User`s manual

WATLOW Series 982 User’s Manual A.5
Appendix
982 Index
% out LED 3.1
A
A/D overflow error 8.6
A/D underflow error 8.5
abort set point 4.31
actions, error code 8.6
address 4.40
alarm 2 4.17
alarm 2 high 5.5
alarm 2 low 5.5
alarm 3 4.19
alarm 3 high 5.6
alarm 3 low 5.6
alarm 4 4.22
alarm 4 high 5.7
alarm 4 low 5.7
alarms 8.4 - 8.5
alarm silencing 8.5
ambient error 8.6
ambient temperature 6.4
analog output 4.25
annunciator 4.32
auto-tune 5.8
auto-tune set point 4.33
auto-tuning 8.1 - 8.2
B
battery backup DIP 1.4
baud rate 4.39
burst fire 9.2 - 9.3
C
Calibration Menu 6.7 - 6.8
calibration offset 1 4.6
calibration offset 2 4.10
celsius-fahrenheit 4.29
communications 9.4 - 9.5
Communications Menu 4.38 - 4.42
configuration error 8.6
cycle time, output 1 5.14
cycle time, output 2 5.17
D
data bits and parity 4.39
date 6.3
dead band 5.17, 9.6 - 9.7
decimal 1 4.4
Declaration of Conformity A.10
default 6.8
derivative, output 1 5.13
derivative, output 2 5.16
deviation alarm 8.4
dev LED 3.1
Diagnostics Menu 6.2 - 6.6
digital event input 1 2.10
digital event input 2 2.9
digital events 9.8 - 9.9
DIP switch
external power supply 1.5
hardware lock/battery backup 1.4
locations and functions 1.3
universal signal input type 1.6
display loop 3.2
display key 3.1
display tests 6.6
down key 3.1
E
editing a profile 7.10 - 7.11
end 7.4
end step 7.4
environmental chamber 9.7
error codes 8.5 - 8.6
error latching 4.29
event 3
set point step 7.2
soak step 7.3
event 4
set point step 7.2
soak step 7.3
event input 1 4.30
event input 1 status 5.3
event input 1 wiring 2.10
event input 2 4.31
event input 2 status 5.3
event output 3 status 5.4
event output 4 status 5.4
event outputs 7.6 - 7.7
external power supply DIPs 1.5
F
Factory Menus 6.1 - 6.8
file 7.1
front panel 3.1
G
gas-fired furnace 9.15
Global Menu 4.28 - 4.37
guaranteed soak deviation 4.34, 7.7
H
hardware lockout DIP switch 1.4
heater with digital event 9.9
heat-treat oven 9.15
high power limit 4.33
hold/run key 3.1
hold/run LED 3.1
hour 7.3
humididty chamber 9.11
hunt 4.10
hysteresis 1 4.14
hysteresis 2 4.16
hysteresis 3 4.20
hysteresis 4 4.23
I
idle set point 4.36
input 1 4.3
input 1 wiring 2.8
input 1, digital event 2.10
input 2 4.8
input 2 wiring 2.9
input 2, digital event 2.9
input DIP switches 1.6
input filter 9.10 - 9.11
Input Menu 4.2 - 4.11
input module types 6.4
input/output isolation 2.4
installation procedure 2.1 - 2.3
integral, output 1 5.12
integral, output 2 5.15
interface type 4.41
J
jump count 7.4
jump file 7.4
jump-loop 7.8
jump-loop step 7.4
jump step 7.4
L
L1... L4 3.1
latching 2 4.17
latching 3 4.21
latching 4 4.24
learn high range 4.9
learn low range 4.9
link file 7.4
linking profiles 7.12
lockout 4.37
lower display 3.1
low power limit 4.32
M
manual tuning 8.2 - 8.3
master step chart 7.14
menu overview 1.2
messages, error code 8.5
minutes 7.2, 7.3
mode key 3.1
N
non-volatile checksum error 8.6
O
Operation Menu 5.1 - 5.18
output 1 4.13
output 1 wiring 2.11
output 2 4.15
output 2 wiring 2.12
Index