Manual

ENGLISH INSTRUCTIONS
WATTS
PRESSURE GAUGE
(2 PLACES)
WATTS
SHUTOFF VALVE
(2 PLACES)
WATTS
BACKFLOW
PREVENTER
WATTS
PRESSURE
REGULATOR
(2 PLACES)
WATER
METER
SUPPLY
TO FIXTURES
TO SILLCOCK
WATTS
PRESSURE GAUGE
(2 PLACES)
WATTS
SHUTOFF VALVE
(2 PLACES)
WATTS
BACKFLOW
PREVENTER
WATTS
PRESSURE
REGULATOR
WATER
METER
SUPPLY
TO FIXTURES
TO SILLCOCK
Typical Installation
Series Installation
Series installations are recommended where very high supply pressure
must be reduced to a very low downstream pressure. Reducing the
pressure in stages eliminates whistling and noise.
Parallel Installation
Parallel installations are recommended where high flow or low flow
demand is intermittent/occasional. They are also used for installations
where service cannot be interrupted.
IS-N45B-M1 1323 EDP# 1915390 © 2013 Watts
USA: Tel. [phone] • Fax: [phone] • www.watts.com
Canada: Tel. [phone] • Fax: [phone] • www.watts.ca
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects
in material and workmanship under normal usage for a period of one year from the date of original ship-
ment. In the event of such defects within the warranty period, the Company will, at its option, replace
or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY
GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive
remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing
other property which is damaged if this product does not work properly, other costs resulting from labor
charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water
conditions, chemical, or any other circumstances over which the Company has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance
or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow
the exclusion or limitation of incidental or consequential damages. Therefore the above limitations may
not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights
that vary from State to State. You should consult applicable state laws to determine your rights. SO
FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT
BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL
SHIPMENT.
IS-N45B-M1 1323 EDPN.º 1915390 © 2013 Watts
EE.UU.: Tel. [phone] • Fax: [phone] • www.watts.com
Canadá: Tel. [phone] • Fax: [phone] • www.watts.ca
Garantía limitada: Watts Regulator Co. (en adelante, “la Compañía”) garantiza, por un período de un año a
partir de la fecha de embarque original, que sus productos están libres de defectos en materiales y mano de obra
bajo condiciones de uso normal. En caso de que se encuentren tales defectos dentro del período de garantía, la
Compañía reemplazará o reacondicionará, a su elección, el producto sin costo alguno.
LA GARANTÍA AQUÍ ESTIPULADA SE OTORGA EN FORMA EXPRESA Y ES LA ÚNICA GARANTÍA
OTORGADA POR LA COMPAÑÍA EN RELACIÓN CON EL PRODUCTO. LA COMPAÑÍA NO OTORGA NINGUNA
OTRA GARANTÍA, YA SEA EXPRESA O IMPLÍCITA. LA COMPAÑÍA POR LA PRESENTE RENUNCIA
ESPECÍFICAMENTE A TODAS LAS DEMÁS GARANTÍAS, EXPRESAS O IMPLÍCITAS, INCLUYENDO SIN
LIMITACIÓN, LAS GARANTÍAS IMPLÍCITAS DE APTITUD PARA LA COMERCIALIZACIÓN E IDONEIDAD PARA
UN PROPÓSITO EN PARTICULAR.
La solución descrita en el primer párrafo de esta garantía constituirá la única y exclusiva solución por
incumplimiento de garantía, y la Compañía no se hará responsable por daños accidentales, especiales o
indirectos, incluyendo sin limitación, la pérdida de ganancias o el costo de reparación o reemplazo de otra
propiedad que resulte dañada por el mal funcionamiento de este producto, otros costos resultantes por mano
de obra, retardos, vandalismo, negligencia, obstrucciones ocasionadas por materiales extraños, daños debidos
a condiciones adversas del agua, químicos o cualquier otra circunstancia sobre la cual la Compañía no tenga
control. Esta garantía no tendrá validez en cualquier caso de abuso, uso indebido, aplicación incorrecta,
instalación inadecuada, o mantenimiento adecuado o alteración del producto.
Algunos Estados no permiten limitaciones en la duración de una garantía implícita y algunos Estados no permiten
la exclusión o limitación de daños accidentales o indirectos. Por lo tanto, es posible que las limitaciones anteriores
no sean aplicables en su caso. Esta garantía limitada le da derechos legales específicos; usted podría tener tam-
bién otros derechos que varían según el Estado. Usted debe consultar las leyes estatales aplicables para deter-
minar sus derechos. EN LA MEDIDA EN QUE SEA CONGRUENTE CON LAS LEYES ESTATALES APLICABLES,
CUALQUIER GARANTÍA IMPLÍCITA QUE NO SEA RECHAZADA, INCLUYENDO LAS GARANTÍAS IMPLÍCITAS DE
APTITUD PARA LA COMERCIALIZACIÓN E IDONEIDAD PARA UN PROPÓSITO EN PARTICULAR, SE LIMITA EN
SU DURACIÓN A UN AÑO A PARTIR DE LA FECHA DEL EMBARQUE ORIGINAL.
