Find the installation video Search “Waterdrop Under-Sink Ultra Filtration System Installation” on Register 1-year manufacturer warranty* Visit warranty.waterdropfilter.com and enter the product serial number: Any questions, please contact us. service@waterdropfilter.com 1-888-352-3558 Mon-Fri 8:00 AM-5:00 PM (PST) www.waterdropfilter.
Contents Installation Instructions Before Installation ··································································1 Parts List ··················································································2 Product Introduction ·······························································3 Installation Tips ·········································································4 Installation Steps ····································································5 Step 1: Install the Feed
Installation Instructions Before Installation Inspect the Package Open the box and take out the system housing, all the components, and connect fittings. Inspect them according to the parts list to ensure nothing is left out or damaged during shipping. If there are any parts cracked or broken, please do not proceed with the installation and contact Waterdrop by phone: 1-888-352-3558 Mon-Fri 8:00 AM-5:00 PM (PST) or by email: service@waterdropfilter.com.
Parts List 1 2 3 System Housing X 1 Set Front Cover X1 PP Filter X1 UF Filter X1 Lock Clip X4 Faucet X 1 Set Feed Water Adapter 3/8" and 1/2" X 1 Set Teflon Tape X1 CT Filter X1 AA Battery X3 White 3/8" PE Tubing X 59" Preinstalled White 1/4" PE Tubing X 59" 2
Product Introduction The brief introduction of various parts and sample connections are presented as follows. Please identify and get familiar with these parts and connection points for a smooth installation.
Installation Tips How to Use the Quick-Connect Fittings Mark for Full Insert To connect: Note: There is an existing mark at the end of the tubing for you to confirm if the tubing is fully inserted into the fitting. ••Push the tubing into the fitting until you reach the mark on the tubing. Note: If the tubing is not fully inserted, no seal will be created, and leakage will occur. ••When the tubing is fully inserted, put the blue lock clip on the fitting.
How to Drill a Hole into Your Sink or Countertop (Optional) Note: Please confirm if there is an existing hole available to install the faucet. If not, please drill a hole in accordance with the following steps. It’s highly recommended to watch the YouTube video “How to Drill Faucet Holes” for better understanding of the process. There is also a sticker for your reference to drill the hole. Remember to wear safety glasses to protect your eyes while drilling the faucet hole. 1.
3/8" Cold Water Pipe 1/2" Cold Water Pipe Unscrew Washer Feed Water Adapter 3/8'' Inlet Water Tubing Cold Water Supply Valve Unscrew Figure 3 Figure 4 Step 2: Install the Faucet Note: If there is no hole in your kitchen sink or countertop, you have to drill one (1⅜") or use the hole from the soap dispenser. Refer to Page 5. 1. Insert the faucet spout into the faucet body; 2. Insert the faucet stem into the hole on the countertop; 3.
Step 3: Install the Batteries and Place the System 1. Press to open the battery box (Figure 6). 2. Take out 3 AA batteries and remove the packaging. 3. Install the batteries starting from the negative side, and put the 3 batteries into the battery box in turn. Note: The batteries may not be installed and damage the spring wire if you install the batteries starting from the positive side. 4. After the installation of batteries, the system will beep.
Step 4: Connect Tubing Note: Confirm the tubing length you need and cut the tubing if it’s too long, referring to “How to Use the Quick-Connect Fittings” on page 4. 1. Install the Inlet Water Tubing ••Connect the inlet water tubing from the feed water adapter to the inlet water port and pop the lock clip on the fitting; Note: Make sure it is fully inserted until you reach the mark on the tubing. Inlet Water Tubing Feed Water Adapter Lock Clip 3/8" Inlet Water Tubing Inlet Water Port 2.
again, until reaching 10 minutes. 4. Confirm the 10-minute flushing is completed before turning off the faucet. Make sure the faucet does not leak. 5. Install the front cover (magnetic force). Filter Reset Button PP Figure 7 Owner’s Manual Display and Operation Section 1: Working Mode Display Filter life indicators and power indicator are off during normal water filtration. Touching one of the filter reset buttons slightly will start up all indicators.
Note: Filter life may vary depending on source water quality and water usage. Please replace the filter according to the filter life indicators. There are helpful electronic filter indicators (PP/UF/CT) on the front panel that will notify you the filter replacement by color change and beep. Be sure to reset the filter life indicator every time you replace your filter.
4. Push the filter into the hole with a certain pressure and rotate it a 1/4 turn clockwise, until the triangle mark is aligned with the solid circle on the front panel. You may hear a click when the filter is fitted properly; Note: Repeat the above steps to install the other filters. 5. Reset the filter life indicator and flush the filter after replacement (please refer to the following steps).
Section 4: Battery Life Reminder and Replacement Guide The power indicator displays different status according to the remaining battery power. When the batteries need to be replaced, the power indicator will flash in blue and the system will beep while getting water (Figure 9). Battery life Remaining life (Day) Reminding modes Battery life indicator Buzzer No beep Normal >5 The blue light will be on after touching any indicator slightly. Warning 0<and ≤5 The blue light will flash (on for 0.
System Maintenance ••The installation sequence of filters shall not be reversed to avoid affecting the normal function of the system. ••If you do not use the system for a long time (more than 1 week), it is recommended to turn on the faucet to flush for a while before using it again. ••If the system is not used for a long time, please disconnect the water supply and remove the batteries. ••Please replace the filter regularly according to the filter life indicator.
••Water is not flowing out of the faucet. a. The filters are blocked. If the water quality is poor, the filters may be blocked after a period of use. They will need to be replaced. b. If the filters are not situated in place, install the filters again according to the installation instructions. c. The water inlet valve is not open. Please check the cold water valve and the feed water adapter to ensure that they are fully opened. ••The water tastes weird. a. The filters have expired.
••The filter replacement reminder is inaccurate. a. The service life of a filter is monitored through both usage time and filtered water amount. There will be replacement reminder when either of the two indicators reaches its upper limit. For example, if the filtered water amount reaches the upper limit while the usage time does not, there will also be a replacement reminder. So please follow the instructions and replace the filter on time. b.
Our sole obligation under this warranty shall be repair or replacement of a nonconforming product or parts of this product, or at our option, return of the product and a refund of the purchase price. Our obligation does not include the cost of transportation. We are not responsible for damage in transit, and claim that such damage should be presented to the carrier by the customer. The warranties set forth herein are the only warranties made by us with respect to the product.