Specifications

ManualsBrandsWaters Network Systems ManualsComputer equipmentES1008-TX

OPERATING MANUAL

ES1008 Family of Enclosed Switches

8-Ports 10/100Mbps Switching

With Optional 9

Port in 100Mbps Fiber or 10/100Mbps Copper

CORPORATE HEADQUARTERS MANUFACTURING/CUSTOMER SERVICE

13705 26

Avenue N., Suite 102 2411 Seventh Street NW

Minneapolis, MN 55441 Rochester, MN 55901

Phone: (800) 441-5319 Phone (800) 328-2275

Fax: (763) 509-7450 Fax: (507) 252-3734

E-mail: netinfo@wtrs.com www.watersnet.com E-mail: netinfo@wtrs.com

Summary of content (9 pages)

PAGE 1
OPERATING MANUAL ES1008 Family of Enclosed Switches 8-Ports 10/100Mbps Switching With Optional 9th Port in 100Mbps Fiber or 10/100Mbps Copper CORPORATE HEADQUARTERS 13705 26th Avenue N., Suite 102 Minneapolis, MN 55441 Phone: (800) 441-5319 Fax: (763) 509-7450 E-mail: netinfo@wtrs.com www.watersnet.com MANUFACTURING/CUSTOMER SERVICE 2411 Seventh Street NW Rochester, MN 55901 Phone (800) 328-2275 Fax: (507) 252-3734 E-mail: netinfo@wtrs.
PAGE 2
Table of Contents 1.0 Specifications .............................................................................................................................................. 3 1.1 Technical Specifications................................................................................................................................ 3 2.0 Product Description .................................................................................................................................... 4 2.
PAGE 3
SPECIFICATIONS 1.
PAGE 4
LEDs: Per Port LK/Act: Steady ON for Link with no traffic, blinking indicates port is transmitting and receiving F/H: ON = Full-Duplex Mode; OFF = Half-Duplex Mode 100/10: ON = 100Mbps speed; OFF = 10Mbps Operating Environment Ambient Temperature: 32° to 105° F (0° to 50°C) Storage Temperature: -5° to 160°F (-20°to 60°C) Ambient Relative Humidity: 10% to 95% (non-condensing) Power Supply (Internal) AC Power Connector: IEC-type, male recessed at rear of chassis, with adjacent manual ON-OFF switch (on AC mode
PAGE 5
each 100Mbps port and a proper link (LK lit) must be made with the device at the other end of the cable in order for the LK LEDs to provide valid indications of operating conditions. 2.2 10/100 Dual-speed Switched Ports, RJ45 (Copper) All ES1008 models have 8 10/100Mbps dual speed switch ports.
PAGE 6
more frames from entering by forcing a collision signal on all receiving half-duplex ports in order to stop incoming traffic. The latency (the time the frame spends in the switch before it is sent along or forwarded to its destination) of the ES1008 switches varies with the port-speed types, and the length of the frame is a variable here as it is with all store-and-forward switches.
PAGE 7
The following procedure describes how to connect a 10BASE-T or 100BASE-TX twisted pair segment to the ES1008 RJ45 port. The procedure is the same for both unshielded and shielded twisted pair cables. 1. Using standard twisted pair media, insert either end of the cable with an RJ45 plug into the RJ45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used. 2. Connect the other end of the cable to the corresponding device. 3.
PAGE 8
4.2 Manual Switches for Uplink Button, for RJ45 Port #1 Only The ES1008 switch has a manual uplink sliding switch, located on the front panel next to 10/100Mbps RJ45 port #1 which it controls. It enables the port’s cable to either connect to a user station node (push in) or to be cascaded (push out) to a 10/100Mbps repeater or switching hub in the network. Verify proper uplink button position by noting Port 1’s LK (link) LED status, which is illuminated when a proper link is made. 4.
PAGE 9
5.0 TROUBLESHOOTING All Waters’ Ethernet products are designed to provide reliability and consistently high performance in all network environments. The installation of Waters’ ES1008 switches is a straightforward procedure (see Section 3); the operation is also straightforward and is discussed in Section 4. Should problems develop during installation or operation, this section is intended to help locate, identify and correct these types of problems.