USA: Tel. [phone] • Fax: [phone] • www.watts.com
Canada: Tel. [phone] • Fax: [phone] • www.watts.ca
Garantie limitée : Watts Regulator Co. (la « Société ») garantit que chacun de ses produits est exempt de
vice de matériau et de fabrication dans des conditions normales d’utilisation pour une période d’un an à
compter de la date d’expédition d’origine. Dans l’éventualité où de tels vices se manifesteraient pendant
la période de garantie, la Société, à sa discrétion, remplacera ou reconditionnera le produit sans frais.
LA PRÉSENTE GARANTIE EST EXPRESSE ET REPRÉSENTE LA SEULE GARANTIE OFFERTE PAR
LA SOCIÉTÉ POUR CE PRODUIT. LA SOCIÉTÉ N’OFFRE AUCUNE AUTRE GARANTIE, EXPRESSE OU
TACITE. PAR LA PRÉSENTE, LA SOCIÉTÉ REJETTE SPÉCIFIQUEMENT TOUTE AUTRE GARANTIE,
EXPRESSE OU TACITE, NOTAMMENT TOUTE GARANTIE TACITE DE QUALITÉ MARCHANDE OU
D’ADAPTATION À UN BUT PARTICULIER.
Le recours décrit dans le premier paragraphe de cette garantie constitue le seul recours à toute violation
de la présente garantie. La Société ne saurait être tenue responsable de tout dommage accessoire, spé-
cial ou indirect, y compris, de façon non limitative : la perte de profits ou le coût afférent à la réparation ou
au remplacement d’autres biens qui seraient endommagés par suite du fonctionnement incorrect dudit
produit ; d’autres coûts résultant de frais de main-d’œuvre, de retards, de vandalisme, de négligence,
d’une obstruction causée par des matériaux étrangers, de dommages causés par une eau impropre,
des produits chimiques ou par tout autre événement échappant au contrôle de la Société. La présente
garantie est déclarée nulle et non avenue en cas d’usage abusif ou incorrect, d’application, d’installation
ou d’entretien incorrects ou de modification du produit.
Certains États n’autorisent pas les limitations de durée d’une garantie tacite ou l’exclusion ou la limita-
tion des dommages accessoires ou indirects. Les limitations susmentionnées peuvent donc ne pas
s’appliquer à vous. Cette garantie limitée vous donne des droits spécifiques et il se peut que vous ayez
aussi d’autres droits qui varient d’un État à l’autre. Veuillez vous référer aux lois applicables de l’État pour
déterminer vos droits en la matière. DANS LA MESURE PERMISE PAR LA LOI APPLICABLE DE L’ÉTAT,
TOUTES LES GARANTIES TACITES NE POUVANT PAS ÊTRE REJETÉES, Y COMPRIS LES GARANTIES
TACITES DE QUALITÉ MARCHANDE ET D’ADAPTATION À UN BUT PARTICULIER, SONT LIMITÉES
QUANT À LEUR DURÉE À UN AN À COMPTER DE LA DATE D’EXPÉDITION D’ORIGINE.
1. Mark pipe as shown.
This is pipe insertion depth.
2. Clean pipe end.
1. Remove collet clip.
2. Depress collet.
3. Pull tubing from tailpiece.
3. If using PEX tubing, insert pipe stiff-
ener (provided) into end of pipe.
4. Push tubing into tailpiece up to mark.
5. Insert collet clip.
Quick-Connect Installation
To Connect:
To Disconnect:
WATTS
PRESSURE GAUGE
(2 PLACES)
WATTS
SHUTOFF VALVE
(2 PLACES)
WATTS
BACKFLOW
PREVENTER
WATTS
PRESSURE
REGULATOR
(2 PLACES)
WATER
METER
SUPPLY
TO FIXTURES
TO SILLCOCK
IS-N45B-M1 1323 EDP# 1915390 © 2013 Watts
IS-N45B-M1
N45BDU-M1
N45BDU-QC-M1
Troubleshooting — High System Pressure
If the downstream system pressure is higher than the set pressure under no flow
conditions, the cause could be thermal expansion, pressure creep or dirt/debris on
the seat.
