Watergate Instruction Manual Read and save these instructions Model: Peckish (pack E:T pre il (REC Contact Us £21-888-352-3558 (US) E55 servicepwatendropfittercom
Thanks for your purchase from Water drop, We value your patronage and appreciate your confidence In 125, Counting you manga our customers is something for which we are especially grateful. Please lot us know if we can do anything else to help.
Contents Installation Instructions Before Installation Parts List Product Modulation amo mss iss, installation Tips. installation Steps. wos Ww Ree Step 1: Install the Feed Water Adapter Step 2: Install the RO Faucet... Step 3: Install the Drain Add IE. Step 4: Position the RO Stern Cousin Step 5: Connect Tubing 7 Step & Connect Power Cord. Step 7: Install the Liters Step 8 Start up the System Owner's Manual Display and Operation...
Installation Instructions Before Installation Inspect the Package Open the box and take out the system housing, ai the components and connection fittings. Inspect them according lo the parts ist bo ensure nothing is ie out or damaged during shipping. If there are any parts cracked ar broken, please do na process with the Installation and contact Waterbird customer service by hotlink +1-888-352-3558 (PST) or by mall: servicegwaterdropfifter com.
Parts List Lhe System Housing WD-G3-CB WD-G3-CF 1 Sut Smart Digital White 1/4" Feed Water white 3/8" Lock Clip RO Faucet] PE Tubing Adapter PE Tubing Xs xe *15et Xoo" I Preinstalled— + Preinstalled—1 @ Teflon Tape Drain Saddle 1a" Red 1/4" PE Tubing Power Adapter X1 Set Her 1 Set
Product Introduction The brief Introduction of various parts ard same conceptions are presented as follows.
Installation Tips How to Use the Quick-Connect Fittings To connect: OTE: There Is an existing mark (Figure 1) at the end of the tubing for you to confirm if the tubing is fully inserted into the fitting. = Push the tubing Into the fitting until you reach the mark on the tubing. NOTE: ff the tubing is not fully inserted, no seal will be created and ‘leakage will occur.
1. Choose a glam and care bit for granite, and a carbide dell oir for stainless steel, Do nat use a hammer dif ‘on natural stone, glass or ceramic, 2. flue the sticker on your sink of counter top, and de a noe referring 10 The sticker hole size (17 3. Make an indent with 2 center punch on a staircases stew! sink before drilling to help guide the bit. 4, Be careful when sling on a porcelain sink, as it can be easily chipped, Apply downward pressure firmly on the bit unt you break through the surface. 5.
Step 2: Install the RO Faucet (Non-Al Gap Faucet) GITE: if your kitchen sink or counter top does not have an existing hoe, you wil have to drill one (17). Refer 10 Page 5. 1. Insert the faucet spout Intel the faucet body Figure 6). 2. Insert the faucet stem, power cord and filtered water tubing Into the hole on counter top. 3. Linger the sink, slip on the mur and tighten Tup. Faucet Body = = Faucet Stem he. ' Fluent Power Cord 4 iad Step 3: Install the Drain Saddle 1.
Step 4: Position the RO System Housing MOTE: 1 is not recommended to place the housing against the cabinet, as there may be vibrations when the systole works, 2) The power-supply receptacle for the appliance shall be instated Tn a cabinet or on a wal adjacent to the under counter space Tr which the appliance 1s to be Installed.
2 Install the "FILTERED" Water Tubing + Remove the plug from the "FILTERED water pars identify the white 1/4 PE tubing that 1s per-Instatied with RO facet figure 13), « insert the other end of the tubing into the "FILTERED water part (Figure 14), and pop the lack clip on the fitting. MOTE: take sure it Is duly inserted unt] you reach the mark an the tubing, a FILTERED” FLYWHEELS Water ory i Water Tubing ha. " ozo 2.
Step 6: Connect Power Cord Connect the RO faucet to the system: insert the power cord which Is attached to the RO faucet into he ALICE" connector (Figure 17) at the back of the housing, and tighten the rut Connect Power Adapter terse the DC head of the power adapter inch the "SOWER' port at the back of the housing Fare 18), MOTE: Ease do not connect pow: socket now. “POWER” Port FRANCE Connector Step 7: Install the Liters Each fitter 1s marked with a logo (CB/CF/RD) and an installation arrow.
Step 8: Start up the System I. Turn: on the cold water supply valve, Check for leaks; 2.
5. Confirm the flush is completed before turning off te RO faucet and ensure is not leaking. &. Please fix the power adapter with the cable te so that & does not move by impact. To avoid allure, stay away from any water sources, including pipe fittings, the bottom of the basement, and wet floors. * Please note that the reading in the figure is only used as an example, and the actual reading may vary according to different water conditions.
Section 2: Filter Life Reminder MITE: Fitter fe may vary depending on source water quality and water usage. Please replace the fighter according To the reminder of the filter fe Indicators. 1. Filter Life Indicator on System Housing There are helpful electronic fighter indicators (CARP) on the front panel (grue 26) that will notify you ta perform a routine fair replacement by color change. Be sure to reset the filter fe indicator every time you replace your fair.
Display Tine: « All indicators will go off after § minutes when the stern stops making water. « Check the fighter life status by touching the indicators, and the fights will go off in 30 seconds. 2. Filter Life Indicator on the RO Faucet Different light coon displayed on RO faucet Indicate different filter ife status.
Hew to Reset the Filter Life indicator (Taking Reset of CB Liter Life storytelling as an Example oid the CB f tier life indicator for 7 seconds unt! the system beeps.
3. Recycled Rash Water Flushing Recycled fresh water flushing function Ts to ensure each cup of water to be fresh and healthy. The system will aromatically recycle fresh water and start gushing after It has dispensed water over 5 minutes.
System Maintenance «#you dart use the stern for mare than one week, tum on the RO faucet, shut off the cold water valve, and disconnect the power, Seal the fighters and store it in the refrigerator (not the freezes). You need to open the RO faucet and slow 1 ke run for 10 minutes fins before using the system again. Otherwise, you need to replace the filters, as bacteria may grow when the system fs rot used for a long time.
+ Low Water Flow at the RO Faucet a. Leak from tubing connection, Check and ensure al tubing Is Install ed contently and completely. b. Filter expires. Check the fighter Ife indicators to confirm which fighter needs to be replaced and replace ft intermediately, © Low water refrigerate, Be sure to use the system at a temperature of 41.100°F 4, Use well water as the source and the feed water has rat been through a per-fitration system, the filter nas been clogged.
a. The reading tested 7y the DIS Meter 's the TDS of static water In the container while the TDS reading spiraled by the system Is the TDS of flowing water, AS a result the TDS readings are different. b. There are errors in the TDS Meter tests. = Filtered Water from the RO Faucet Tastes Like Tap Water a Incorrect wiling Translation. Make sure the waste water tubing is not connected with RO faucet. 1, The fighters ane not well installed, Make sure the filters are placed properly, «Fitter expires.
3 The feed water rust hive a pH between 85 and 85; 4. Turbidity mus: be less than 1.0 NTU 5. Tne feed water MUST be municipal tag water 6. The Total Dissolved Solids (TDS) must be fess than 750 ppm, 7. The max hardness must be less than 7 grains per halon, Any Information or suggestion with respect to our product canceling applications, specifications or standards is provided solely for your convenient: reference.
