Find the installation video Search “Waterdrop D6 RO installation” on Register 1-year manufacturer warranty* Visit warranty.waterdropfilter.com and enter the product serial number. The serial number is the last 7 digits of the barcode on the rear cover and packaging box. Any questions, please contact us. service@waterdropfilter.com 1-888-352-3558 Mon-Fri 8:00 AM-5:00 PM (PST) www.waterdropfilter.com (live chat available) This device complies with part 15 of the FCC Rules.
Contents Installation Instructions Before Installation ··································································1 Product Introduction ·······························································2 Installation Tips ·········································································4 Installation Steps ····································································5 Step 1: Install the Feed Water Adapter ···············································5 Step 2: Install the Faucet ·····
Installation Instructions Before Installation Product Specifications To achieve the optimal performance, it is highly recommended to use the system within the operational parameters. Model Number WD-D6-B Total Filtration Capacity 1,000 gallons Rated Voltage/Frequency 110~120V/60Hz Rated Power 85W Service Flow Rate 0.42 gal/min RO Membrane Working Pressure 58-115 psi Feed Water Pressure 14.
Product Introduction Product Overview Fist Integral Composite Filter Front Cover System Housing Control Panel Parts List Blue 1/4" PE Tubing X 79" White 1/4" PE Tubing X 79" Smart Digital Faucet Drain Saddle Lock Clip X 1 Set X 1 Set X 8 (2 Spare Clips) 2 Red 1/4" PE Tubing X 79" Feed Water Adapter 3/8" and 1/2" X 1 Set
Control Panel Filter Life Indicator Filter Reset Button Power Indicator Power Button Inlet Water Port Outlet Water Port Drain Port Kitchen Faucet Smart Digital Faucet Feed Water Adapter Outlet Water Tubing Inlet Water Tubing Drain Tubing Hot Cold Power 3 Faucet Power Cord
Installation Tips How to Use the Quick-Connect Fittings To connect: Mark for Full Insert Figure 1 Cut Cleanly and Squarely Figure 2 To disconnect: Press Pull Press Figure 3 1. There is an existing mark (Figure 1) at the end of the tubing that you can use to confirm whether the tubing is fully inserted into the fitting. Push the tubing into the fitting until you reach the mark on the tubing. 2. If the tubing is not fully inserted, it will cause leakage.
1. Choose a diamond core bit for granite, and a carbide drill bit for stainless steel. Do not use a hammer drill on natural stone, glass, or ceramic. 2. Glue the sticker to your sink or countertop, and drill a hole referring to the size shown on the sticker (1⅜"). 3. Make an indent with a center punch on a stainless-steel sink before drilling to help guide the bit. 4. Be careful when drilling on a porcelain sink, as it can be easily chipped.
3/8" Cold Water Pipe Screw Washer B Feed Water Adapter Converter 1/2" Cold Water Pipe 1/4'' Inlnet Water Tubing Cold Water Supply Valve A Unscrew Figure 4 Figure 5 Step 2: Install the Faucet NOTE: If there is no hole in your kitchen sink or countertop, you have to drill one (1⅜") or use the hole in the soap dispenser. Refer to Page 4. 1. Insert the faucet stem and power cord into mounting washer 1. 2. Insert the faucet stem and power cord into the hole on the countertop.
Step 3: Install the Drain Saddle 1. Stick the foam seal on the front plate of the drain saddle. Ensure that the hole of the foam seal is aligned with the hole of the front plate (Figure 6). Choose a spot on the drainpipe that is convenient for installing the drain saddle. NOTE: It’s recommended to install the drain saddle on the vertical drainpipe. 2. Drill a 1/4" hole in the drainpipe. Be sure not to penetrate the opposite side of the pipe. 3.
