INDUSTRIAL PLP PULLDOWN FAUCET INSTALLATION INSTRUCTIONS Model #s: 9300, 9400, 9410, 9700, 9800, 9810, 9900, 9910, 9930, 9940 9350, 9450, 9460, 9750, 9850, 9860, 9950, 9960, 9980, 9990
BEFORE YOU BEGIN YOUR INSTALLATION: 1 2 Turn off water supply. 3 Observe all local plumbing codes. 4 DO NOT use petroleum based products on this faucet. Inspect plumbing for signs of damage. Replace as necessary. REQUIRED TOOLS: Adjustable Wrench Channel Locks Phillips Screwdriver HANDLE POSITION Waterstone faucets are designed to be installed in 3 different faucet positions. Choose to have the handle on left, front or right.
ADJUST HANDLE FOR BACKSPLASH CONNECT THE PULLDOWN SPRAY HOSE FIG.1 ORIGINAL FACTORY POSITION MAY HIT BACKSPLASH NEW ADJUSTED POSITION CLEARS BACKSPLASH On some kitchen countertops, the handle may hit the backsplash when the faucet handle is positioned to the left or right (Fig. 1). Remove the handle, turn it approximately 22.5 degrees forward, then reattach. B A CONNECTING SUPPLY HOSES Before connecting supply POSITION hoses, flush ORIGINAL FACTORY supply stops to clear any debris.
CLEANING DEBRIS SCREEN CLEANING AERATOR - TOGGLE SPRAYER 1. Turn off water supplies underneath sink and remove any water pressure by opening the faucet handle. 2. Unscrew sprayer (A) from spray hose by holding knurled swivel (B). 3. Inspect, remove and clean debris screen (C) in sprayer. Once cleaned, replace debris screen and reattach to swivel. 4. Close faucet handle and turn on water supplies. Make sure sprayer is secure and sealed by running faucet. B C A 1. 3. A 2. B 2. 5. C 1.
INSTALL SOAP/LOTION DISPENSER (OPTIONAL) 1. 3. 2. 1-3/8” HOLE A Pull and remove spout (A) from dispenser body (B). Remove clamp nut (C) and brass spacer (D) from threaded shroud. B COUNTER OR SINK E Fit dispenser body through 1-3/8” hole on counter or sink. (No plumbers putty is required). Slide brass spacer onto shroud. Screw clamp nut and tighten snug. D C 4. 5. Insert open end of red tubing down through dispenser base and into plastic bottle. Fill plastic bottle with soap or lotion.
5. 7. 6. 8. GARBAGE DISPOSAL E E G Tighten clamp screws (E) securely with screwdriver. Slide other end of tubing (F) into tube fitting at bottom of control box (G). Hand tighten switch base back down to cover threads. INSTALL SINGLE PORT AIR GAP (OPTIONAL) 1. 2. A Twist and pull air gap cover (A) off of upper cap nut (B). Unscrew and remove cap nut B from piping (C). D Plug control box into undersink electrical outlet. Plug garbage disposal into either dual outlet. F 3. 1-1/2” HOLE E C 4.
INSTALL DUAL PORT AIR GAP (OPTIONAL) 1. 3. 2. 4. D A 1-1/2” HOLE E B C Pull air gap (A) off of upper cap nut (B). Unscrew and remove cap nut from piping (C). Unscrew and remove top clamp nut (D) from both threadings on piping. Slide gasket (E) off piping and remove. 5. F Slide gasket down and screw top clamp nut back onto piping. Adjust the two clamp nuts to fit countertop thickness. (No plumbers putty is required). From underneath counter top, fit air gap piping upward through 1-1/2” hole. 6.