on one end of the tubing (without the mark}, and insert the tubing into the drilled hole for about 0.8" (Figure 8); 4.
Step 5: Connect Tubing NOTE: Confirm the tubing length you need first, and then cut the tubing if it's too long, referring to “How to Use the Quick-Connect Fittings” on page 4. 1. Install the “INPUT” Water Tubing » Remove the plug from “INPUT” water port; « {identify the white 3/8” PE tubing which has been attached to the feed water adapter (Figure 11); « insert the other end of the {fusing into the “INPUT” water port {Figure 12), and pop the lock clip on the fitting.
3. Install the “WASTE” Water Tubing « Remove the plug from the “WASTE” water port; » identify the red 1/4" PE tubing which has been attached fo the drain saddle (Figure 18); =» insert the other end of the tubing into the “WASTE” water port (Figure 18), and pop the lock clip onto the fitting. NOTE: Make sure it is fully inserted until you reach the mark on the tubing. “WASTE” Water Tubing Figure 15 Figure 16 Step 6: Connect Power Cord 1.
Step 7: install the Filters Each filter is marked with a logo (CB/CF/RO) and an installation arrow. 1. Remove the wrapping and protective cap from the filter; 2. Insert the filter info its corresponding hole (Figure 19), align the arrow with the empty circle on the housing (Figure 20); 3. Twist the filter with a lite force forward in a clockwise direction for 80 degrees, until the arrow is aligned with the solid circle on the housing (Figure 21).
4. Tum on the RO faucet, and allow it fo run for 30 minutes until the front panel screen starts displaying a TDS reading (Figure 23); NOTE: Be sure to carefully check the tightness of each part of the system while flushing. Check and ensure all tubing Is Installed comely and completely. Make sure there are no leaks al the joints, fittings, valves and tubing connections. NOTE: The water is not drinkable during the flushing. The 30 minutes are accumulative.
Owner's Manual Display and Operation Section 1: TDS Display The built-in TDS sensor detects the water quality when the system begins to work, and shows the TDS reading on the front panel display screen (Figure 25). NOTE: The system will provide above a 80% TDS rejection rate when working properly, which may vary with a deviation of 10% depending on the source water quality and water usage. The TDS reading may vary as the water is flowing.
Section 3: Filter Life Reminder Activated Carbon Filter {CB} Filter Life: Up to 12 months or 1,800 gallons {for chagrins reduction only} Frey-sediment snd Carbon Block Trellis (CF) Filter Life: Up to 8 months or 800 gallons {or chinning reduction ony) Reverse Osmosis Membrane Filter (RO) Liter Life: Up to 24 months or 3,200 gallons Cea NOTE: Filter life may vary depending on source water quality and water usage. Please replace the filter according to the reminder of the filter life indicators. 4.
2. Filter Life Indicator on the RO Faucet Different light colors will be displayed on the RO faucet corresponding to the filter life status {Figure 28). Blue Yellow Red Figure 29 Light Remaining Life (Day) Remaining Capacity {G} Salas BIA >16 40 Good Yellow <15 S40 Replace Soon Red £0 50 Replace Now Blue Flash i i Flushing Red Flash i i! Malfunction Section 4: Filter Replacement Guide NOTE: If the filter expires, please purchase and replace the filter immediately.
Figure 30 Figure 31 How to Reset the Filter Life indicator (Taking Reset of CB Filter Life indicator as an Example) Press and hold the CB filter life indicator for 7 seconds until the system beeps. NOTE: The filter life rests of CF and RO is the same as the reset of CB. How to Flush the Filter after Replacement: NOTE: The display screen will show the flushing status {Figure 32) during the process.
When power is restored after a blackout, the system will bs forced to flush automatically for 20 seconds. While flushing, the front panel screen will display as seen in Figure 32. The bug, yellow, and red lights will flash in furn for one second, and then the blue light will be on for 20 seconds. The indicators will be off when the flushing is complete. 3.Recycled Fresh Water Flushing Recycled fresh water flushing function is fo ensure each cup of water to be fresh and healthy.
System Maintenance = [f you don't use the system for more than one week, tum on the RO faucet, shut off the cold water valve, and disconnect the power. Seal the filters and store tin the refrigerator (not the freezer). You need to open the RO faucet and allow it fo run for 10 minutes first before using the system again. Otherwise, you need to replace the filters, as bacteria may grow when the system is not used for a long time. * Please replace the filter regularly according to the filter life indicator.
® No Output Water from RO Faucet . Filter expired. Check the filter life indicators to confirm which filter needs to be replaced and replace it immediately. . Low water pressure. Check and confirm the water pressure is between 14.5 psi and 87 psi. . Water supply is off. Tum on the feed water adapter or water supply valve. . Incorrect filter installation. Reinstall the three filters, and make sure they are fitted properly. . A tubing is crimped. Check all tubing and remove any crimps.
a. The system hasn't been used for a long time. Open the RO faucet, allow it to run for a while. The TDS reading will rectum to normal. b. The RO filter expired. Replace the RO filter immediately. ¢. The waste water pipe may be crimped or clogged. Check and remove crimps. Re-align the drain saddle and drainpipe. d. The source water may have a high TDS. Test the source water and filtered water. The filtered water's TDS shall be about of your source water's TDS. This is a normal range.
+ Booster Pump Starting and Stopping Frequently Reminder The front panel screen shows code E04. The buzzer sounds 5 times. There is an internal pressure imbalance. Disconnect the power. Turn on or turn off the RO faucet completely and remove all tubing crimps. Make sure the faucet is not blocked and power on the system again.
quality of water supplies may vary seasonably or over a period of time. Your water usage may vary as well. The manufacturer assumes no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligation on our behalf. You must verify and test the suitability of any information with respect to the product for your specific application. This limited warranty shall be void if: 1.