Thermal expansion occurs whenever water is heated in a closed system. The system
is closed when supply pressure exceeds 150 psi (10.3 bar), or a check valve or back-
flow preventer is installed in the supply piping.
You must make provisions for pressure relief protection of your plumbing system
and components. The use of a relief valve such as the Watts 530C, BRV, Governor
80, or 3L or potable water expansion tank such as the Watts DET, PLT or DETA
may be required.
To determine if this is the result of thermal expansion, try briefly opening the cold water
tap. If the increased pressure is caused by thermal expansion, the pressure will imme-
diately be relieved and the system will return to the set pressure.
Watts offers a pressure test gauge, model 276H300 to assist you in determining if you
have high water pressure. The 276H300 when attached to a hose bibb registers the
highest pressure reading over the period of time it is left on the system.
SEAT/STEM MODULE
Adjusting
Screw
Lock Nut
Lock Seal
Name Plate
Spring
Washer
Spring
Spring
Cage
Stem
Nut
Slip
Ring
Seat/Stem
Module
Strainer
Stem
Nut
Strainer
Installation Instructions
1. The valve should be installed by a licensed contractor in accordance with local
codes and ordinances.
2. This valve should be installed where it is accessible with sufficient clearance for
cleaning, service, or adjustment.
3. Before installing the valve, be sure that the pipe ends are reamed and threads
are cut to size. For valves with Quick-Connect tailpieces refer to “Quick-
Connect Installation” instructions below.
4. Flush the lines to remove all loose scale, dirt and other foreign matter that can
damage or clog the valve.
5. Install the regulator with the arrow on the body pointing in the direction of the
flow.
6. Regulator may be installed vertically or horizontally (upright or inverted).
7. Start Up — Open cold water supply then hot water supply. Inspect for leaks.
The valve should be inspected annually to assure maximum life and performance.
LFN45B-M1 Valves are suitable for accessible outdoor or pit installations.
Maintenance Instructions
• To clean strainer or replace seat/stem module shut off supply, loosen Locknut
and Lock Seal and back off Adjusting Screw.
• Remove Spring Cage, Spring, Washer and Slip Ring. Grasp Stem Nut with fingers
or pliers and lift module from body.
• Replace module and reassemble valve.
• Readjust pressure setting.
Adjustment
Regulator is factory preset to 50 psi (344 kPa). To adjust pressure setting, loosen
the lock nut and turn the adjusting bolt clockwise to increase pressure, counter
clockwise to decrease pressure.
Any time a reducing valve is adjusted, the use of a pressure gauge is recommended
to verify correct pressure setting. Do not bottom out adjusting screw on spring cage.
Repair Kits
KIT NO. SIZE ORDERING CODE KIT INCLUDES
in. mm
1
⁄2 – 1
1
⁄2,
3
⁄4, 1 15, 20, 25 0006960 Seat/Stem
N45B/N45B-EZ-RK Module
/LFN45B
Bypass Feature
This regulator has a built-in thermal expansion bypass feature. This feature prevents
downstream pressure from rising to more than 10 psi (69 kPa) above the supply
pressure.
The Bypass feature will not prevent the pressure relief valve from opening on the hot
water supply system with pressures above 150 psi (10.3 bar).
LFN45B-M1
Water Pressure Reducing Valve
Válvula reductora de la
presión del agua
Régulateur de pression d'eau
1
⁄2" - 1" (15-25mm)
Installation Instructions
Instrucciones
de instalación
Instructions
d’installation
PEX tubing only
Pipe Stiffener
Tail Piece
1
1
⁄2 in. (38.1mm)
1
3
⁄4 in. (44.45mm)
1
7
⁄8 in. (47.63mm)
1
⁄2 in.Pipe (12.7mm)
3
⁄4 in.Pipe (19.05mm)
1 in.Pipe (25.4mm)
WARNING: This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm.
For more information: www.watts.com/prop65
ADVERTENCIA: Este producto contiene sustancias químicas
que en el Estado de California se conocen como causantes
de cáncer y malformaciones u otros daños reproductivos.
Para más información: www.watts.com/prop65
AVERTISSEMENT: Ce produit contient des produits chi-
miques reconnus par l’État de Californie comme étant can-
cérigènes et pouvant provoquer des anomalies congénitales
ou affecter la capacité de reproduction.
Pour plus d'informations: www.watts.com/prop65
NOTICE
WARNING
Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information can result in death,
serious personal injury, property damage, or damage to the equipment.
Keep this Manual for future reference.
!
CAUTION
!
NOTICE
NOTICE
For valves with CPVC or PEX end connections do not exceed the
tubing manufacturers pressure and temperature ratings. Refer to the
tubing manufacturers product specifications for that information.
WARNING
!