Step 5: Connect Tubing NOTE: •• Confirm the tubing length you need first. Then cut the tubing if it is too long, referring to “How to Use the Quick-Connect Fittings” on page 4. •• Before connecting the PE tubing to the system, remove the plug from the water port. Press and hold the lock sleeve while pulling out the plug. 1. Install the Inlet Water Tubing •• Identify the white 1/4" PE tubing that has been connected to the feed water adapter.
Drain Saddle Drain Tubing Lock Clip Drain Tubing Drain Port Step 6: Connect the Faucet Power Cord Connect the faucet to the system: Insert the power cord which is attached to the RO faucet into the connector at the back of the housing. Faucet Connector System Connector Step 7: Start up the System 1. Turn on the cold water supply valve. Check for leaks. 2. Insert the power plug into the socket. NOTE: •• The system will be powered on and beep 5 times.
sure there are no leaks at the joints, fittings, valves, or tubing connections. •• The water will be undrinkable during the flushing process. The water might appear black at first. •• You will need to do the timekeeping for the 20-minute flushing yourself. Note that when the system continuously works for over 40 minutes, it will enter timeout protection mode. The filter indicator light will flash and the system will not be able to dispense water. Press the power button for 3 seconds.
Owner’s Manual Display and Operation Section 1: Control Panel Display Filter Life Indicator Filter Reset Button Power Indicator Power Button •• Powering on mode: The filter life indicator flashes 5 times. •• Standby/Dispensing water mode: The filter life indicator stays on. When the filter expires, the filter life indicator flashes. •• Energy-saving mode: When the system stands by for 3 hours, it will switch to energy-saving mode. All indicators will be off.
3. Filter life reminder (when the faucet is turned on) •• If the filter has not expired, every segment of the ring light will be on. Then, they will be off one by one, and the remaining segments indicate the life of the filter. NOTE: When there are two segments of the ring light on the screen, the life of the filter remains about 4%-15% (40-150 gallons), which may vary based on your water conditions. It is recommended that you prepare a replacement filter in advance.
automatically flush for 25 seconds. If you turn on the faucet during flushing, the outlet water flow will be slow, which is normal. •• EA: When the TDS display is abnormal, the screen will display “EA”. NOTE: You will need to unplug the power and plug it in again. If the problem has not been resolved, please contact Waterdrop customer service. Section 3: Filter Life Reminder Fist Integral Composite Filter has a service life of 12 months.
5. After replacing the filter, press the power button for 3 seconds. The indicator light will be on and you will hear a “ding” sound. (Note: The system will automatically flush for 25 seconds, and the reset button and power button will flash alternately. 25 seconds later, these two buttons will be on.) After flushing, press the reset button for 3 seconds. Release it when you hear a “ding” sound. The indicator light will change from flashing to constant. 6.
lower or higher, install a pressurizer or pressure reducer accordingly. •• The flow rate will decrease when the ambient temperature is low, which is an inherent characteristic of the filter. •• When the system is dispensing water, there will be a slight vibration and noise, which is normal. •• This system is designed for indoor use only. A floor drain should be located within 1.5 meters of the system to avoid loss caused by water leakage and poor drainage.
Troubleshooting ••The System Cannot Be Powered on After You Insert the Power Plug a. Check the power under the sink, as this occurs primarily when the power under the sink is powered off. Also, check the connection between the power plug and the power outlet to ensure that the system has been correctly plugged into the power outlet. To test whether there is a problem with the system itself, simply pick up the system and try another power outlet. Please contact us if the system cannot be powered on.
••The System Hasn’t Been Used in a While a. Deposits in the tubing may block the filter. Before using the system, turn on the regular tap and allow the water to run for a while. Turn on the filtered water faucet and flush the system. ••Filtered Water from the Faucet Tastes Like Tap Water a. Incorrect tubing installation: Make sure the drain tubing is not connected to the faucet. b.
specifications, or standards is provided solely for your convenience. The quality of water supplies may vary seasonably or over a period of time. Your water usage may vary as well. The manufacturer shall assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligation on our behalf. You must verify and test the suitability of any information with respect to the product for your specific application.
