User Manual

ManualsBrandsWaterworks ManualsAccessories for water.25 One Hole High Profile Bar Faucet, Metal Handle

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST

.25

One Hole High Profile Bar Faucet with Metal Lever Handle

Installation Guidelines

Page 1 of 2

Rev

10.31.2014

These guidelines have been prepared for the professional contractor to aid in the installation of:

.25 ONE HOLE HIGH PROFILE BAR FAUCET WITH METAL LEVER HANDLE (STYLE No. PTKM30, PT30KM UK).

All dimensions are based on original specification and are subject to change and variation.

Please consult your Design Associate for current specifications.

STYLE No. PTKM30†

SPECIFICATIONS:

Deck Thickness Maximum: 1-3/8” (35mm)

Fittings Hole Diameter: Ø1-1/2” (38mm)

Handle Turn Angle: Quarter Turn Each Way

Inlet Connection Size: 3/8”

Inlet Connection Type: Compression Connection Adapters†

Restricted Maximum Flow Rate: 2.2gpm (8.3liters/min)

Spout Reach: 5-1/2” (140mm)

Spout Swivel: No

Water Pressure Minimum: 20 psi (1.4 Bar)

Water Pressure Maximum: 80 psi (5.5 Bar)

Water Pressure Recommended: 45 psi (3 Bar)

† UK Style No. PT30KM is supplied with 2 BSP adapters,

assembly required

IMPORTANT:

 To ensure this product is installed properly, you must

read and follow these guidelines.

 The owner/user of this product must keep this

information for future reference.

 This product must be installed by a professional

licensed contractor.

 Be sure your installation conforms to all federal, state,

and local codes.

 In the State of Massachusetts, all installations must

comply with the rules and regulations set forth within

248 CMR.

 Refer to the specification and assembly drawings

attached. Product is sold partially assembled but

shown fully disassembled for illustrative and service

purposes only.

 Inspect the product to ensure you have all the parts

required for proper installation.

 Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

 DO NOT use putty. Putty contains oil and can cause

permanent discoloration on certain materials such as

marble, granite and any porous surface.

INSTALLATION

1. Remove the MOUNTING NUT, METAL WASHER, and

RUBBER WASHER from the SHANK. See FIGURE - 01.

Do NOT remove the RUBBER WASHER beneath the

ESCUTCHEON.

FIGURE – 01

2. Ensure that the HOSES are securely tightened to the

EXTENSION TUBES, then insert the HOSES through

the hole on the mounting surface making sure the

RUBBER WASHER is beneath the ESCUTHCEON.

ESCUTCHEON

RUBBER

WASHER

METAL

WASHER

MOUNTING

NUT

ESCUTCHEON

RUBBER

WASHER

METAL

WASHER

MOUNTING

NUT

Summary of content (2 pages)

PAGE 1
.25 One Hole High Profile Bar Faucet with Metal Lever Handle STYLE No. Installation Guidelines  Refer to the specification and assembly drawings attached. Product is sold partially assembled but shown fully disassembled for illustrative and service purposes only. PTKM30†  Inspect the product to ensure you have all the parts required for proper installation.  Use only a strap wrench or protected/smooth-jaw wrench on any finished surface.  DO NOT use putty.
PAGE 2
.25 One Hole High Profile Bar Faucet with Metal Lever Handle Installation Guidelines 3. Re-install the RUBBER WASHER, METAL WASHER and MOUNTING NUT. Securely tighten the MOUNTING NUT to secure the SPOUT to mounting surface. SPOUT 4. Connect the ADAPTERS from the HOSES to the water supplies making sure the O-RINGS are inside the ADAPTERS. See FIGURE – 02. SET SCREW ADAPTER GLAND COVER RETAINING COLLAR O-RING HANDLE SET SCREW FIGURE - 02 FIGURE - 03 5.